Timex T231Y AM/FM Clock Radio Manual

Timex T231Y AM/FM Clock Radio Manual

Also See for T231Y:

Advertisement

Timex T231Y AM/FM Clock Radio Manual

What's in the Box

This product ships with the following items. Make sure all are present.

Product Care

  • Place the unit on a level surface away from sources of direct sunlight or excessive heat.
  • Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material should be placed between it and the furniture.
  • Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as Benzene, thinner or similar materials can damage the surface of the unit.

Controls Overview

Controls Overview - Top Panel
Top Panel

Controls Overview - Rear Panel
Rear Panel

Display

Display

When lit, indicates Buzzer or Radio is Alarm 1 alarm source. If neither is lit, Alarm 1 is not armed

When lit, indicates Buzzer or Radio is Alarm 2 alarm source. If neither is lit, Alarm 2 is not armed

Installing and Replacing Backup Batteries

Your new Timex Clock Radio includes a battery backup system that will maintain the time and alarm settings during a temporary power interruption.

  1. Keep unit connected to AC power when changing batteries to avoid losing yoursettings.
  2. Press on the battery door locking tab to open and remove the battery door.
  3. Check the correct polarity (+/ - ) markings in the battery compartment and install two"AAA"batteries (not included).
  4. Replace the battery door.

NOTE: With batteries installed, the display will turn off during a power failure but the clock will continue to run and maintain your alarm settings. The alarm will not sound when operating on batteries.

Set Up

Connecting to Power Source

Connect the AC plug into a working wall outlet that is not controlled by a wall switch.
The unit does not operate on batteries (the battery back up system maintains clock settings during power failures).
Connecting to Power Source

Turning the Unit ON or OFF

  • Press and release the Power/Mode/Alarm Reset Button on the unit at any time to turn the unit On.
  • Press and hold the Power/Mode/Alarm Reset Button to turn the unit Off.

Setting the Time

  1. Make sure unit is OFF. To confirm unit is off, press and hold the Power/Mode/Alarm Reset Button once or twice for 2 seconds until OFF appears on the display.
    Setting the Time - Step 1 - Turn off the unit
  2. Press and hold the Clock/Preset Button until the time flashes on the display.
    Setting the Time - Step 2
  3. Press and release the Hour/ Button to adjust the HOUR.
    Setting the Time - Step 3 - Adjust the Hour
    NOTE: The PM indicator will light when the hour is set for PM. There is no AM indicator.
  4. Press and release the Minute/ Button to adjust the MINUTES.
    Setting the Time - Step 4 - Adjust the minutes
  5. Press and release the Clock/Preset Button to complete time setting.
    Setting the Time - Step 5 - Complete time settings

Setting and Using Alarms

This unit has two independent alarms, Alarm 1 and Alarm 2. Each is set and operates in the same way. Instructions below show Alarm 1. Follow the same method to set Alarm 2.

  1. Press and hold the Alarm 1 Button until current alarm time flashes on the display.
    Setting and Using Alarms - Step 1
  2. Press and release the Hour/ Button to adjust the HOUR.
    NOTE: The PM indicator will light when the hour is set for PM. There is no AM indicator.
    Setting and Using Alarms - Step 2
  3. Press and release the Minutes/ Button to adjust the MINUTES.
    Setting and Using Alarms - Step 3
  4. Press and release the Alarm 1 Button to complete alarm time setting.
    Setting and Using Alarms - Step 4

SELECTING YOUR ALARM SOURCE/DISARMING THE ALARM

Press and release the Alarm 1 Button repeatedly as needed to cycle to desired alarm mode: Buzzer (default), Radio (last AM or FM station played) or Off (alarm is no longer active). Note that the last radio volume listened to will be the radio alarm volume.
SELECTING YOUR ALARM SOURCE/DISARMING THE ALARM

RESETTING AN ALARM TO COME ON THE NEXT DAY

To silence any sounding alarm and reset it come on the next day at the same time, press and release either the Power/Mode/Alarm Reset Button, Alarm 1 Button or Alarm 2 Button.
RESETTING AN ALARM TO COME ON THE NEXT DAY

SNOOZE

Press and release the Snooze/Sleep Button when the alarm sounds to silence it for 9 minutes. Snooze can be used several times during alarm.
SNOOZE

Setting and Using the Radio

BASIC RADIO OPERATION

TIP: Extend FM antenna for best reception.

  1. Press and release the Power/Mode/Alarm Reset Button as needed to turn unit On and select AM or FM radio band.
    BASIC RADIO OPERATION - Step 1
  2. Press and release the Hour/ Button or Minute/ button to tune radio to a desired station. Press and hold to seek the next clear station.
    BASIC RADIO OPERATION - Step 2 - Tune the radio
  3. Press and release the Volume - Button or Volume + Button to adjust radio volume.
    BASIC RADIO OPERATION - Step 3 - Adjust the volume

PRESET RADIO SETTING AND OPERATION SETTING RADIO PRESETS

This unit will store up to 20 station presets, 10 AM and 10 FM.

  1. Press and release the Power/Mode/Alarm Reset Button as needed to turn unit On and select AM or FM radio band.
    OPERATION SETTING RADIO PRESETS - Step 1
  2. Press and release the Hour / Button or Minute / Button to tune radio to a station you want to assign to a preset. Press and hold to seek the next clear station.
    OPERATION SETTING RADIO PRESETS - Step 2
  3. Press and hold the Clock/Preset Button to enter presetting mode.
    OPERATION SETTING RADIO PRESETS - Step 3
  4. Press and release the Hour / Button or Minute / Button to select the preset number you wish to assign (P01 - P10).
    OPERATION SETTING RADIO PRESETS - Step 4
  5. Press and release the Clock/Preset Button to confirm the preset number (P01 - P10) you want to assign to the current station.
    Continue steps 1- 5 to set all desired presets.

PRESET RADIO OPERATION

To listen to a preset AM or FM station at any time, press and release the Clock/Preset Button as needed to select the desired preset station.

Using Aux In Audio

  1. Connect a standard audio cable with 3.5mm plug (not included) to the AUX IN jack located on the back of the unit and to the output/headphone jack of your audio device.
    Using Aux In Audio - Step 1
  2. Press and release the Power/Mode/Alarm Reset Button as needed to turn unit On and select AUX mode.
    Using Aux In Audio - Step 2
  3. Control audio playback on your device, making sure output volume is turned up. If needed, press the Volume - Button or Volume + Button to adjust volume on the unit.
    Using Aux In Audio - Step 3

Sleep Mode

Sleep mode allows you to set the unit to turn off after a selected time interval. It allows you to fall asleep while listening to the radio or a device that is connected to the Aux In Jack.

NOTE: It will power off the Timex unit, but it will not power off your AUX device.

Press and release the Snooze/Sleep Button in AM/FM or AUX mode to select the desired sleep interval: 90, 80, 70, 60, 50, 40, 30, 20, 10 minutes or OFF (turns unit off right away).
Using the Sleep Mode

Dimmer

Press and hold the Snooze/Sleep Button to toggle display brightness between high and low settings. Dimmer cannot be adjusted when alarm is sounding.
Using the Dimmer

Battery Cautions and Tips

  • Only use the recommended/supplied batteries or equivalent.
  • Use alkaline batteries for longer life.
  • Do not mix old and new batteries, and do not mix alkaline, carbon-zinc or rechargeable nickel-cadmium batteries.
  • Insert batteries with proper polarity (+/–) as indicated.
  • Remove exhausted batteries from product.
  • Recharge rechargeable batteries under adult supervision.
  • Do not attempt to recharge non-rechargeable batteries.
  • Do not open batteries or heat them beyond normal ambient temperatures.
  • To prevent battery leakage or damage remove batteries from a product if it will not be used for a month or longer.
  • Use extreme caution handling leaking batteries (avoid direct contact with eyes and skin). If batteryleakage comes in contact with eyes, IMMEDIATELY flush the eye with lukewarm and gently flowing water for at least 30 minutes. If skin contact occurs, wash skin with clear water for at least 15 minutes. Seek medical attention if any symptoms occur.
  • Store in cool, dry, ventilated area away from hazardous or combustible material.
  • Do not dispose of batteries in the household trash or fire.
  • Follow applicable laws and local regulations for the disposal and transportation of batteries.


RISK OF ELECTRIC SHOCK.
DO NOT OPEN


TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

shock hazard The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user of the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk electric shock to persons.

warning The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

The symbols above are located at the bottom of the cabinet.


To prevent electric shock, do not use this (Polarized) plug with an extension cord receptacle, or other outlets unless the blades can be fully inserted to prevent blade exposure.

IMPORTANT SAFETY INSTRUCTIONS

shock hazardshock hazard
When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit.

  1. Water and Moisture – The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement.
  2. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also, it should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of air through the ventilation openings.
  3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances (including amplifiers) that produce heat.
  4. Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance.
  5. Power-Cable Protection – Power supply cables should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. It is always best to have a clear area from where the cable exits the unit to where it is plugged into an AC socket.
  6. Cleaning – The unit should be cleaned only as recommended. See the Maintenance section of this manual for cleaning instructions.
  7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into any openings or vents located on the product.
  8. Attachments – Do not use attachments not recommended by the product manufacturer.
  9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the antenna or cable system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent damage to the product due to lightning and power-line surges.
  10. burn hazardshock hazard
    Overloading – Do not overload wall sockets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.
  11. Damage Requiring Service – The unit should be serviced by qualified service personnel when:
    1. the power supply cable or plug has been damaged.
    2. objects have fallen into or liquid has been spilled into the enclosure.
    3. the unit has been exposed to rain.
    4. the unit has been dropped or the enclosure damaged.
    5. the unit exhibits a marked change in performance or does not operate normally.
  12. Antenna – Do not connect an external antenna to the unit (other than that provided).
  13. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or longer, the power cable should be unplugged from the unit to prevent damage or corrosion.
  14. Servicing – The user should not attempt to service the unit beyond those methods described in the user's operating instructions. Service methods not covered in the operating instructions should be referred to qualified service personnel.

Troubleshooting

The unit does not power ON

The unit is not connected to AC outlet, the AC outlet has no power, or is controlled by a wall switch that is "OFF". Check AC outlet and wall switch.

Alarm does not come on

The alarm time AM or PM incorrectly set, Alarm was OFF, etc. Check alarm settings.

Low battery indicator is on

Batteries have not been installed correctly in the battery compartment or the batteries may be weak or exhausted. Try replacing batteries.

Poor FM Radio reception on certain stations

Weak or distant station. Try adjusting the direction of the FM wire antenna.

Poor AM Radio reception on certain stations

Weak or distant station. Rotate the unit to improve reception.

Unit shuts "Off" unexpectedly

The unit is in Sleep Mode instead of the power ON mode, the unit was turned ON by an alarm and the alarm time ended, or the AC outlet unit is connected to is controlled by a wall switch that is turned OFF. Check mode on unit. Check wall switch. Turn unit on with Power Button.

FCC Information

This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.


  • Changes or modifications to this unit not expressly approved by the party responsible for compliance couldvoid the user's authority to operate the equipment.
  • NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules.

Limited 90 Day Warranty Information

Timex Audio Products, a division of SDI Technologies Inc. (hereafter referred to as SDI), warrants this product to be free from defects in workmanship and materials, under normal use and conditions, for a period of ninety (90) days from the date of original purchase.

If service is required, please call Customer Service at 1-800-888-4491 for Return Authorization and shipping instructions.

© 2014 SDI Technologies, Inc. All rights reserved
Questions? Visit www.timexaudio.com
or call 1-800-888-4491 Toll Free

TIMEX is a registered trademark of Timex Corporation in the United States and other countries

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Timex T231Y AM/FM Clock Radio Manual

Advertisement

Need Assistance?

Do you have a question about the T231Y that isn't answered in the manual? Leave your question here.

Error while submitting your question. Please, reload page and try again.

Thank you! Your question has been received!

Table of Contents