Advertisement
Power button | |
Call button | |
Charge port | |
Headset LED (indicator light) | |
Volume/Mute button |
The first time you power on your headset, it begins the pairing process.
Multipoint technology lets you pair a second phone and answer calls from either phone.
Your new headset has enough power to pair and make a few calls. It takes two hours to fully charge the headset; the indicator light turns off once charging is complete.
The universal-fit eartip has a thin loop that bends to gently tuck into the contours of either ear.
Answer a call
Choose:
Answer a second call
First, tap the Call button to end current call, then tap the Call button again to answer new call.
End a call
Tap the Call button to end current call.
Reject a call
Choose:
Call back last call
To dial your last number you dialed, double-tap the Call button .
Voice dial (phone feature)
Press the Call button for 2 seconds, wait for phone prompt and then tell the phone to dial the name of a stored contact.
You can mute the microphone during a conversation.
During a call, tap the Volume/Mute until you hear "mute on" or "mute off." While the microphone is muted, an alert repeats every 15 minutes.
Tap the Volume/Mute button to cycle through preset levels.
Streaming audio is controlled using your phone, but when a call rings, the audio automatically pauses to allow you to answer or ignore the call. Once the call is ignored or ends, the streaming audio is resumed.
If you leave your headset powered on but out of range of your paired phone for more than 90 minutes, your headset will conserve its battery power by entering into a DeepSleep mode.
Once back in range with your phone, tap the Call button to exit DeepSleep mode. If your phone is also ringing, tap the Call button again to answer your call.
Your headset has an indicator light that flashes in response to a change in status or after a button press. Some examples of what you will see are:
Your headset tells you about status changes in English. For example:
This headset only speaks and understands English. If you prefer to use the Call button to answer or reject calls, you can disable the voice commands "answer" or "ignore."
With the headset powered on, simultaneously press the Call and Volume buttons until you see the indicator light flash white two times. Repeat these steps to reactivate the commands.
Talk time | Up to 7 hours* |
Standby time | Up to 11 days* |
Headset weight | 7 grams |
DeepSleep technology |
|
Multipoint technology | Use one headset to answer calls from either of two paired Bluetooth phones |
Charge connector | Micro USB charging |
Battery type | Rechargeable, non-replaceable lithium-ion polymer |
Charge time (maximum) | 90 minutes for full charge |
Headset battery meter | On-screen for iPhone, enabled by Find MyHeadset ™ |
Bluetooth version | v3.0 |
Bluetooth profiles | Advanced Audio Distribution Profile (A2DP), Wideband Hands Free (HFP) Profile 1.6 and Headset (HSP) Profile 1.2 |
Operating and storage temperature | 32°F – 104°F (0 – 40°C) |
NOTE
* Performance is dependent upon battery and may vary by device.
NEED MORE HELP?
www.plantronics.com/support
Plantronics, Inc. 345 Encinal Street Santa Cruz, CA 95060 United States
Plantronics BV South Point Building C Scorpius 140 2132 LR Hoofddorp, Netherland
© 2012 Plantronics, Inc. All Rights Reserved. Bluetooth is a registered trademark of Bluetooth SIG, Inc. and any use by Plantronics is under license. All other trademarks are the property of their respective owners.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Plantronics Marque 2 M165 - Bluetooth Headset Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the Marque 2 that isn't answered in the manual? Leave your question here.