Scotsman Prodigy Plus A Series Service Manual
Remote low side modular flake ice machine
Hide thumbs
Also See for Prodigy Plus A Series:
- Service manual (49 pages) ,
- Installation and user manual (20 pages)
Related Manuals for Scotsman Prodigy Plus A Series
Summary of Contents for Scotsman Prodigy Plus A Series
- Page 1 Service Manual for Remote Low Side Modular Flake Ice Machine Prodigy Plus A Series Model FS2330L...
-
Page 2: Table Of Contents
Scotsman flaked ice system to provide reliable ice making and the features needed by customers. Contents Installation: . -
Page 3: Installation
Minimum Maximum situation. Testing has shown that using a filter that does not remove chlorine, such as the Scotsman 208-230 60 Hz Aqua Patrol, will greatly improve this situation. Minimum conductivity (RO water) Warranty Information •... -
Page 4: Location
24 inches deep. Confirm available space when approved by Scotsman. replacing a prior model. Scotsman reserves the right to make design changes Bin & adapter list: and/or improvements at any time. Specifications and design are subject to change without notice. -
Page 5: Cabinet Layout
FS2330L Remote Low Side Service Manual Cabinet Layout December 2022 Page 4... -
Page 6: Unpacking & Install Prep
FS2330L Remote Low Side Service Manual Unpacking & Install Prep Remove the carton from the skid. Check for hidden Panel Removal freight damage, notify the carrier immediately if any is found. Retain the carton for the carrier’s inspection. The machine is not bolted to the skid. If strapped remove the strap. -
Page 7: Water
FS2330L Remote Low Side Service Manual Water Water Supply Attach Tubing The water supply for ice making must be cold, potable Connect the potable water supply to the potable water water. There is a single 3/8” male flare potable water fitting, 3/8”... -
Page 8: Electrical
FS2330L Remote Low Side Service Manual Electrical The machine includes a power cord, connect to the proper power supply. A separate circuit is recommended to avoid unintended shut downs. If a dedicated condensing unit is connected to this machine, it will have a separate power supply. Do not use an extension cord. -
Page 9: Refrigeration
FS2330L Remote Low Side Service Manual Refrigeration BTUH Capacity Requirements Connections Model BTUH The liquid and suction fittings on the back of the cabinet are stubs. The liquid line size is 3/8" OD. The FS2330L-32A 12,000 suction line size is 5/8" OD. Remote low side models require connection to a 1. -
Page 10: Final Check List
FS2330L Remote Low Side Service Manual Final Check List After connections: into the cabinet and cause serious damage. Damage caused by foreign material is not covered by warranty. 1. Wash out the bin. If desired, the interior of the bin could be sanitized. -
Page 11: Initial Start Up And Maintenance
FS2330L Remote Low Side Service Manual Initial Start Up and Maintenance Startup • All models need scale removed from the water system. 1. Turn the water supply on. Remote models also open the liquid line valve. • All models require regular sanitization. 2. -
Page 12: Maintenance: Scale Removal And Sanitation
Scale Removal Note: Following this procedure will reset the de-scale and sanitize light. 11. Prepare a solution of 32oz. Scotsman Clear One™ scale remover and 32oz. 95-115 °F. potable water. Preparing to Clean 12. Using a small cup for precise pouring, add the 1. -
Page 13: Maintenance: Sensors
FS2330L FS2330L Remote Low Side User Manual Remote Low Side Service Manual Maintenance: Sensors Photo Eyes Water Probe The control that senses bin full and empty is a photo- The ice machine senses water by a probe located electric eye, therefore it must be kept clean so it near the water reservoir. -
Page 14: Controller
FS2330L Remote Low Side Service Manual Controller Location of Optional Vari-Smart (KVS) Code Description ..Freeze Mode flashes . . Freeze Mode is Pending ..Bin is Full Clean . -
Page 15: Component Indicator Lights
FS2330L Remote Low Side Service Manual Component Indicator Lights Control Button Use The controller has six lights to indicate component operation: Recall diagnostic code: Auger Left • Hold off button in for 3 seconds. Release. • This light is ON when the left auger motor is •... -
Page 16: Autoalert And Display Code
FS2330L Remote Low Side Service Manual AutoAlert and Display Code The controller uses indicator lights to provide the user Code Description with information on Power, Status, Water or Time to ..Freeze Mode Clean. -
Page 17: Remote Refrigeration With Condensing Unit Or Rack
FS2330L Remote Low Side Service Manual Remote Refrigeration with Condensing Unit or Rack A condensing unit's compressor concentrates the heat The EPR valve in the ice machine keeps the suction from ice making into high pressure, hot discharge gas. pressure at the correct pressure, regardless of a lower The high pressure forces the gas to the condenser. -
Page 18: Electrical Component Details
FS2330L Remote Low Side Service Manual Electrical Component Details Liquid line valve • Opened by the controller to start ice making. • Closed to shut unit off. Line voltage coil. Controller • Senses water, ice making, and auger amps. • Controls liquid line solenoid coil and auger motor. •... -
Page 19: Sequence Of Operation
FS2330L Remote Low Side Service Manual Sequence of Operation The ice machine’s function is to continuously produce Additionally, the control system uses the photo-eyes ice until the ice level control senses that there is to confirm ice making. As the machine makes ice, enough ice in the bin or dispenser. -
Page 20: Electrical Sequence
FS2330L Remote Low Side Service Manual Electrical Sequence Pushing and releasing the On button starts the machine. The sequence of operation begins with water. Water must be sensed or the controller will not start the ice making process. If there is no water, a 3 will show it the code display. -
Page 21: Water System
FS2330L Remote Low Side Service Manual Water System Water enters the machine through the 3/8" male flare The correct level should be between 1/8” above and at the rear of the cabinet, goes to the water reservoir 1/4” below the line. If needed, bend the float arm up which it enters through the float valve. -
Page 22: How Ice Is Made
FS2330L Remote Low Side Service Manual How Ice Is Made Refrigeration effect is applied to the water between Flaked ice machines have 6 oblong and curved slots the auger and the evaporator. When that water's that ice flows from, and they produce a softer, wetter temperature drops to its freezing point, ice crystals ice form. -
Page 23: Options
FS2330L Remote Low Side Service Manual Options Vari-Smart Use of Adjustable Ice Level Control Optional adjustable ice level control (KVS). When There are several positions the ice level can be set to, this option is present there is an adjustment post and including Off or Max (knob and label indicators lined an additional indicator light to the right of the four up), where it fills the bin until the standard bin control... -
Page 24: Service Diagnosis
FS2330L Remote Low Side Service Manual Service Diagnosis Symptom Probable Cause Possible Correction No ice No power Check that ice machine and condensing unit, if used, both have power. If power light is out, check transformer. Code 3: No water Restore water Status light is off Push and release ON switch... -
Page 25: Repair Procedures: Bearing And Extruder
Extruder: Top Bearing: 1. Remove panels and disconnect electrical power. Note: Scotsman service recommends changing BOTH top and bottom bearings if one must be changed. 2. Turn off the water to the machine, and unclip the evaporator drain hose, pull it down and drain the 1. - Page 26 FS2330L Remote Low Side Service Manual Bottom Bearing Bottom Bearing: 5. Separate the gear reducer, evaporator and bearing retainer. 1. Go thru the process of removing the auger. 6. Remove the clip. 2. Remove the foam wrap at the bottom of the evaporator.
-
Page 27: Auger And Evaporator Inspection
FS2330L Remote Low Side Service Manual Auger and Evaporator Inspection The auger must be carefully inspected for wear and scale. The wear areas are the top bearing surface, drive junction and the edges of the flights. The edges of the auger have horizontal serrations and there are highly machined areas in between. -
Page 28: Water Seal
Note: The bottom bearing should have been replaced bead of food grade sealant to the bottom of the at this time. (see page 25) auger. (732 RTV or Scotsman part number 19- 0529-01) 10. Secure the evaporator to the bearing retainer with the original socket head screws. -
Page 29: Repair Procedures: The Gear Reducer
FS2330L Remote Low Side Service Manual Repair Procedures: The Gear Reducer Note: The high speed non-metallic fiber gear is the 5. After the gear case is together, replace all cap only internal part that is a service part and can be screws. -
Page 30: Repair Procedures: Replace The Evaporator
FS2330L Remote Low Side Service Manual Repair Procedures: Replace the Evaporator (Assuming all the steps for removal of the bearings, extruder, auger, and water seal have been performed.) 1. Recover the refrigerant from the ice maker. 2. Unsweat the refrigerant connections: a) At the thermostatic expansion valve outlet. - Page 31 SCOTSMAN ICE SYSTEMS 101 Corporate Woods Parkway Vernon Hills, IL 60061 800-726-8762 www.scotsman-ice.com...