Advertisement
IMPORTANT!
The product is not intended to be used or cleaned by
persons with reduced physical, sensory, or mental
capabilities, or lack of experience or knowledge, unless
they have been given instructions concerning the safe
use of the product by a person legally responsible for
their safety. They should be supervised while using the
product. Children shall not use, clean, or play with the
product, which when not in use, should be secured out
of their reach.
It is essential that you read the instructions in this manual
before assembling, operating, and maintaining the
product.
Subject to technical modification.
Safety, performance, and dependability have been given top
priority in the design of your battery charger.
INTENDED USE
This charger is intended to charge only BPL3620D,
BPL3640D2,
BPL3660D,
BPL3650D2, R36BTY2, R36BTY4, and R36BTY5 battery
packs listed in this manual.
The product is only for indoor use, in dry conditions.
The product is not intended to charge any other type of
battery or be used as a power supply. It should never be
used in explosive or flammable environments.
Do not use the product for any other purpose.
CHARGER SAFETY WARNINGS
WARNING! Do not recharge primary cells (non-
rechargeable).
■
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, fire, and/or serious injury.
■
Mains voltage must correspond with the voltage
specifications on the product.
■
Before using the product, check that the charger
enclosure, cable, and plug are not damaged. If damage
is found, do not use the product and bring it to an
authorised service centre for repair.
■
The product must not be damp and should never be
used in a damp environment.
■
The product is for indoor use only.
■
Do not use the product if it has suffered any heavy shock
or jolting, or if it is damaged in any other way.
■
When charging, do not expose the product to sunlight
or other heat source. The recommended temperature
range at charging vicinity is 10° to 25°C.
■
Due to the heat generated during charging, do not use
the product on a combustible surface.
■
Do not use the product near flammable materials,
such as cloth, packaging materials, paint, spray paint
or aerosols, lubricants, thinners, petrol containers, gas
containers, or gas appliances.
■
Do not cover any ventilation slots, and provide adequate
ventilation during operation.
■
Never modify, disassemble, or attempt to repair the
product yourself.
■
Do not allow the charger or battery packs to become
contaminated with any material that could be conductive,
2
Original Instructions
BPL3690D,
BPL3612D,
such as metallic particles from grinding, cutting, or
machining processes.
■
Unplug the product from the power socket when it is not
in use or when cleaning it.
■
Use only an extension cable that is approved and in
good condition.
■
Do not charge battery packs that show signs of leaks.
Dispose of them properly.
■
Never charge a damaged battery pack. Replace
damaged battery packs immediately.
■
Before every use, examine the supply cord for damage.
If there are signs of damage, it must be replaced by a
qualified person at an authorised service centre to avoid
a hazard.
■
Electrical power should be supplied via a residual
current device (RCD) with a tripping current of not more
than 30 mA.
ADDITIONAL BATTERY SAFETY WARNINGS
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your tool,
battery pack or charger in fluid or allow fluid to flow inside
them. Corrosive or conductive fluids, such as seawater,
certain industrial chemicals, and bleach or bleach-containing
products, etc., can cause a short circuit.
WALL MOUNTING
See Fig. 4
■
Carefully select a stable wall for mounting the charger.
Make sure that there is no hindrance to mounting work
or operation. The maximum gross weight of the charger
is approximately 9.7 kg, provide sufficient reinforcement
for the wall if necessary.
■
Mount the charger in a vertical or horizontal orientation
only. Install two screws on the wall to mount the charger.
Otherwise, the charger may fall and cause serious injury.
■
Check the tightness of the screws on a regular basis.
Make sure that the head of the screws fit properly in
the wall mounting holes to hold the charger firmly in
place. Otherwise, the charger may fall because of loose
screws.
OPERATION
See Fig. 5
CHARGING THE BATTERY PACK
■
Battery packs are shipped in a low charge condition.
Therefore, you should charge them before first use.
If the charger does not charge the battery pack under
normal circumstances, bring both the battery pack and
charger to an authorised service centre.
■
Make sure that the power supply is normal household
voltage, 220–240V, 50/60Hz, AC only.
■
Make sure that the battery pack latch clicks into place
and that the battery pack is secured in the charger
before charging.
NOTE: The charger recharges the battery packs at each
port one at a time, from the port closest to the power cord
connector to the farthest port. If a battery pack is currently
charging and additional battery packs are inserted, the
charger completes recharging the first battery pack before
recharging the additional battery packs.
Advertisement
