Advertisement
PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
SAVE THESE INSTRUCTIONS
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS SAFETY FEATURE IN ANY WAY.
Your heater comes with a remote control, unpack the remote control from box. This unit requires 2 AAA batteries, 1.5V (not included). Please note this remote control will not work through walls. Remove battery before discarding the remote.
Battery Replacement
NOTES:
Potential for Radio/Television interference
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If the product does cause harmful interference to radio or television reception, which can be determined by turning the product on or off, the user is encouraged to try to correct the interference by one or more of the following measures:
NOTE: This unit is for FLOOR USE ONLY.
Eco-Smart™ setting
Press the Power Button () to activate the Eco-Smart™ setting. The heater will now cycle between high and low temperatures to provide heat.
To shut off the heater, press the Power Button () again until all temperature lights are off.
NOTE: The Power Light will remain illuminated while unit is plugged in.
Thermostat Control
Your heater is equipped with a digital thermostat that allows you to set your heater to a precise comfort level (65°F-85°F) by pressing either Up () or Down () button to activate the digital thermostat mode. Press the Up/Down buttons on the control panel or remote control to select your desired temperature level. The higher temperature is selected, the more temperature indicator lights will illuminate. When you continuously press the Up button, all temperature lights will illuminate to indicate the maximum temperature (85°F) is selected. When the preset temperature is reached, the heater will cool down by blowing cool air for 60 seconds, the power light will flash during the cool down period, and then the heater will shut off. When the room temperature drops below the preset temperature, the heater will automatically turn on again to maintain the preset temperature level.
NOTE: It is normal for the heater to cycle ON and OFF as it maintains the preset temperature. To prevent the unit from cycling, you need to change the thermostat setting. The digital thermostat has memory; it will remember the last temperature setting before the heater is turned off. However, if the heater is unplugged, the digital thermostat will no longer remember the previous temperature setting. You will need to reset the digital thermostat if the heater is unplugged.
Always unplug the heater before cleaning and allow the heater to cool down.
This heater is equipped with a patented, technologicallyadvanced safety system that requires the user to reset the heater if there is a potential overheat situation. When a potential overheat temperature is reached, the system will automatically shut the heater off to indicate overheat situation. It can only resume operation when the user resets the unit.
If your heater shuts down:
Troubleshooting for your Heater | ||
Trouble | Probable Cause | Solution |
| Manual user reset is activated. Not plugged in properly. Electrical outlet does not hold plug in securely. Thermostat set too low. Obstruction causing the heater not to operate. Circuit breaker trips. | Follow reset instructions listed in this manual. Ensure plug is properly inserted. Make sure electrical outlet and circuit breaker are working. Have outlet replaced by a licensed electrician. Press the Up Button to select the highest temperature setting. Unplug the heater and remove all obstructions. Position your heater 36 inches (91cm) away from all objects. Make sure no other high wattage appliances are operating on the same circuit and reset breaker if needed. |
| Thermostat set too low. | Press the Up Button to the highest temperature setting. |
| The thermostat automatically turns the heater on and off to maintain selected comfort level. | To make this occur less frequently press the Up Button to the highest setting. |
| Battery low. Distance too far. Control Panel Display dirty. | Change battery (2 AAA batteries). Remote works up to 20 feet (6m). Be sure to point remote at control panel on heater and there are no obstructions. Make sure display panel is clean. |
| When the heater is in Thermostat Mode and reaches the set temperature it will automatically perform a 60 second cool down (blowing cold air) to ensure thermostat accuracy. The Power Light will flash during the cool down period. Power Button may have been pressed to turn off the heater. | Raise the temperature higher. Press the Power Button to turn on the heater. |
| Eco-Smart™ control the heat output of the heater and not the fan speed. Fan runs at the same speed on all settings. | Press the Up Button to the highest temperature setting for maximum heat output. |
| You may hear a popping or crackling sound as the heater heats up. This is normal and safe operation. Once the heater heats up, the crackling sound will go away. | If the noise persists, visit our website at www.holmesproducts.com. |
| There may be an odor or vapor coming from the heater the first time you use it or after prolonged or seasonal storage. | This is normal and is the result of dust or other debris accumulating on the heating element. Make sure the heater is in a well ventilated area and continue running until the odor or vapor goes away. |
If you have any questions regarding your product or would like to learn more about other Holmes® products, please visit our website at www.holmesproducts.com. For inquiries regarding recycling and proper disposal of this product, please contact your local waste management facility.
© 2014 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All Rights Reserved.
Distributed by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions, Boca Raton, Florida 33431.
Printed In China
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Holmes HRH6403ERE - Programmable Infrared Quartz Heater Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the HRH6403ERE that isn't answered in the manual? Leave your question here.