Related Manuals for Agilent Technologies Medalist 5DX Automated
Summary of Contents for Agilent Technologies Medalist 5DX Automated
- Page 1 Agilent Technologies Medalist 5DX Automated X-ray Inspection System Operator Instructions...
-
Page 3: Table Of Contents
Contents Emergency Stop Hardware Overview Medalist 5DX Diagram 6 System Light Tower Operator Control Panel 8 Operator Instructions Startup the System 9 Verify the Safety Interlocks are Closed 9 Verify the X-Ray Has Been Enabled 9 Log on to Microsoft Windows XP 9 Log on to the Medalist 5DX User Interface 9 Run Testing 11 End Testing... - Page 4 Operator Instructions...
-
Page 5: Emergency Stop
Emergency Stop 1 Emergency Stop The emergency stop buttons are intended for use in emergency situations only CAUTION and should not be used for normal system shut down. Repeated misuse of the emergency stop buttons will eventually cause damage to certain components or the loss of data or both. -
Page 6: Hardware Overview
2 Hardware Overview Medalist 5DX Diagram The Medalist 5DX Automated X-ray Inspection System provides a comprehensive test and inspection process to discover solder defects on a circuit board. Figure 1 Medalist 5DX system System controller Emergency stop (EMO) button Panel handler access door... -
Page 7: System Light Tower
Hardware Overview System Light Tower The system light tower is permanently attached to the electronics cabinet. The system light tower is used to visually indicate the operating condition of the Medalist 5DX. Figure 2 System light tower Buzzer — If enabled, sounds when there is a hardware failure. Red Lamp —... -
Page 8: Operator Control Panel
Operator Control Panel The operator control panel provides an X-ray Control key and X-ray control buttons as well as status LEDs (see Figure 3). It is attached to the keyboard tray. Figure 3 Operator control panel X-ray Control key (Enable (1)/ Disable (0)) X-ray Control enable button X-ray Control disable button X-rays LED... -
Page 9: Operator Instructions
Operator Instructions 3 Operator Instructions Startup the System The Medalist 5DX is operated through the use of a user interface running on the system controller. Before starting the system software, verify that the X-ray has been enabled. Verify the Safety Interlocks are Closed On the operator control panel (see Figure 3) verify that the Safety... - Page 10 The system will perform a system startup. This may take a few minutes (see Figure Figure 5 Startup progress Operator Instructions...
-
Page 11: Run Testing
Operator Instructions Run Testing Depending on how the software has been set up, you may be asked to choose the project to load. If prompted, select the appropriate project and click OK (see Figure 6). If not, continue with Step 2. Figure 6 Enter project pop-up Depending on how the software has been set up, you may be... - Page 12 Figure 8 Load the panel into the machine Once a panel is loaded, the inspection will begin. Figure 9 Inspection in progress Operator Instructions...
-
Page 13: End Testing
Operator Instructions When the inspection is finished, the panel will automatically be unloaded and the system will wait for the panel to be removed from the machine. After the panel is removed, continue repeating steps 2 and 3 until testing is complete. End Testing To exit the Medalist 5DX user interface: Press Cancel at the serial number prompt. -
Page 14: What To Do In Case Of A Problem
4 What to do in Case of a Problem Panel Retrieval Occasionally it is necessary to enter into the 5DX Cabinet to retrieve a dropped or jammed panel. The Medalist 5DX will display an error message if panel retrieval is necessary. Figure 11 shows the error message that can occur when trying to load a panel:... -
Page 15: Other Errors
What to do in Case of a Problem Reach in and remove the panel. Close and lock all access panels. If you are unable to easily remove the panel, the panel clamps may be locked in NOTE the down position, or the panel in place sensor may be extended. Ask a service technician for assistance. - Page 16 © Agilent Technologies, Inc. 2008 Printed in Malaysia June 2008 N7200-90090 Rev. A...