Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for NETGEAR FE116
Summary of Contents for NETGEAR FE116
- Page 1 MODEL Fast Ethernet Hub Installation Guide...
-
Page 2: Start Here
(UTP) wiring (The network ports on the Model FE116 hub are referred to as vista RJ-45 network ports because they have built-in LEDs that monitor individual port status.) •... -
Page 3: Package Contents
To qualify for product updates and product warranty registration, complete the Warranty & Owner Registration Card within 30 days of purchase and return it to NETGEAR, Inc. Model FE116 Fast Ethernet Hub Installation Giude Power... - Page 4 Product Illustration Start Here The instructions provided in this guide are for installing and using the Model FE116 hub. Front Panel of the Model FE116 Hub Pwr LED FE116 100BASE-FAST ETHERNET HUB Col LED LEDs There are two LEDs on the front panel of the hub and two on each vista 100BASE-T network port (RJ-45 connector) that allow you to monitor the status of the hub and the network.
- Page 5 Rear Panel The rear panel of the Model FE116 hub has a DC power jack and a ground clip (not used). The Model FE116 hub accepts 5 V DC. Rear Panel of the Model FE116 Hub 100 BASE-TX Class Ground clip Model FE116 Fast Ethernet Hub Installation Giude 5Vdc 3.0A...
-
Page 6: Installation Procedures
Install the Hub Place the Model FE116 hub on a flat surface or mount it on a wall with the hardware included in the wall mount kit. Be sure the hub is positioned with at least 2 inches of space on all sides for ventilation. -
Page 7: Connect A Pc To The Hub
(100BASE-TX networks require only 2-pair wiring). The RJ-45 interface is an 8-pin connector. To connect any of the RJ-45 ports on your Model FE116 hub to a PC, use a regular straight- through UTP cable. If you are connecting using Port 16 on your hub, set the Normal/Uplink push button to Normal. -
Page 8: Connect The Hub To A Network
Connecting Device Model FE116 Hub Port 16 set to Normal PC or server Port 16 set to Uplink Hub, router, or switch Model FE116 Fast Ethernet Hub Installation Giude Cable Used Straight-through cable Crossover cable Cable Used Straight-through cable Straight-through cable... - Page 9 100BASE-FAST ETHERNET HUB FE116 100 Mbps Link/Rx Part Normal/Uplink Model FE116 hub FE116 100 Mbps 100BASE-FAST ETHERNET HUB Model FE116 Fast Ethernet Hub Installation Giude FE116 100 Mbps 100BASE-FAST ETHERNET HUB Link/Rx Part Normal/Uplink FE116 100 Mbps 100BASE-FAST ETHERNET HUB...
-
Page 10: Verify The Installation
Verify the Installation To complete the installation, connect the power adapter first to the power jack on the hub rear panel and then to the power outlet on the wall. When power has been applied to the hub: • The green Pwr (power) LED on the front panel is on. -
Page 11: Troubleshooting Information
Troubleshooting Information Refer to this table and the information that follows the table to troubleshoot your Model FE116 hub. Symptom Cause Amber Col Data collision is (collision) LED normal on blinks. Ethernet networks. Amber Col LED There is data blinks excessively. - Page 12 The most popular cabling scheme in an Ethernet network today is star-wired topology, where the hub is in a central wiring closet and individual cables run out to each tabletop device. This topology is the same topology used by Fast Ethernet, although the maximum allowable network diameter is smaller because of the increase in packet speed.
-
Page 13: Technical Specifications
CSA certified (CSA 22.2 #950) TUV licensed (EN 60 950) T-Mark Warranty Information Power adapter Model FE116 Fast Ethernet Hub Installation Giude 100 to 240 VAC, 50 to 60 Hz 5V DC at 3.0 Amps, maximum 13 W 11.2 inches (28.5 cm) 1.1 inches (2.8 cm) - Page 14 Certificate of the Manufacturer/Importer It is hereby certified that the Model FE116 Fast Ethernet Hub has been suppressed in accordance with the conditions set out in the BMPT- AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to certain restrictions.
-
Page 15: Customer Support
New Zealand: 800-444-626 Korea: 00308-11-0319 Sweden: 020-790086 Internet/World Wide Web The NETGEAR web page is at http://NETGEAR.baynetworks.com Bulletin Board Service You can contact the bulletin board service at 407-531-4574 to download the latest version of the software driver for the network card.