Table of Contents
Advertisement
Available languages
Available languages
♦
Check that the cutting line does not protrude more than
approximately 136mm from the spool. If it does, cut it off
so that it just reaches the line trimming blade.
POWERCOMMAND feed does not work
♦
Remove the spool cap.
♦
Pull the cutting line until it protrudes approximately
136mm from the spool. If insufficient cutting line is left
on the spool, install a new spool of cutting line.
♦
Ensure that the line is not crisscrossed on the spool as
detailed in Fig. T. If it is, unwind the cutting line, then
wind it back on the spool neatly so that the lines do not
cross.
♦
Ensure the beginning of the cutting line is pulled tight
against the spool as shown in Fig. S.
♦
Align the tabs on the spool cap with the cut outs in the
housing.
♦
Push the spool cap onto the housing until it snaps
securely into place.
♦
If the cutting line protrudes beyond the trimming blade,
cut it off so that it just reaches the blade.
If the POWECOMMAND line feed still does not work or the
spool is jammed, try the following suggestions:
♦
Carefully clean the spool and housing.
♦
Remove the spool and check if the lever in the spool
housing can move freely.
♦
Remove the spool and unwind the cutting line, then wind
it on neatly again. Replace the spool into the housing.
Maintenance
Your BLACK+DECKER corded/cordless machine/tool
has been designed to operate over a long period of time
with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool/machine care and
regular cleaning. Your charger does not require any
maintenance apart from regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
♦
Switch off and unplug the machine/tool.
♦
Or switch off and remove the battery from the machine/
tool if the machine/tool has a separate battery pack.
♦
Or run the battery down completely if it is integral and
then switch off.
♦
Unplug the charger before cleaning it. Your charger
does not require any maintenance apart from regular
cleaning.
♦
Regularly clean the ventilation slots in your tool/machine
and charger using a soft brush or dry cloth.
♦
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
♦
Regularly clean the cutting line and spool using a soft
brush or dry cloth.
♦
Regularly use a blunt scraper to remove grass and dirt
from the underneath of the guard.
Protecting the environment
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw
materials.
Please recycle electrical products and batteries according
to local provisions. Further information is available at
www.2helpU.com
Technical data
BESTE625
Type 1
Voltage
V
230
AC
Power Input
W
450
No-Load
min
7500
-1
Speed
Weight
kg
2.5
BESTE625 Level of sound pressure:
Sound pressure (L
) 80 dB(A), uncertainty (K) 3 dB(A)
pA
Sound power (L
) 93 dB(A), uncertainty (K) 2.6 dB(A)
WA
BESTE625 Vibration total values (triax vector sum)
according to EN 50636-2-91:
Vibration emission value (a
1.7 m/s
2
BESTE628 Level of sound pressure:
Sound pressure (L
) 81 dB(A), uncertainty (K) 3 dB(A)
pA
Sound power (L
) 94 dB(A), uncertainty (K) 1.1 dB(A)
WA
BESTE628 Vibration total values (triax vector sum)
according to EN 50636-2-91:
Vibration emission value (a
1.7 m/s
2
BESTE630 Level of sound pressure:
Sound pressure (L
) 80 dB(A), uncertainty (K) 3 dB(A)
pA
Sound power (L
) 93 dB(A), uncertainty (K) 2.6 dB(A)
WA
BESTE630 Vibration total values (triax vector sum)
according to EN 50636-2-91:
Vibration emission value (a
1.7 m/s
2
ENGLISH
BESTE628
BESTE630
Type 1
Type 1
230
230
550
550
7500
7500
2.5
2.5
) 4.4 m/s
, uncertainty (K)
2
h
) 4.7 m/s
, uncertainty (K)
2
h
) 4.9 m/s
, uncertainty (K)
2
h
15
Advertisement
Table of Contents
