Advertisement
Quick Links
Advertisement
Summary of Contents for Sirius Satellite Radio Ursa Major
- Page 1 ζ URSA MAJOR 产品使用说明 Product Introduction SIRIUS Produced Anti-flex Associated...
- Page 2 开箱 Unboxing 本次键盘为军火箱发货 Customized suitcase is provided for delevery.
- Page 3 打开箱子，可见假组状态的键盘本体（左右俩部分）、配件 以及 透明底座（如果选购） The keyboard is soft-assembled, while separately located on two sides (left and right). In the middle space, Accessories and the pedestal (if purchased) would be found. 如选购了额外 彩色装饰铝合金选件 或 内胆，取出键盘本体， 抽离中层缓冲垫，额外购买物可见于仓体底部。 Additional color decorative aluminum accessories and PCB suits can be seen under thr keyboard, when taken out the keyboard and middle cushion.
- Page 4 配件包含以下：（其中 a、b、c 为内胆组装必须品） The accessories contain: ( notice a, b, and c are necessary to provide essential function) a. 白色二脚灯珠 *4 White two-leg lamp bead * 4 b. 尼龙滚轮组件 *1 Nylon roller component*1 c. 信号增强天线 *2 Signal Booster Antenna*2 d. 脚贴 *8（圆形 *4+ 长条形状 *4） Feet stickers*8 (round shape*4+long shape*4) e.
- Page 5 拆解 Disassembling 键盘需要先拆离假组状态，建议过程如下： In order to properly cancel the soft-assembling, following steps is suggested: Step 0: 取出测试触发功能 Test PCB trigger function 键盘开发由 LNE 工作室完成，建议使用官方软件 LINK 进行管理 The keyboard development is completed by LNE Studio, and it is recommended to use the official software LINK for management. NOTE: 产品默认左手部分与...
- Page 6 Step 1: 转至背面 Turn to the bottom side Step 2: 取下底部螺丝 x10（沉头内六角 M2*14 ~M2*16） Remove the bottom screw x10 (countersunk hex socket screw M2 * 14~M2 * 16)
- Page 7 Step 3: 打开键盘，解开排线（建议解开 PCB 位置的接口） Open the keyboard and unlock the cable (recommended to unlock the interface at the PCB side) NOTE: 由于运输要求， 海外版不含电池 （诺基亚 BL5J*2） ， 需自行购买。 Due to the transportation requirements, the overseas version does not include batteries (Nokia BL5J * 2), which should be purchased locally 电池小板固定（沉头内六角...
- Page 8 Step 4: 取下左右手各自的螺丝 X6（沉头内六角 M2*5/M2*6） Remove the screws X6 (countersunk hexagonal socket M2 * 5/M2 * 6) on both left and right side. Step 5: 得到内胆后，拆除卡扣件，准备进行组装。 After obtaining the core, remove the fasteners and prepare for further assembly work.
- Page 9 Step 6: 展开后可见配件：定位板、夹心棉、PCB, 并开始进行组装。 Parts visible after expansion: positioning plate, sandwich cotton, PCBs 请确保 PCB 与定位板 使用 天线（配件 c）进行连接，否则将影响信号。 Please ensure that PCB and positioning plate are connected by accessory c, otherwise, the signal would be unstable. 左手 PCB 使用灯珠（配件 a）进行焊接。 右手...
- Page 10 焊接要点提示 Key points for welding and assembly 本品使用定位板卫星轴，可以从定位板开始，安装轴体和卫星轴并调试。 This product uses the positioning plate satellite. You can start from the plate, install the switch and satellite and adjust them. 灯珠长脚为正极，可根据 PCB 上标记进行安装。 确认无误后进行焊接工作，焊接完成后可以剪除多于的针脚。 The lamp bead long pin is a positive pole, which can be installed referencing to the marks on the PCB.
- Page 11 重新组装 Reassembling Step 0: 将焊接完整的内胆 与 彩色中框 放置于上盖。 Place the completed core and colored middle frame on the top sheld. Step 1: 安装左右手各自的螺丝 X6（沉头内六角 M2*5/M2*6） Install the screws X6 (countersunk hexagonal socket M2 * 5/M2 * 6) on both left and right side.
- Page 12 Step 3: 连接底壳的排线 Connecting the cable from the bottom shell Step 4: 合盖上下壳 Close the top and bottom shells NOTE: 确保排线连接正常再锁螺丝 ; 合盖过程中避免外壳侵压供电排线。 Ensure the cable is connected properly and then lock the screws; Avoid the shells from invading and pressuring the cable during the closing process. Step 5: 安装底部螺丝...
- Page 13 使用 Using 使用场景分为 全无线模式 及 有线模式： The usage scenarios had two mode : full-wireless mode and wired mode 全无线模式 full-wireless mode 将左手、右手电源拨至 ON 位置，与 PC 蓝牙配对即可达成。 Turn “ON” the left-hand and right-hand power supply, and link it with PC's Bluetooth. 此模式下，左右手均依靠电池小板供电。...
- Page 14 使用 Using 与 PC 进行蓝牙匹配，操作如下： Turn on the battery power of both hands and connect the PC with Bluetooth matching. The operations are as follows:...
- Page 15 使用 Using 键盘组装完成后请接线使用 lne link 进行管理， 软件包含 windows 及 mac 支持，下载地址：https://www.lnelab.com/ After the keyboard is assembled, please use the Type-C cable and the software LINK for management, The software includes Windows and Mac support. Download address: https://www.lnelab.com/...
- Page 16 键值设置 Key value settings 蓝牙设置 Bluetooth settings...
- Page 17 SIRIUS Produced Anti-flex Associated THANKS FOR UR SUPPORT 感谢您的支持...