Advertisement
Quick Links
Important Safety Instruction
CAUTION: Use of controls or adjustments or performance of procedures other than those specified
R R
herein may result in hazardous radiation exposure.
Disconnect the apparatus from the mains if it is not in use.
Please study this manual carefully and always keep it available. There are, however, some installa-
tion and operation precautions which you should be aware of.
(1). Read these instructions.
(2). Keep these instructions.
(3). Heed all warnings.
(4). Follow all instructions.
(5). Do not use this apparatus near water.
(6). Clean only with dry cloth.
(7). Do not block any ventilation openings-Maintain well ventilated conditions around the product. Do not put
product on bed, sofa or anything that blocks ventilation. Install in accordance with the manufacturer's
instructions.
(8). Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
(9). Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
(10). Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus. Power supply cords should be routed so that they
are not likely to be walked on or pinched by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
(11). Only use attachments or accessories specified by the manufacturer. Do not use attachments not
TF-DVD7005
recommended by the product manufacturer as they may cause hazards.
(12). Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
(13). Unplug this apparatus during lightning storms or when unused for long periods of time. Unplug it from
the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due
to lightning and power line surges.
(14). Power sources-this product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your home, consult your product dealer
or local power company. For products intended to operate from battery power, or other sources, refer
to the operating instructions.
Please read this manual before connection and use.
(15). Overloading-do not overload wall outlets, extension cords, or integral convenience receptacles as this
can result in a risk of fire or electric shock.
Customer Service Hours
Monday- Friday 8:00AM ~ 11:00PM (EST) 1-800-681-2629 or 718-416-3197
Monday- Friday 6:30PM ~ 11:00PM (EST) 1-800-727-3592
Saturday- Sunday 9:00AM ~ 11:00PM (EST) 1-800-727-3592
Or Send E-Mail to: Customerservice@cobyusa.com / techsupport@cobyusa.com
Unpacking
Note on Disc
Please make sure the following items are included with your DVD player. If any items are
Disc Requirement
missing, contact your dealer.
The DVD player can play back the following discs.
Disc mark
Contents
Disc size
Maximum playback time
133 min (SS-SL)
DVD video
Audio+Video
242 min (SS-DL)
12cm
discs
(moving picture)
266 min (DS-SL)
484 min (DS-DL)
Audio
CD
12cm/8cm
74min/20min
Audio
12cm
600min
MP3
Battery
JPEG
Still high resolution
600min
LCD
Mode
In addition, this unit can play back a CD-R, or CD-RW that contains audio titles or MP3 files.
Main Unit
other than those listed above.(CD-ROM, CD-Extra, CD-G, and CD-l discs can not be played on this DVD player.)
Mute
Care of Disc
Video disc contains high-density compressed data that needs proper handling.
Clear
Step
Hold the disc with fingers. Hold the disc's outer edge and/or the center spindle hole.
Do not touch the disc surface.
DC Car Cord
Remote Control
Do not bend or press the disc. Do not expose the disc to direct sunlight or heating sources.
AC/DC Adapter
Power Cord
Store discs in cabinet vertically, and in dry condition. Prevent exposure to :
Direct sunlight
Heat or exhaust from a heating device.
Extreme humidity.
Clean the disc surface with a soft, dry cleaning cloth. Wipe the disc surface gently and radically from center
toward the outer edge.Do not apply thinner, alcohol , chemical solvent, or sprays when cleaning. Such
cleaning fluids will permanently damage the disc surface.
RCA Cable
Headphones
.1.
.2.
Connections
Connections
Connecting to a Headphone
Be sure that your unit is at low volume level before
Power Connections (to Battery Pack)
connecting the headphone.
**For new or exhausted rechargeable battery pack, we recommend it be recharged for 4 hours.
Increase the volume gradually for your
comfortable listening.
Basic operations on the battery pack
To Headphone jack
a. Place the battery into its cradle and assign the battery hook to the hole.
CAUTION:
b. Hold down the battery to restrain it from spring-up, meanwhile, slide it to arrow direction to lock it .
Hearing experts advise against the constant use
c. To charge the battery pack, attach the battery pack to the main unit and power on the player
of personal stereos played at high volume.
by AC adapter.
Constant high volume use can lead to hearing loss.
d. To remove the battery pack, hold down PUSH/RELEASE button and counter slide the battery.
If you experience ringing in the ears or hearing loss,
discontinue use and seek medical advise.
Headphone
Power Connections (to AC Adapter)
**Do not connect the power cord until all other connections have been made.
ATTACH
AC adapter:
To DC in jack
This AC adapter operates on
100-240V~~50/60Hz 2A Min
DC OUT: 9V
DC current: 2.0A Min
AC100-240V
(NI-MH Rechargeable Battery Pack)
Power is supplied through the provided appropriative power adapter, one end of which is connected
** The battery can be recharged about 300 times without obvious performance drop. **
to the DC IN jack on the main unit, another to wall outlet with AC100-240V.
Note:
a. If you have difficulty inserting the plug, turn it over and reinsert it.
Note:
b. If the unit will not be in use for long periods of time, disconnect the plug from the outlet.
a. Use the special charger.
c. In order to prolong the operation life, the intervals of continuous power on should be not less
b. Never dispose of in fire or heat up.
than 30s.
c. Do not use in high temperature or near heat sources.
d. Do not open the cover. Refer servicing only to qualified service personnel.
Power Connections (to DC Car Cord)
e. Do not charge up the battery pack while the DVD player is working with the battery pack.
To the DC Jack of Car
f. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent
type.
To the DC 9V In of main unit
Low Battery Detection: The unit will auto stop and turn to STANDBY mode when voltage reaches
Plug the DC Car Cord to the DC in Jack for power supply.
too low.
Note:
a. Please do not plug it to the battery recharge jack.
b. The DC Car Cord is only for in car use.
.7.
.8.
Function Buttons
Function Buttons
Program
To play a disc in a desired sequence.
Subtitle
While playing a DVD disc that contains multiple subtitles, press the SUBTITLE button
NOTE: The Program function is available just as the player is in Navigate Off mode.
Sub-
Title
repeatedly to select the desired language of the viewable subtitle.
Press the PBC button to set Navigate Off.
A DVD disc may contain up to 32 selectable subtitles.
Pro-
gram
Press the Program button to enter the program menu.
The default SUBTITLE language is ENGLISH.
In DVD mode
NOTE:
In some cases, the subtitle language is not changed to the selected one immediately.
When a disc supporting the closed caption is played, the subtitle and the closed caption may
overlap each other on the TV screen. In this case, turn the subtitle OFF.
When the desired language is not selected even after pressing the button several times, it
means that the language is not available on the disc.
or ENTER
CLEAR
Clear
Press the Clear button to cancel the incorrect input in DVD program .
SEARCH
Program
.
Go to a desired section. (A desired Title, Chapter, Time)
Search
Playing DVD
Search by Title/Chapter
a). Press the SEARCH button once,below picture appears:
or ENTER button
b). Press the LEFT/RIGHT direction button to highlight the entry.
Program
.
c). Input the desired title/chapter by numeric keys or use up/down direction button to select.
d). Press the ENTER or PLAY/PAUSE button to execute search.
e). To exit, press SEARCH again.
Search by Time
a). Press the SEARCH button twice, below picture appears:
Second
0 03 30
Minute
Hour
b). Input Second, Minute and Hour information by the numeric keys.
or ENTER
c). Press the ENTER or PLAY/PAUSE button to execute the search.
d). To cancel the incorrect information you have input, press the Clear button.
Program
e). To exit , press SEARCH again.
NOTE: Some discs do not allow program setting.
Playing CD
Search by Time
Setup
Press the SETUP button to enter the player's setup menu.
a). Press the SEARCH button once, below picture appears:
Setup
The SETUP menu allows the viewer to adjust the setting details of the DVD player.
Please read the "Setup Menu" of the manual for further directions on how to use the SETUP
0 03 30
Hour
Second
menu.
Minute
b). Input Second, Minute and Hour information by the numeric keypad.
c). To cancel the incorrect input, press the Clear button.
d). To execute the search, press ENTER or PLAY/PAUSE. To exit , press SEARCH again.
.13.
.14.
Safety Precautions
Table of Contents
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
SAFETY INFORMATION
RISK OF ELECTRIC SHOCK
TABLE OF CONTENTS
DO NOT OPEN
WARNING: SHOCK HAZARD-DO NOT OPEN
AVIS: RISOUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
UNPACKING.............................................................................................................................................................1
. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert
NOTE ON DISC........................................................................................................................................................2
the user to the presence of uninsulated "dangerous voltage" within the product's enclosure
VIEWS OF THE MAIN UNIT...................................................................................................................................3-4
that may be of sufficient magnitude to constitute risk of electric shock to persons.
VIEWS OF THE REMOTE CONTROL.....................................................................................................................5
. The exclamation point within an equilateral triangle is intended to alert the user to the
CONNECTIONS(Connecting to a TV)......................................................................................................................6
presence of important operating and maintenance (servicing) instructions in the literature
CONNECTIONS(
Connecting to a HeadphonePower ..........................................................................................................7
accompanying the product.
Connections (to AC Adapter)Power
Connections (to DC Car Cord)
CONNECTIONS(
Power Connections to Battery Pack).........................................................................................................8
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
Dangerous high voltage is present inside the enclosure. Do not open the cabinet.
FUNCTION BUTTONS...........................................................................................................................................9-14
CAUTION:
To prevent electric shock, match wide blade plug to wide slot, and fully insert.
SETUP MENU.......................................................................................................................................................15-17
CAUTION:
This Digital Video Disc Player employs a laser System. To prevent direct exposure to the
laser beam, do not try to open the enclosure. When open and the interlocks are defeated,
CUSTOM SETUP....................................................................................................................................................17
visible laser radiation is present.
TROUBLE SHOOTING...........................................................................................................................................18
Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure. DO NOT STARE INTO BEAM.
SPECIFICATIONS...................................................................................................................................................19
FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device. Pursuant with
the FCC Rules,Part 15. These limits are designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and if not installed and used in
accordance with the instruction may cause harmful interference to radio communication.
NOTE: 1. Mains plug is used as the disconnect device. It shall remain readily operable and should not
be obstructed during intended use.
2. The rating label is located on the bottom enclosure of the apparatus.
Views of the Main Unit
Views of the Main Unit
Main Unit
Main Unit
TFT LCD
Speaker
DC 9V IN
You cannot playback discs
DC 9V IN
Power Switch
Video Out
Disc Lid
Audio Out
Headphone Jack
Volume Control
Remote Sensor
Power ON Indicator
Speaker
Power Switch
Press to turn on the unit.
Two speakers produce stereo sound.
DC 9V IN
Remote Sensor
For your reference:
Receiving remote control signal for
1. Place a disc with the label facing up, and push gently on the center of the disc so it goes into position.
Connect to the supplied AC Adapter/DC Car
Cord for power supply.
operation.
2. To start playing, press the PLAY/PAUSE button. (Some discs will start playing automatically).
3. To stop playing, press the STOP button.
TFT LCD
Power ON Indicator
4. To Skip Forward/Skip Backward, press the NEXT/PREV button.
It is green under normal playback.
Present high-resolution pictures.
5. To Fast Forward/Fast Backward, press/hold the NEXT/PREV button for about two seconds and
It is red under STANDBY mode.
press NEXT/PREV button repeatedly to increase the search speed.
Video Out -- Connect to external TV screen by the supplied RCA cables.
Audio Out -- Connect to external speaker system by the supplied RCA cables
Headphone Jack -- Connect to the supplied headphone.
As the headphone is plugged in, the speakers' output will be OFF.
Volume Control -- Adjust to the desired volume level.
.3.
Function Buttons
Function Buttons
LCD Mode
Press it once, the screen displays:
Basic Playback
LCD
Mode
1. Switch on the player
SCREEN
Open the DVD cover by hand.
Brightness
Slide the POWER switch to "ON" position.
Contrast
(If close the cover during playback, the LCD display will be OFF for
Color
power saving).
RESET
2. Load a disc
Display
Press the OPEN
button to open the disc lid and insert a disc with the label up.
Press the Display button to show the time and status information.
Close the disc lid by hand.
Press Display button the third time to quit the display mode.
If the single sided disc is placed in upside down, " NO DISC " or " BAD DISC " will appear
Play/Pause
on the on TV screen.
Press the Play button for the first time to play the disc.
After playing back all of the chapters in the title, the DVD player stops automatically and shows
Press the button for the second time to pause playing. (Still picture).
the menu screen.
Press again to resume playback.
Stop
3. Start playback
Press the Stop button once, to stop playback. Press the Play button to resume. Disc will begin
Press the PLAY button to start playing. (Some discs may play automatically).
playing from where it was stopped.
If a DVD disc menu appears on screen
Press the Stop button twice, to stop playback. Press the Play button to resume. Disc will begin
playing from the beginning.
Press the DIRECTION buttons to select the desired feature in the menu.
Skip Forward/Backward
Press ENTER button to confirm a selection in the menu.
Press the button to skip advance DVD chapter or CD track
4. Adjust the volume
Turn the volume control on main unit to the desired volume level.
Press the button to skip backward DVD chapter or CD track.
Problem disc messages
NOTE: Player will not skip forward or backward during "WARNING" section of a DVD disc.
The following message will be displayed on screen when there is a format problem with loaded disc:
Single chapter DVD or single track CD cannot be skipped.
"WRONG REGIONAL DISC"
Fast Forward/Backward
Region code of the disc is not matching to the player's (region 1 to region 6)
Press the button to fast forward through the disc. Repeatedly pressing the button will increase
"WRONG PASSWORD"
the search speed.
The rating level of the disc is higher than the rating level setting of the player.
The player will not play the disc.
Press the button to fast backward through the disc. Repeatedly pressing the button will
increase the search speed.
"WRONG DISC"
The player is equipped with automatic disc quality detection software. When the player detects a
Play
problem or damaged disc, the unit may play the disc at a lower quality or stop completely, depending
on the damaged level of the disc.
Press PLAY to resume normal playback.
Production qualities of DVD discs vary. Some discs may deviate from the industry standard. Some incorrectly
NOTE: The player is muted during fast forward or fast backward.
formatted discs may be played. However, the playback and operational quality may be substandard.
The player will not fast forward or fast backward during WARNING section of a DVD disc.
POWER management
If the player will not be in use for a long period of time, unplug the player for safety.
.9.
Setup Menu
Setup Menu
16:9 (Wide Screen): This is selected when the unit is connected to a wide-screen TV.
Various features of the DVD player can be adjusted in the Setup Menu.
The default setting is 4:3 LB
1. Press SETUP button.
Then the SETUP menu appears on screen.
Language Setup
NOTE: Certain DVD discs are formatted in wide screen (16:9) or letter box (4:3) only. Adjusting the
setting of the disc player will not change the screen size for these "Format-only" discs.
2. Press the UP/DOWN button to highlight the desired
OSD
item.
Menu
Audio
3. Press ENTER to confirm.
Subtitle
2. Screen Saver
4. Press the LEFT button to return to upper menu level.
Press the UP/DOWN button to shift between Screen Saver ON and OFF. And press ENTER to
5. To exit from the setup menu, press SETUP once more.
confirm.
Or press UP/DOWN to select the EXIT menu.
The default setting is On.
: Move
: Select SETUP : Quit
Title Chapter
The screen saver is useful to prevent your display from becoming damaged.
NOTE:
If the Screen Saver is set ON, the screen saver picture appears when you leave the DVD player in
Make sure your player is in STOP mode before setting the SETUP menu, otherwise some setup
stop mode for about a few minutes. Press any button on main unit or remote control to exit from the
features will be unavailable.
screen saver.
--Language Setup--
Automatic power off function
Press the UP/DOWN button to highlight the desired item from OSD/Menu/Audio/Subtitle, and press
After the screen saver has been engaged for about a few minutes, the DVD player will automatically
ENTER to confirm.
turn itself off, except during CD playback.
Item
Instruction
Default setting
3. TV System
To select the language of the OSD by the UP/DOWN button,
Press the UP/DOWN button to select the TV System from NTSC/PAL/AUTO, and press ENTER to
OSD
English
and press ENTER to confirm.
confirm. The default setting is NTSC.
(The TV System for north America is NTSC. Auto should only be used if you have a Multi-System
Menu
To select the language of the Menu by the UP/DOWN
English
TV.)
button, and press ENTER to confirm.
Audio
To select the language of the audio sound track by the
4. Brightness
English
UP/DOWN button, and press ENTER to confirm.
Press the UP/DOWN button to select your satisfied brightness effect from Normal/Bright/Soft. And
Select the language of the subtitle by the UP/DOWN button
press ENTER to confirm.
Subtitle
English
and press ENTER to confirm.
The default setting is Normal.
When OFF is selected, the subtitle will not be displayed.
5. Contrast
--Screen Setup--
Press the UP/DOWN button to select your satisfied contrast ratio from -4, -3, -2, -1, 0, 1, 2, 3 and
Press the UP/DOWN button to highlight the desired item from TV Type/Screen Saver/TV System/
4. And press ENTER to confirm.
Brightness/ Contrast, and press ENTER to confirm.
The default setting is 0.
Screen Setup
TV Type
Screen Saver
TV System
Brightness
Contrast
: Move
: Select SETUP : Quit
1. TV Type
Press the UP/DOWN button to select the aspect ratio from 4:3 PS (Pan Scan); 4:3 LB (Letter Box);
16:9 (Wide Screen). And press ENTER to confirm.
4:3 LB (Letter Box): This is selected when the unit is connected to a normal TV. Wide-screen
images are shown on screen, with black belt on the top and bottom.
4:3 PS (Pan Scan): This is selected when the unit is connected to a normal TV. Wide-screen images
are shown on screen, with some parts cut automatically.
.15.
Page
Views of the Remote Control
Remote Control
Title
Display
LCD
Power
Mode
LCD Mode
Setup
Menu
Play/Pause
Enter
Direction buttons
Stop
Mute
Zoom
Mute
PREV/NEXT Skip
Numeric buttons
FF/FB
Step
Clear
Step
LCD Mode
LCD MODE
Clear
Slow
Setup
Repeat A-B
PBC
SETUP
Stop
Repeat
Program
STOP
Play/Pause/Enter
Audio
PLAY/PAUSE
SubTitle
Angle
Up
NEXT/F.F/RIGHT
The buttons of same descriptions on the main unit/remote control are of same functions.
Down
NOTE
PREV/F.B/LEFT
Open
Battery Installation
NOTE
Refer to the diagram. Open the battery compartment of the
remote control. Insert batteries, and then close the compart-
ment.
To use the remote control, point it at the remote sensor of
the unit and operate in the range of 5 meters and at angle
of 60 degrees.
Generally, the batteries last for about one year. Replace the
batteries if the remote control does not work.
Do not spill water on the remote control.
Do not use remote control for other equipments at the same
time.
Remove the batteries if the remote control will not be in use
for a long period of time.
WARNING:
The battery used in this device may present a fire or chemical burn hazard if mistreated.
Do not recharge, disassemble, incinerate, or heat the batteries about 1000C (2120F).
Use of another battery may present a risk of fire or explosion. Dispose of used batteries.
Do not dispose of fire.
Keep batteries out of children's reach.
.4.
.5.
Function Buttons
Slow
Press SLOW button to play at slow motion. Repeatedly pressing the button will decrease the
slow
Press up/down direction button to select the
slow speed.
16:9
4:3
desired item, press left/right direction button to
Play
X1/2
X1/4
X1/8
X1/16
X1/32
make adjustment.
When SCREEN is selected, press left/right button
NOTE: The player is muted at SLOW mode.
to change screen dimension as 16:9 or 4:3.
When RESET is selected, press Enter button to
Disc MENU/TITLE
confirm, the above three control bar
will be reverted to the default.
While playing a DVD, press the MENU button to return to the DVD disc start menu.
While playing a DVD, press the TITLE button to return to the title menu.
NOTE: Some DVD discs do not allow the TITLE function.
Select an item in the menu
In the DVD disc start menu or in the Set Up menu
Press the DIRECTION buttons to highlight function icons.
Press the ENTER button to confirm a selection.
Numeric Key Pad
(Random Program access)
1). To directly access a DVD Chapter or a CD track, input the desired DVD Chapter or
CD Track number using the numeric key pad.Then press the ENTER button to
confirm.
2.) Input data for the DVD disc start menu or the player's setup menu.
NOTE: Some DVD discs do not allow direct access function.
MUTE
Mute
Press the MUTE button to select mute on or mute off.
ZOOM
PLAYING DVD
Zoom
Press the ZOOM button repeatedly and the TV screen will display
ZOOMx2
ZOOMx4
ZOOMx1
X2
X4
X8
X16
X32
Press the Direction buttons to move the picture position.
PLAYING JPEG
Press the ZOOM button repeatedly and the TV screen will display:
25%
50%
100%
150%
200%
While at 100%, press the direction button to rotate the picture.
While at 150% or 200%, press the direction button to move the picture position.
NOTE: The picture quality decreases as the picture size increases.
.10.
.11.
Setup Menu
--Custom Setup--
Press the UP/DOWN button to highlight the desired Custom item (Parental Ctrl, Password, Angle
Mark, Default), and press ENTER to confirm.
Custom Setup
Parental Ctrl
Password
Angle Mark
Default
: Move
: Select SETUP : Quit
A). Parental Ctrl
There are eight levels of Parental Control. Level one opens discs to people of all ages. Level
eight is suitable only for adults.
To change the parental control setting, a 4-digit code is required to be input first. (The default
code is 8888.) When the input code is confirmed, the level setting menu will appear. Select
the appropriate level by the UP/DOWN button, and press ENTER to confirm.
B). Password
Move the cursor to the PASSWORD prompt and press ENTER. Input the password 8888 if it is
the first use. After confirmation, you will be required to input a new 4-digit code, and verify again.
WARNING:
Please keep a copy of the new password in a safe place. Otherwise, you will not be able to
change the Parental Control.
Please remember your password, as the DEFAULT setting will revert everything BUT the
PASSWORD and Parental Control to the factory defaults.
C). Angle Mark
Choose between ON and OFF.
The default setting is ON.
When the Angle Mark function is ON, an icon will be displayed on screen if the disc has multiple
angle shots available for viewing.
Press ANGLE on the remote control to enjoy these scenes.
D). Default
This function allows you to change the player back to the factory default settings. All settings will
be changed back to the original settings except the Password and Parental Control.
.16.
.17.
Connections
Connecting to a TV set
(TV or monitor with audio/video input)
To AUDIO/VIDEO
To VIDEO OUT
input
To AUDIO OUT
Audio/Video cable(Supplied)
1. Refer to the owner's manual of your TV as well.
2. Before connecting the DVD player to a TV set, be sure to turn the power off
and unplug both units from the wall outlet.
.6.
Function Buttons
Repeat Section A-B
To repeat playback a specific section of a disc.
Press the A-B button at the starting point of the desired section, "Repeat A" appears on
screen.
Press the A-B button again at the end of the desired section, "Repeat A-B" appears on screen.
A-B
The player will start repeating playback the selected section from A to B until the function is
cancelled.
To cancel the function, press the A-B button once more to return to normal playback. "
Off"
will appear on screen for few seconds.
NOTE: Some DVD discs do not allow the A-B function playback. This function does not apply to MP3
discs.
REPEAT
This function allows repeated playback of a Title, Chapter, Track or Disc.
Press REPEAT button repeatedly to select the repeat mode.
Repeat
Playing DVD
Chapter
Title
Disc
Off
Playing CD
Track
Disc
Off
Playing MP3
Track
Folder
Disc
Off
NOTE: Some DVD discs do not allow the REPEAT function.
STEP
Step
Press STEP during playback, one frame of the image is played each time you press the button.
Press the Play button to quit the STEP mode.
AUDIO
For DVD playback:
Audio
While playing a DVD disc that contains multiple languages, press the AUDIO button repeatedly
to select the desired language of the audio sound track.
A DVD disc may contain up to 8 selectable audio languages.
The default AUDIO setting is English.
For CD/MP3 playback:
Press the AUDIO button repeatedly to shift among R/R, L/R, and L/L.
The default AUDIO setting is L/R.
NOTE:
If the desired language is not selected even after pressing the button several times, it means
that the language is not available on the disc.
When the power is turned on or the disc is removed, the language heard is the one selected
at the initial settings.
.12.
Specification
Trouble Shooting
Should your DVD player develop a problem, please check below before requesting service:
Power supply
DC 9.0V 2A (AC adapter TERMINAL)
Symptom
Check and Action
Power consumption
<=9w
1. Make sure the unit has been powered on manually.
Signal system
NTSC
2. Check if the power cord has been properly connected to the power outlet.
No power
3. Make sure the battery pack is fully charged.
Video output
1+0.2V (p-p), 75ohm, Negative sync., 3.5 mm mini jack x1
Audio output
1.5 Vrms (1 KHz, 0dB), 3.5 mm mini jack x1
Does not play
1. No disc, load a disc.
2. Disc has been loaded upside down. Place the disc with the label side up.
Earphone terminal
3.5mm stereo mini jack x1
3. Disc's rating level is higher than the player's setting.
Signal /Noise ratio(audio)
90dB typical
4. Disc is incorrect type for the player.
5. Disc is damaged or dirty. Clean the disc or try another one.
Dynamic range(audio)
90dB typical
6. Moisture may be condensed inside the player. Remove the disc and leave the unit
Panel size
7 inch (16:9)
power on for one or two hours.
Resolution
480(H) x 234 (V) (QVGA) Pixels
No Picture
1. Check if the TV set has been powered on. Use TV remote to select AV signal for
Laser
Wavelength 650 nm
DVD rather than broadcast.
Operating conditions
Temperature: 0 c to 35 c. Operation status : Horizontal
2. Check if the system connection is proper and secure.
Dimensions
187x170x50mm (Main Unit & Batt.)
3. Check if the connection cables are damaged.
4. Clean the disc.
Weight
937g (Main Unit & Batt. )
Picture noisy/
1. Disc is damaged or dirty. Clean the disc or try another one.
distorted
2. Reset the color system of the TV set.
3. Make sure the DVD player is not connected through a VCR, cable or satellite dish.
No sound or sound
1. Check if the TV and amplifier have been switched on and correctly set.
output not complete
2. Check if the TV and amplifier system connections are secured.
3. Press AUDIO button to select other audio tracks of the disc.
4. Check if the MUTE function of the TV or amplifier has been activated.
5. There will be no sound output during REVERSE PLAY/PAUSE/SLOW and
SEARCH.
Remote control
1. Make sure the POWER button on the unit has been turned on manually.
does not work
2. Remove the obstacles between the remote control and the player.
3. Point the remote control towards the remote sensor on the player.
4. Check if the batteries of the remote control have been loaded with correct
polarities.
5. Replace the batteries of the remote control.
Malfunction
Should the player develop a malfunction, unplug the player for 30 minutes. After
that, power on the player and the restore function should reset the player.
.18.
.19.
Advertisement
