Related Manuals for MD SPORTS DH44109
Summary of Contents for MD SPORTS DH44109
- Page 1 Please contact us before returning the product to the store. Toll Free: 877-472-4296 MODEL : DH44109...
- Page 2 LIMITED 90 DAYS WARRANTY This product is covered by a limited warranty that is effective for 90 days from the date of purchase. The warranty covers any defects in parts and workmanship. This Limited Warranty gives you specific legal rights and you may also have other rights which very from one state (province) to another.
-
Page 3: Tools Required
IMPORTANT NOTICE! Please contact us before returning the product to the store. Please Keep Your Instructions! Your Model number is necessary should you need to contact us. Please read through this instruction manual book to familiarize yourself with all parts and assembly steps. - Page 4 DH 44109 PARTS LIST CURVED OUTER LEG 6MM WASHER RIGHT TABLE SURFACE LEFT TABLE SURFACE M6 X 47MM BOLT WITH CAPS 24 PIECES 2 PIECES 2 PIECES 8 PIECES 2 PIECES CURVED INNER LEG LINKAGE TUBE WITH WITH CAPS STOP BRACKET LINKAGE TUBE BRACKET LOCK PIN...
- Page 5 TABLE TENNIS PADDLE CONTROL BOX 2 PIECES 1 PIECE ASSEMBLY INSTRUCTIONS 1. Find a clean, level place to begin the assembly of your Table Tennis Table. The table will be assembled upside down and then turned over. This is a heavy game and tuning it over will require at least two strong adults. 2.
- Page 6 FIG.2 7. Place one Curved Outer Leg (# 5) on the player end of the table half and one Curved Inner Leg (#6) on the center end of the table half, and then using the Leg Bracket (#19) attach legs to the table with twenty-four Screw (#18). NOTE: Make sure that the oval cut-out in the Leg Bracket are facing the center of the table for proper installation.
- Page 7 FIG.3 9. Attach one end of the Linkage Tube (#8) to the inside of the Curved Outer Leg (#5) using one Bolt (#3), two Washers (#4), one Spacer (#14) and one Nut (#13). 10. Repeat the same for the other end of this Linkage Tube, only attaching it to the outside of the Curved Inner Leg (#6). 11.
- Page 8 FIG.4 15. Place the Molded Protective Corners (#17) flush with table corner using twelve Screws (#18). See FIG.4A 16. Place the End Apron (#22) between the Corners(#17) using four Screws (#18) per End Apron. See FIG.4 17. Place the Side Apron (#23) and Storage Bag (#30) flush with table edge at the side of the table using four Screws (#18) per Side Apron.
- Page 9 FIG.5 18. Place the Wheel(#25) into the Curved Inner Legs. 19. With the logo upside-down, attach the Plastic Leg Panel (#21) to the Curved Inner Leg (#6) using two Bolts (#11) and two Washers (#4). NOTE: Do not tighten securely at this time. 20.
- Page 10 FIG.6 22. Before turning the table over, make sure to push the Curved Inner Leg (#6) towards the center of the table in order to engage the stop. NOTE: Two adults are required to turn this table over 23. One person should stand at each center of the table and turn the table over completely so that it rests on its legs. 24.
- Page 11 FIG.7 Attach the Net Post A & B (#16 & #31) at the middle of the table and slide the net over the post. Stretch the Net (#15) across the center of the table and slip the net over the post on the opposite side. See FIG. 7. Place the Control Box (#37) at a player’s left corner and install it between the Apron Corner and Short Side Apron (#34) using two Screws (#18).
- Page 12 FIG.8 31. Engage the Caster (wheels ) Lock. 32. Folding the table - First fold the side of the table without the net clip. Hold the end securely and lift the table. Make sure the Lock Pin (#10) is locked. Attach the Safety Strap (#24) to prevent the sides from falling. Repeat for the other side.
- Page 13 Batteries Replacement Instructions Note: AAA Batteries are not included. Step 1: Use a screwdriver to loosen the screw. Step 2: Use the provided key to pull the battery box out. Use the key in this position to pull the box out.
- Page 14 Step 3： Note: Make sure to put all the batteries in the right way inside the box. Positive pole（+） Negative pole（-） Step 4: After having placed the batteries, push the box back inside the device. Push the box inside Step 5: Use the screw to tighten the cover of the box.
- Page 15 SCORER OPERATION Electronic Scorer Control Box 1. Remove the battery cover and insert four AAA batteries into the battery box. AAA Batteries not included. 2. Turn on the scorer by pressing the “ON/OFF” button, therewith starting the game. Both screens will show a player, the HOME Serve “...