Microsoft Xbox 360 Setup Manual page 5

To avoid damaging the power cords and power supply:
• Do not wrap power cords around the
power supply.
• Protect the power cords from being
walked on.
• Protect cords from being pinched or
sharply bent, particularly where they
connect to the power outlet, the power
supply unit, and the console.
• Do not jerk, knot, sharply bend, or
otherwise abuse the power cords.
• Do not expose the power cords to
sources of heat.
• Keep children and pets away from the
power cords. Do not allow them to bite or
chew on them.
• When disconnecting the power cords,
pull on the plug—do not pull on the cord.
• Do not let the power supply hang from
either power cord.
THE XBOX 360 CONTROLLER
The Xbox 360 Controller is for use with the
Xbox 360 video game and entertainment
system or with most Microsoft Windows XP-
based computers.
Prior to using the Xbox 360 Controller with a
Windows XP-based PC, you must install Xbox
360 Controller for Windows software
available at www.windowsgaming.com. This
software includes important safety
information and health warnings.
The Xbox Guide Button
All controllers and remotes for your Xbox 360
video game and entertainment system are
equipped with an Xbox Guide button. Press
the Xbox Guide button to show the Xbox Guide
at any time.
6
If a power cord or power supply becomes
damaged in any way, stop using it
immediately and contact Xbox Customer
Support for a replacement.
Unplug your Xbox 360 video game and
entertainment system during lightning
storms or when unused for long periods
of time.
Always connect the power cords according
to the following instructions:
Fully insert the power supply cord into
1
the Xbox 360 console until it clicks.
2 Plug the AC power cord into the power
supply until it stops.
Plug the other end of the AC power cord
3
into the wall outlet.
Ring of Light
The controller Xbox Guide button and the
console Power button are both surrounded by
the Ring of Light, which is made up of four
quadrants. When a controller is connected to
your console, it is assigned a quadrant, which
glows green to indicate the controller's
position. As more controllers are added, each
quadrant of the console glows green to reflect
the added controller's number. The Ring of
Light on the console will also flash
combinations of red if there are system
problems. See "Troubleshooting" for more
details.
The Inline Release
Your controller cord has an inline release.
This is a safety feature designed to reduce
the chance of the Xbox 360 console or
computer falling when the cord is pulled. If
the console or computer falls and hits
someone, especially a small child, it could
cause serious injury. To reduce the risk of
injuries or damage to the console or
computer, it is important to use the
controller and the inline release properly.
Use the controller connector, not the inline
release, to routinely connect and
disconnect the controller. If an inline
release disconnects, simply reconnect it by
aligning the grooved indentations and
pressing the two parts completely
together. The controller will not work
unless the inline release is connected
properly.
WARNING
Never tape, glue, or otherwise prevent an
inline release from pulling apart.
The inline release reduces, but does not
eliminate, the risk of the computer or
console being pulled off its surface. To
further reduce the risk:
• Do not allow anyone to pull on the
controller or controller cord in a way
that causes the computer or console
to move.
• Do not allow controller cords to become
crossed or tangled with one another.
Connect Your Controller to Your
Xbox 360 Console
To connect the Xbox 360 Controller to the
Xbox 360 console, insert the controller cord
connector into any USB port on the console.
To disconnect, pull the controller cord
connector out. Be sure to pull on the
connector, not the cable.
NOTE
Do not touch controller cord terminals with
your fingers or allow metal parts to touch
them. Doing so may damage the controller or
the console.
Never force a connector into a USB port. If the
connecter doesn't easily connect, flip the
connector over and try again.
Turn on Your Xbox 360 Console
To turn on your Xbox 360 console, press the
Xbox Guide button or Start on your controller,
or press the Power or Eject button on the
console.
To turn off your console, press the Xbox Guide
button to display the Xbox Guide, select
Options, and then Shut Down. You can also
press the Power button on your console to
turn it off.
Select Language and Other Settings
The first time you turn on your Xbox 360
console, you will be prompted to enter a
Language. Follow the prompts to select a
language for your Xbox 360 video game and
entertainment system.
You can change language and other console
settings of the System area of the Xbox
Dashboard. You can select other settings from
the System area also, including time, audio,
display, and whether you want the Xbox 360
console to turn off automatically after six
hours of non-use.
7