Table of Contents
Advertisement
Cautions and Warnings
Please review the following cautions and warnings.
Environmental and mounting specifications
Operating temperature: 0 - 40°C (32 - 104°F)
Storage temperature: -35 - 70°C (-31 - 158°F)
Humidity: 20 to 90% non-condensing
Operating Altitude: <2250m (7400ft)
Elevated Operating Ambient: If installed in a closed or multi-unit rack assembly, the operating
ambient temperature of the rack environment may be greater than room ambient. Therefore,
consideration should be given to installing the equipment in an environment compatible with
the maximum ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Installation of the equipment in a rack should be such that the amount of
air flow required for safe operation of the equipment is not compromised.
Mechanical Loading: Mounting of the equipment in the rack should be such that a hazardous
condition is not achieved due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the equipment to
the supply circuit and the effect that overloading of the circuits might have on overcurrent
protection and supply wiring. Appropriate consideration of equipment nameplate ratings
should be used when addressing this concern.
Reliable Earthing: Reliable earthing of rack-mounted equipment should be maintained.
Particular attention should be given to supply connections other than direct connections to the
branch circuit (e.g. use of power strips).
Federal Communication Commission (FCC) – USA
This device complies with Part 15 of FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received; including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy, and
if it is not installed and used in accordance with the instruction manual, it may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case the user will be required to correct the interference
at his own expense.
WARNING: Any changes or modifications to this product not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
Industry Canada Equipment Standard for Digital Equipment (ICES) –
Canada
CAN ICES-3 (A) / NMB-3 (A)
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regula¬tions of the Canadian Department of
Communications.
Page 10
Le présent appareil numérique n'emet pas de bruits radioélectriques dép¬assant les limites
applicables aux appareils numeriques de la classe A préscrites dans le Règlement sur le
brouillage radioélectrique édicte par le ministère des Communications du Canada.
Voluntary Control Council for Interference (VCCI) – Japan
この装置は、クラスＡ情報技術装置です。 この装置を 家庭環境で使用すると電波妨害を
引き起こすことがあります。 この場合には使用者が適切な対策を講ずるよう要求される
ことがあります。ＶＣＣＩ－Ａ
Bureau of Standards Metrology and Inspection (BSMI) – Taiwan
這是甲類的資訊產品，在居住的環境中使用時，可能會造成射頻干擾，在這種情況下，使用
者會被要求採取某些適當的對策。
The presence conditions of the restricted substance (BSMI RoHS table) are available at the
link below:
https://www.fortinet.com/bsmi
China
此为A级产品，在生活环境中，该产品可能会造成无线电干扰。这种情况下，可能需要用户
对其采取切实可行的措施。
European Conformity (CE) - EU
This is a Class A product. In a domestic environment, this product may cause radio interference,
in which case the user may be required to take adequate measures.
Korean Certification (KC) – Korea
주의
A급 기기 이 기기는 업무용으로 전자파 적합 등록을 한 기기이오니
판매자 또는 사용자는 이 점을 주의하시기 바라며 만약
잘못 판매 또는 구입하였을 때에는 가정용으료 교환하시기 바랍니다.
Grounding
Ensure your Fortinet product is connected and properly grounded to a lightning and surge
protector. WAN or LAN connections that enter the premises from outside the building should
be connected to an Ethernet CAT5 (10/100 Mb/s) surge protector.
Shielded Twisted Pair (STP) Ethernet cables should be used whenever possible rather than
Unshielded Twisted Pair (UTP).
Do not connect or disconnect cables during lightning activity to avoid damage to your
Fortinet product or personal injury.
Electrostatic discharge (ESD) can damage Fortinet equipment. Only perform the procedures
described in this document from an ESD workstation. If no such station is available, you can
provide some ESD protection by wearing an anti-static wrist strap and attaching it to an
available ESD connector or other bare metal object.
Note: For DC installations, a readily accessible disconnect device shall be incorporated in the
building installation wiring.
Caution: For devices that contain a battery there is a risk of explosion if battery is replaced by
an incorrect type. Recycle used batteries according to your local regulations.
警告
本電池如果更換不正確會有爆炸的危險
請依製造商說明書處理用過之電池
Page 11
Advertisement
Table of Contents
