Advertisement
Quick Links
Advertisement
Related Manuals for Stanley XGRIP N09QI
Summary of Contents for Stanley XGRIP N09QI
- Page 1 Service Aid XGRIP N09QI Hydro-Pneumatic Tool - 1 -...
- Page 2 STANLEY Engineered Fastening will not accept any liability for damage resulting from activities carried out by third parties. The working names, trade names, registered trademarks, etc. used by STANLEY Engineered Fastening should not be considered as being free, pursuant to the legislation with respect to the protection of trademarks.
-
Page 3: Table Of Contents
Contents Abbreviations: ............................4 General instructions: ..........................4 Service kit: ..............................4 Proper function of riveting tool: ......................5 Assembly drawing of riveting tool: ....................... 6 Informative list of spare parts of riveting tool: ................... 7 Instructions for assembling and disassembling – steps 1-11: ............. 9 - 3 -... -
Page 4: Abbreviations
1. Abbreviations: CA - Compressed air MP - Special tool (assembly jig) 2. General instructions: 1. Riveting tool is always deconnected from the compressed air, unless otherwise stated. 2. All threads are clockwise. 3. Riveting tool is gripped in a stand (see chapter 8) while assembling and disassembling, unless otherwise stated. -
Page 5: Proper Function Of Riveting Tool
4. Proper function of riveting tool: Tool function Operator activity Connect the riveting tool to CA, if the tool is equiped with main valve, turn it on. Pos. 70 CA does not leak, motor does not rotate is on the front extreme position, not pressed Put a rivet on pos. -
Page 6: Assembly Drawing Of Riveting Tool
5. Assembly drawing of riveting tool: - 6 -... -
Page 7: Informative List Of Spare Parts Of Riveting Tool
6. Informative list of spare parts of riveting tool: Position Part Number. Description O900A00275 Mandrel M3 O900A00276 Mandrel M4 O900A00277 Mandrel M5 O900A00278 Mandrel M6 O900A00279 Mandrel M8 O900A00280 Mandrel M10 O900A00281 Mandrel M12 O900A00282 Anvil M3 complete O900A00283 Anvil M4 complete O900A00284 Anvil M5 complete O900A00285... - Page 8 6703 O920N08074 O - ring 4/2,2 Sh 70 6704 O920063029 O - ring 4/2 Sh 70 O920063035 Dowel pin 3 x 20 DIN 7 O920R50S60 Excentric trigger O920R50S62 Trigger red O920R50S46 Compression spring N-8400000086500 Sticker of type (MS865) - 8 -...
-
Page 9: Instructions For Assembling And Disassembling - Steps 1-11
7. Instructions for assembling and disassembling – steps 1-11: Step 1 Disassembly: Loosen and screw out pos. 59 (2x) with using tommy bar 10, loosen and screw out pos. B60 with using screwdriver and put pos. 77 out. Put pos. B40 with pos. B67 out off pos. 57 (2x), put pos. B67 out off pos. B40. Assembly: Put pos. - Page 10 Step 2 Disassembly: Put pos. B26 with pos. 43 out of pos. B25 and pos. 57 (2x), put pos. 43 out of pos. B26. Then pour out the hydraulic oil from the riveting tool to the suitable container. Assembly: Pour hydraulic oil into pos. B9 (we recommended hydraulic oil HYSPIN AWHM 32 CASTROL or hydraulic oils grade HLP ISO VG 32), oil level up to 2.
- Page 11 Step 3 Disassembly: Loosen and screw out pos. 57 (2x) with using nut and contranut on thread M6. Remove nut and contranut and screw pos. 57 (2x) to pos. B25 (thread M6). Pull both pos. 57 and pos. B25, put pos. 24 out.
- Page 12 Step 4 Disassembly: Screw pos. 2 and pos. 1 out. Screw pos. 5 out of pos. B9 with using wrench 24 and put pos. 6 out with using MP32. Assembly: Put pos. 6 on pos. 5, screw pos. 5 to pos. B9 and tighten with using wrench 24. Screw pos. 1 on pos.
- Page 13 Step 5 Disassembly: Screw pos. B18 out of pos. B9 with using hook spanner 30-32 (MP28). Be carefull, pos. B18 is under spring pressure pos. 19 and pos. 20. Gradually slide pos. 19, pos.20, pos. 21, pos. 22, pos. 23 out and put pos.
- Page 14 Step 6 Disassembly: Put out pos. B16. Assembly: Put on pos. B16 and move around a slight amount so that hexagon pos. B16 and pos. 8 match, then move pos. B16 to the stop. Turn pos. 3 to check if the installation was successful, rotation in pos.
- Page 15 Step 7 Disassembly: Put wrenches 12 (2x) on pos. 3 and pos. 4, loosen and screw out pos. 3, put hex key on pos. 8 from the inside and screw out pos. 4. Assembly: Screw pos. 4 on pos. 8 (recess in direction to pos. B14) so that the lenght between pos. 4 and pos. B14 is 1 mm (see the detail).
- Page 16 Step 8 Disassembly: Put pos. 8. out of pos. B14. Assembly: Put pos. 8 into pos. B14. - 16 -...
- Page 17 Step 9 Disassembly: Put pos. 7 out of pos. B14 with using MP32. Put pos. B14 out of pos. B9. ! Be careful and do not damage the sealing in pos. B9! Assembly: Screw MP52 into pos. B9. Lubricate external surface of pos. B14, inner surface of pos. B9 and related sealing of pos.
- Page 18 Step 10 Disassembly: Place a pin cca 2,8 mm in diametre to the pos. 68 and knock out with a hammer from pos. B9, put out pos. 70 and pos. 69. Assembly: Put pos. 69 to pos. 70 and this complete put into pos. B9, put on pos. 68 and beat in with hammer and a pin cca 2,8 mm in diametre so that the pos.
- Page 19 Step 11 Oil filling after assembling the tool: Connect the tool to the source of CA! Press and release the trigger several times. Disconnect the tool from the source of CA! Unscrew pos. 11 with socket-screw key no.3. Fill hydraulic oil (from the supplied bottle with hydraulic oil) into MP53, take extra care to avoid air sucking, air must not be present in the hydraulic oil.
- Page 20 Avdel , POP are registered trademarks of Stanley Black & Decker, Inc. and its affiliates. The names and logos of other companies mentioned herein may be trademarks of their respective owners. Data shown is subject to change without prior notice as a result of continuous product development and improvement policy. Your local STANLEY Engineered Fastening representative is at your disposal should you need to confirm latest information.