Omron NE1A Series Manual page 245

Monitoring Test Output Terminals: NE1A-SCPU01-V1
Explicit Service
message
Monitor Mode for Read
Terminal Mainte-
nance Information
Write
SV for Test Output Read
Total ON Time or
Contact Operation
Counter
Write
Read Test Output Read
Total ON Time or
Contact Operation
Counter
Reset Test Output Reset
Total ON Time or
Contact Operation
Counter
Read Monitor Read
Status of Test
Output Total ON
Time or Contact
Operation Counter
Read Test Output Read
Safety Flag
Read Test Output Read
Error Information
Cause
Read OR of Test Read
Output Safety Flags
Read OR of Read
Monitor Status of
Test Output Total
ON Times or
Contact Operation
Counters
246
Function
Service
Reads the monitor mode of 0E hex
maintenance information of the
test output (1 to 4) specified by
the Instance ID.
Writes the monitor mode of 10 hex
maintenance information of the
test output (1 to 4) specified by
the Instance ID.
Reads the SV of the total ON 0E hex
time (unit: seconds) or contact
operation counter (unit: opera-
tions) for the input (1 to 4) spec-
ified by the Instance ID.
Writes the SV of the total ON 10 hex
time (unit: seconds) or contact
operation counter (unit: opera-
tions) for the input (1 to 4)
specified by the Instance ID.
Reads the total ON time (unit: 0E hex
seconds) or contact operation
counter (unit: operations) for
the input (1 to 16) specified by
the Instance ID.
Resets to 0 the total ON time 05 hex
(unit: seconds) or contact
operation counter (unit: opera-
tions) for the test output (1 to 4)
specified by the Instance ID.
Reads the monitor status of the 0E hex
total ON time or contact opera-
tion counter of the test output (1
to 4) specified by the Instance
ID.
Reads the normal flag status 0E hex
for the test output (1 to 4)
specified by the Instance ID.
Reads the cause for the normal 0E hex
flag of the test output (1 to 4)
specified by the Instance ID
being OFF (error).
Reads the logical OR of the 0E hex
normal flag status for all test
outputs 1 to 4.
Reads the logical OR of the 0E hex
monitor status of the total ON
time or contact operation
counter for all test outputs 1 to
4.
Command
Class In- At-
code stance tribute
ID
ID ID
307 01 to 04 83 hex
hex hex
307 01 to 04 83 hex
hex hex
307 01 to 04 86 hex
hex hex
307 01 to 04 86 hex
hex hex
307 01 to 04 84 hex
hex hex
307 01 to 04 84 hex
hex hex
307 01 to 04 85 hex
hex hex
307 01 to 04 68 hex
hex hex
307 01 to 04 76 hex
hex hex
308 01 hex 69 hex
hex
308 01 hex 72 hex
hex
Appendix A
Response
Data size
--- 1 byte
00 hex: Total ON time
mode
01 hex: Contact opera-
tion counter
mode
1 byte ---
00 hex: Total
ON time mode
01 hex: Contact
operation
counter mode
--- 4 bytes
0000 0000 to FFFF
FFFF hex
(0 to 4,294,967,295)
4 bytes ---
0000 0000 to
FFFF FFFF hex
(0 to
4,294,967,295)
--- 4 bytes
0000 0000 to FFFF
FFFF hex
(0 to 4,294,967,295)
--- ---
--- 1 byte
00 hex: In range
01 hex: Out of range
(over monitor
value)
--- 1 byte
00 hex: Normal
01 hex: Error
--- 1 byte
00 hex: No error
01 hex: Invalid
configuration
02 hex: Overcurrent
detection
05 hex: High constant
error
06 hex: Undercurrent
detection
--- 1 byte
00 hex: All normal
01 hex: Error
--- 1 byte
00 hex: All in range
01 hex: Test output out
of range (over
monitor value)