Related Manuals for Planet LRP-422CST
Summary of Contents for Planet LRP-422CST
- Page 1 Industrial 4-port Coax + 2-port 10/100/1000T + 2-port 100/1000X SFP Long Reach PoE over Coaxial Managed Switch LRP-422CST Quick Installation Guide...
-
Page 2: Table Of Contents
Table of Contents 1. Package Contents ..................3 2. Requirements ..................... 4 3. Wiring the Power Inputs ................5 4. Terminal Setup ................... 6 5. Logon to the Console .................. 7 6. Configuring IP Address via the Console ............8 7. Saving the Configuration via the Console .............10 8. Starting Web Management .................11 9. -
Page 3: Package Contents
1. Package Contents Thank you for purchasing PLANET Industrial 4-port Coax + 2-port 10/100/1000T + 2-port 100/1000X SFP Long Reach PoE over Coaxial Managed Switch. “LRP Managed Switch” is used as an alternative name in this Quick Installation Guide. Open the box of the LRP Managed Switch and carefully unpack it. The box should contain the following items: z The LRP Managed Switch x 1 z Quick Installation Guide x 1 z RS232 to RJ45 Console Cable x 1... -
Page 4: Requirements
2. Requirements Workstations running Windows XP/2003/Vista/7/8/2008, MAC OS X or later, Linux, UNIX, or other platforms are compatible with TCP/IP protocols. Workstations are installed with Ethernet NIC (Network Interface Card) Serial Port Connection (Terminal) The above Workstations come with COM Port (DB9) or USB-to-RS232 converter. The above Workstations have been installed with terminal emulator, such as Hyper Terminal included in Windows XP/2003. Serial cable -- one end is attached to the RS232 serial port, while the other end to the console port of the LRP Managed Switch. -
Page 5: Wiring The Power Inputs
6 contacts. Please follow the steps below to insert the power wire. 1. Insert positive/negative DC power wires into contacts 1 and 2 for Power 1 or 5, and 6 for Power 2. LRP-422CST: DC 48~56V Figure 3-1: LRP-422CST Upper Panel 2. Tighten the wire-clamp screws for preventing the wires from loosening. Power 1 Power 2 Positive (+) Pin... -
Page 6: Terminal Setup
4. Terminal Setup To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to the RJ45 type of the console port of the LRP Managed Switch. PC / Workstation with Terminal Emulation Software Managed Switch RS232 to RJ45 Cable Serial Port... -
Page 7: Logon To The Console
5. Logon to the Console Once the terminal is connected to the device, power on the LRP Managed Switch, and the terminal will display “running testing procedures”. Then, the following message asks to log-in user name and password. The factory default user name and password are shown as follows, and the login screen in Figure 5-1 appears. -
Page 8: Configuring Ip Address Via The Console
6. Configuring IP Address via the Console The LRP Managed Switch is shipped with default IP address as follows: IP Address: 192.168.0.100 Subnet Mask: 255.255.255.0 To check the current IP address or modify a new IP address for the Switch, please use the procedures as follows: Show the current IP address 1. At the “LRP-series#” prompt, enter “show ip”. 2. The screen displays the current IP address, Subnet Mask and Gateway as shown in Figure 6-1. Figure 6-1: IP Information Screen... - Page 9 Configuring IP address 3. At the “LRP-series#” prompt, enter “configure”. 4. At the “LRP-series (config)#” prompt, enter the following command and press <Enter> as shown in Figure 6-2. LRP-series (config)# ip address 192.168.1.100 mask 255.255.255.0 LRP-series (config)# ip default-gateway 192.168.1.254 The previous command would apply the following settings for the Switch. IP Address: 192.168.1.100 Subnet Mask: 255.255.255.0 Gateway: 192.168.1.254 Figure 6-2: IP Address Screen 5. Repeat Step 1 to check if the IP address is changed. If the IP is successfully configured, the LRP Managed Switch will apply the new IP address setting immediately. You can access the Web interface of the LRP Managed Switch through the new IP address.
-
Page 10: Saving The Configuration Via The Console
7. Saving the Configuration via the Console In the switch, the running configuration file stores in the RAM. In the current version, the running configuration sequence running-config can be saved from the RAM to FLASH by copying the running-config startup-config command, so that the running configuration sequence becomes the startup configuration file, which is called configuration save. -
Page 11: Starting Web Management
8. Starting Web Management The following shows how to start up the Web Management of the LRP Managed Switch. Note the LRP Managed Switch is configured through an Ethernet connection. Please make sure the manager PC must be set on the same IP subnet address. - Page 12 Logging in to the LRP Managed Switch 1. Use Internet Explorer 8.0 or above Web browser and enter IP address http://192.168.0.100 to access the Web interface. 2. When the following dialog box appears, please enter the default user name and password “admin”. The login screen in Figure 8-2 appears. Default Username: admin Default Password: admin Figure 8-2: Login Screen 3. After entering the password, the main screen appears as Figure 8-3 shows.
- Page 13 The Switch Menu on the left of the Web page lets you access all the commands and statistics the LRP Managed Switch provides. Figure 8-4: Switch Menu Now, you can use the Web management interface to continue the Switch management. Please refer to the user’s manual for more.
-
Page 14: Starting Long Reach Poe Communication
Note Connect the Coaxial Cable 1. Insert the coaxial cable with one side being the 75ΩBNC plug connector into the Long Reach Ethernet coaxial interface. 2. Connect the other end of the cable to a device with Long Reach Ethernet coaxial extender installed. 3. Tighten the BNC male connector gently. RJ45 5C2V/RG6 75Ω Coaxial Cable Long Reach Power over Ethernet PoE PT Camera LRP-101CE LRP-422CST... - Page 15 4. Enable Long Reach Power over Ethernet function for the all LRP ports from WebUI. 5. Check the LNK LED of the Long Reach Power over Ethernet interface on the front of the LRP Managed Switch. Ensure that the Long Reach Power over Ethernet interface is operating correctly.
- Page 16 Remove the connected Coaxial Cable 1. Make sure there is no network activity anymore. 2. Disable Long Reach Power over Ethernet function for all the LRP ports from WebUI. 3. Loosen the BNC male connector gently. 4. Pull out the coaxial cable gently. RJ45 5C2V/RG6 75Ω Coaxial Cable Long Reach Power over Ethernet PoE PT Camera LRP-101CE LRP-422CST...
- Page 17 Note Managed Switch. 1. The package contains warning stickers, which should be stuck on the coaxial cable connector before using PLANET LRP-422CST and LRP extender. If connected with a Non-PLANET LRP extender, it might cause damage to the equipment. 2. After the LRP PoE port is enabled, the center pin of the coaxial cable is with electricity. Do not touch center pin or connect this...
-
Page 18: Saving Configuration Via The Web
10. Saving Configuration via the Web In the LRP Managed Switch, the running configuration file stores in the RAM. In the current version, the running configuration sequence of running-config can be saved from the RAM to FLASH by “Save Configurations to FLASH” function, so that the running configuration sequence becomes the startup configuration file, which is called configuration save. -
Page 19: Recovering Back To Default Configuration
10 seconds. After the device is rebooted, you can log in the management Web interface within the same subnet of 192.168.0.xx. CAUTION The LRP interface is allowed to connect to LRP Extender only. LRP-422CST RESET Figure 11-1: LRP-422CST Reset Button... -
Page 20: Customer Support
PLANET online FAQ: http://www.planet.com.tw/en/support/faq.php?type=1 Switch support team mail address: support_switch@planet.com.tw LRP-422CST User’s Manual: http://www.planet.com.tw/en/support/download.php?type1=1&model=&type=3 (Please select your switch model name from the Product Model drop-down menu) Copyright © PLANET Technology Corp. 2015. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.