Crosley XTW4214 Owner's Manual & Installation Instructions page 6

Getting started
Step 1
• Add fabric softener to the
fabric softener dispenser;
see page 13 or 14
(depending on model).
• If using detergent packets,
add to the bottom of the
wash basket before adding
clothes. We recommend
the use of High Efficiency
laundry packs.
Power (on some models)
AA
Press to "wake up" the display. If the display is active, press to put the washer into idle mode.
NOTE: Pressing Power does not disconnect the appliance from the power supply.
Start/Pause
A
Press Start to begin the cycle. NOTE: If the lid is closed, the lid will lock only during the load sensing portion of the cycle (when
the Auto selection is made or models which do not have a load size selection) and during spin portions of the cycle. Lid will unlock
after load sensing and spin.
NOTE: Unless Bulky Items/Bulky cycle is selected, the lid must be closed for the washer to start cycle. On models with a
display, if the lid is open, "Lid" will scroll across the display. During the load sensing portion of the cycle, the lid will lock and
"SEnSing" will scroll across the display.
Pressing Pause will unlock the lid (if locked at that time), pause the cycle and the Start indicator light will blink.
To continue the cycle, press Start again. If water remains in the machine, select the Drain & Spin cycle to drain basket and
spin water out of the washer basket. NOTE: Machine will automatically cancel and drain when water is present and the lid is
left open for 15 minutes or the unit is left in a paused state for 24 hours with the lid closed. Select cycle and press Start to
begin new cycle.
Status Lights and Display (on some models)
B
Cycle status lights: Shows whether the washer is in the Delay (on some models), Fill, Soak, Wash, Rinse or Spin portion
of the cycle.
If an out-of-balance condition is detected by the washer, the Spin light will blink during the remaining portion of the cycle
and will stay illuminated for a short time after cycle completion. When this occurs, the washer is taking actions to correct the
out-of-balance condition and complete the cycle normally. In some cases, the washer may not be able to balance the load
and spin up to full speed. If you notice the load is more wet than normal at the end of the cycle, redistribute the load evenly
in the wash basket and run a Drain & Spin cycle.
Display (on some models): The display shows the approximate time remaining until the end of the cycle. NOTE: The cycle time
is affected by how long it takes the washer to fill. This depends on the water pressure in your home. The size of the load being
washed also significantly impacts cycle time, with larger loads taking longer.
In addition, this display will, "scroll" the washer status:
• bALAnCIN g Start of rebalancing cycle to redistribute clothes. Stops after rebalancing is complete.
• dELAY
• End
• FILL
• H2O SUPPLY Can not sense water level (valves possibly turned off).
• LId
• SEnSIng
• PAUSE
Feature status lights indicate (see sections E and H for more details):
Pause - Will display when washer is paused between cycles.
Controls - The washer is locked - will blink once if you press any button or turn the cycle knob.
Lid Lock - The lid is locked. See the Control Lock description.
Spin Stop - Indicates wash basket is coasting to a stop following spin. Lid will not unlock until basket has fully come to a stop.
6
Step 2
• Loosely add items around
agitator or Infusor. Overloading
may negatively impact wash
performance. See page 15 for
suggested loading examples.
• Add the manufacturer's
recommended amount of detergent
to the top of the load after adding
clothes. We recommend the use of
High Efficiency laundry detergent
packs.
When Delay Wash is initiated. Replaced with estimated time when cycle starts.
End of current cycle.
"FILL" will scroll across display for the first 45 seconds of fill, afterwards the estimated end of cycle time is
displayed.
Cycle stopped because lid is open. Close the lid.
Sensing load size and type before and during fill (normal).
Cycle paused because the Start/Pause button was pressed and the washer was set to Pause. Press Start
button again to restart the cycle.
Step 3
• Close lid.
NOTE: Unit will not start
with lid open if Auto is
selected except on Bulky
Items/Bulky cycle.
• Select wash cycle.
• Select wash options, including Deep Rinse/
Extra Rinse/2nd Rinse option (depending
on model) when using fabric softener.
• Select options.
• Select load size (on some models).
Step 4
• Press
Start.
49-3000318 Rev 0