Lexmark C912 Quick Reference

Quick Reference

Printer menu overview

Color Menu
LocalTalk Menu PCL Emul Menu
Print Mode LocalTalk Port Font Source
Color Correction
PCL SmartSwitch Font Name
Toner Darkness PS SmartSwitch Point Size
Manual Color
NPA Mode Pitch
LocalTalk Buffer Symbol Set
Job Buffering Orientation
Finishing Menu NPA Hosts Lines per Page
LocalTalk Name A4 Width
Duplex
LocalTalk Addr Tray Renumber
Duplex Bind
LocalTalk Zone Auto CR after LF
Copies
Auto LF after CR
Blank Pages
Collation
Paper Menu
Separator Sheets
PostScript Menu
Paper Source
Separator Source
Print PS Error
Paper Size
Multipage Print
Font Priority
Paper Type
Multipage Order
Image Smoothing
Custom Types
Multipage View
Universal Setup
Multipage Border
Output Bin
Staple Job
Serial Menu
Configure Bins
Staple Prime Src
Assign Type/Bin
PCL SmartSwitch
Hole Punch
Substitute Size
PS SmartSwitch
Off set Pages
Configure MP
NPA Mode
Paper Weight
Serial Buffer
Infrared Menu
Paper Loading
Job Buffering
Infrared Port RS-232/RS-422
PCL SmartSwitch
RS-422 Polarity
Parallel Menu
PS SmartSwitch Serial Protocol
NPA Mode PCL SmartSwitch
Robust XON
PS SmartSwitch
Infrared Buffer Baud
NPA Mode
Job Buffering Data Bits
Parallel Buffer
Window Size Parity
Job Buffering
Transmit Delay Honor DSR
Advanced Status
Max Baud Rate
Protocol
Honor Init
Utilities Menu
Job Menu
Parallel Mode 1
Print Menus
Parallel Mode 2
Cancel Job
Print Net <x> Setup
MAC Binary PS
Confidential Job
Print Fonts
Held Jobs
Print Directory
Reset Printer
Print Demo
Network Menu
Reset Active Bin
Color Samples
Prime Stapler PCL SmartSwitch
Factory Defaults
Cancel Fax
PS SmartSwitch
Remove Held Jobs
NPA Mode
Format Flash
Network Buffer
Defragment Flash
Job Buffering
Format Disk
MAC Binary PS
Job Acct Stat
Std Net Setup
Print Alignment
Network <x> Setup
Hex Trace

Using the operator panel

Press Menu to:
• Enter the menus from the Ready state.
• Scroll through menus or values.
• Increase or decrease a numerical value.
•
Display the Job Menu or the Supplies
Menu while the printer is busy.
Press Select to:
• Select the item on the second line of the display.
• Save the selection as a new default setting.
Press Return to back up to the previous menu level.
Press Go to:
• Exit the menus and return to the Ready state.
• Clear messages.
Press Stop to temporarily stop all print activity without losing data.

Canceling a print job

To cancel a print job after it has started printing:
1
Press Menu
2
Press Menu
Setup Menu
Printer Language
Power Saver
Printing a menu settings page
Resource Save
Download Target
Print Timeout
To verify Paper Size and Paper Type settings, and check installed options and
Wait Timeout
memory, print a menu settings page:
Auto Continue
Jam Recovery
1
Press
Page Protect Menu
Display Language
2
Press Menu
Alarm Control
Printer Usage
settings page prints.
Staple Alarm
Hole Punch Alarm
Job Accounting
Start Page Understanding printer messages
The following table lists some typical operator panel messages you may
Supplies Menu
encounter and the action you can take to clear them. For more information on
<color> Toner
Color Photo Devs
these or other printer messages, refer to the publications CD.
Black Photo Dev
Fuser
Belt
Message
Supplies Life
Replace Supplies
33 Tray x Config Error
The optional Heavy Media
USB Menu
Tray is incorrectly installed.
PCL SmartSwitch
PS SmartSwitch
NPA Mode
USB Buffer
Job Buffering
37 Insufficient Memory
MAC Binary PS
The printer memory is not
sufficient and cannot
Fax Menu
continue processing print
Fax Setup
Fax Logs
jobs, or there is not enough
Fax Send
memory to restore jobs from
Fax Receive
the printer's hard disk.
38 Memory Full
The printer is processing
data, but the memory used
to store pages is full.
39 Complex Page
4
1 2 3 The page may not print
Select Return
Menu
correctly because the print
information on the page is
too complex.
5 6
41 Open Bin 1 Exit Tray
Go Stop
A print job was sent to the
face-up (Bin 1) output tray on
the left side of the machine,
but the tray is closed.
until you see Job Menu, and then press Select .
until you see Cancel Job, and then press Select .
until you see Utilities Menu, and then press
Select
until you see Print Menus, and then press Select
Action
• Remove the Heavy Media Tray and reinstall it or install
the standard Tray 1.
• Install the Heavy Media Tray into the Tray 1 location.
Printing from the Heavy Media Tray is only supported
from the Tray 1 location.
• Press Go to clear the message. The printer deletes
held jobs until there is enough printer memory to
process the current job.
• Press Stop to clear the message without deleting any
held jobs. The current job may not print correctly.
• Press Menu to open the Job Menu, and then press
Select to cancel the current job.
Note: The messages 37 Insufficient Memory and
Held Jobs may be lost or Held Jobs May Not Be
Restored alternate on the display.
• Press Go to clear the message and continue printing
the job. The job may not print correctly.
• Press Menu to open the Job Menu, and then press
Select to cancel the current job.
• Press Go to clear the message and continue printing
the job. The job may not print correctly.
• Press Menu to open the Job Menu, and then press
Select to cancel the current job.
• Open Bin 1 to clear the message and continue
printing.
• Press Go to clear the message and continue printing.
The paper is diverted to the Standard output bin.
Message Action
• Press Go to clear the message.
80 Fuser Life Warning
It is time to replace the fuser. • Install a new fuser: Press Select and the Printer
Note: When the fuser's life has expired, the display
alternates between the 80 Fuser Exhausted (or 80
Fuser/Belt Exhausted) and Select = Replace
messages. You must replace the fuser (after pressing
Select) to continue printing.
• Press Go to clear the message.
80 Belt Life Warning
.
It is time to replace the • Install a new transfer belt: Press Select and the
. The menu
transfer belt.
Note: When the transfer belt's life has expired, the display
alternates between the 80 Belt Exhausted (or 80
Fuser/Belt Exhausted) and Select = Replace
messages. You must replace the transfer belt (after
pressing Select) to continue printing.
• Press Go to clear the message.
84 <color> Photo Dev
Life Warning
• Install a new <color> photodeveloper(s).
It is time to replace one or
Note: When the photodeveloper's life has expired, the
more specified
message 84 <color> Photo Dev Exhausted or 84 All
photodevelopers.
Photo Devs Exhausted appears. Press Go to clear this
message or replace the indicated photodeveloper(s).
• Press Go to clear the message.
85 Coating Roll Life
Warning
• Install a new oil coating roll
It is time to replace the oil
Note: The message Replace Oil Coating Roll may
coating roll.
be displayed if the black toner cartridge was replaced, but
the oil coating roll was not replaced.
• Press Go to clear the message.
88 <color> Toner Low
It is time to replace one or • Install a new <color> toner cartridge.
more toner cartridges.
Note: When the toner cartridge is empty, the message
88 <color> Toner Empty appears. The toner cartridge
must be replaced to continue printing. If the black
cartridge is empty, a second message, Replace Oil
Coating Roll, is also displayed, where both the black
cartridge and oil coating roll must be replaced.
Clear the paper jam and then press Go.
2<xx> Paper Jam
A paper jam is detected. Refer to the Clearing Jams sheet or the publications CD for
information about clearing paper jams.
Turn the printer off and check all cable connections. Turn
900-999 Service Message
the printer back on. If the service message recurs, call for
Messages 900–999 relate to
service and report the message number and description of
printer problems that may
the problem.
require service.
P/N 12N0573
*12N0573*
E.C. 548073
© Lexmark International, Inc.
Ready for Maintenance message is displayed. Turn
the printer off and replace the fuser.
Printer Ready for Maintenance message is
displayed. Turn the printer off and replace the belt.
12N0573 Printed in U.S.A.
03/03
All rights reserved.