Table of Contents
Advertisement
en Rapid heating
8.3 Starting operation
You must start each operation.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures above
120 °C, this will damage the enamel.
Do not use the appliance if there is water on the
▶
cooking compartment floor.
Wipe away any water on the cooking compartment
▶
floor before operation.
Press to start.
▶
a The settings, the running time, the display ring and
the heating line appear in the display.
8.4 Pausing or cancelling operation
You can briefly pause operation and then continue. If
you cancel operation completely, the settings will be re-
set.
To pause operation briefly:
1.
Briefly press .
‒
To continue operation, press .
‒
To cancel operation completely, press and hold
2.
for approx. 3 seconds.
a Operation will stop and all the settings will be reset.
8.5 Setting the operating mode
Once you have switched on the appliance, it suggests
an operating mode, e.g. types of heating.
If you want to use a different operating mode to the
1.
one suggested, press
a The list of operating modes is displayed.
→ "Operating modes", Page 10
Press the operating mode that you want to use.
2.
To implement other settings, press the relevant text
3.
fields.
Use the control ring to change the values.
4.
Press to start.
5.
8.6 Setting the type of heating and
temperature
Requirement: The operating mode "Types of heating"
has been selected.
9 Rapid heating
To save time, you can shorten the preheating time for
set temperatures of 100 °C and higher.
You can use rapid heating for the following types of
heating:
¡ 4D hot air
¡ Top/bottom heating
9.1 Setting rapid heating
To ensure an even cooking result, do not place the
food in the cooking compartment until rapid heating
has come to an end.
Note: Do not set a cooking time until rapid heating has
come to an end.
14
.
Press the type of heating that you want to use.
1.
If you cannot see the type of heating in the touch
displays, use the control ring to scroll though the se-
lection list.
a The temperature is highlighted in white.
Use the control ring to set the temperature.
2.
Press to start.
3.
a The appliance starts heating.
a The target temperature, the time and how long the
appliance has already been in operation are shown
in the display.
When the food is ready, press
4.
ance off.
Tip: The most suitable type of heating for your food
can be found in the description of the type of heating.
Note: You can also set a cooking time and end time on
the appliance.
→ "Time-setting options", Page 15
Changing the type of heating
When you change the type of heating, the other set-
tings will also be reset.
Press to pause operation.
1.
Press "Types of heating".
2.
Press the type of heating that you want to use.
3.
a The corresponding default temperature appears in
the display.
Changing the temperature
Once operation has started, you can change the tem-
perature directly.
Use the control ring to change the temperature.
▶
a The temperature is applied immediately.
8.7 Displaying information
In most cases, you can call up information about the
function that you have just started. The appliance dis-
plays some information, e.g. to ask you to do/confirm
something or to issue a warning, automatically.
Press .
1.
a If available, information is displayed for a few
seconds.
Use the control ring to scroll through longer pas-
2.
sages of text.
Set a suitable type of heating and a temperature of
1.
at least 100 °C.
Press "Rapid heating".
2.
a The text field shows "On".
Press to start.
3.
a Rapid heating starts.
a When rapid heating has come to an end, an audible
signal sounds. The text field shows "Off".
Place the food in the cooking compartment.
4.
Cancelling rapid heating
Press "Rapid heating".
▶
a The text field shows "Off".
to switch the appli-
Advertisement
Table of Contents
