Graco 234413 Instructions Manual
  1. Manuals
  2. Brands
  3. Graco Manuals
  4. Industrial Equipment
  5. 234413
  6. Instructions manual
Graco 234413 Instructions Manual

Graco 234413 Instructions Manual

2-liter pressure cup
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Instructions - Parts List
2-Liter Pressure Cup
Model 234413
50 psi (345 kPa, 3.4 bar) Maximum Fluid Pressure
160 psi (1.1 MPa, 11 bar) Maximum Air Inlet Pressure
This manual contains important warnings
and information. Read and keep for
reference.
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441
Copyright 2003, Graco Inc. is registered to I.S. EN ISO 9001
309925B

Advertisement

Table of Contents
loading

Related Manuals for Graco 234413

Summary of Contents for Graco 234413

  • Page 1 160 psi (1.1 MPa, 11 bar) Maximum Air Inlet Pressure This manual contains important warnings and information. Read and keep for reference. Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441 Copyright 2003, Graco Inc. is registered to I.S. EN ISO 9001...

  • Page 2: Manual Conventions

    • Check equipment daily. Repair or replace worn or damaged parts immediately. • Do not alter or modify equipment. • Use equipment only for its intended purpose. Call your Graco distributor for information. • For professional use only. • Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

  • Page 3: Pressure Relief Procedure

    Set-Up WARNING TOXIC FLUID OR FUMES HAZARD Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swal- lowed. • Read MSDS’s to know the specific hazards of the fluids you are using. •...

  • Page 4: Installation

    Air Supply Air Adjusting Valve (optional) Fluid Line Atomizing Air Air Compressor Air Supply Hose Model 234413 2-liter Pressure Cup Setting Gun Air Pressure Material Preparation Set the gun air pressure regulator for the minimum Follow manufacturer’s directions for mixing and pressure needed to atomize your fluid.

  • Page 5: Operation

    Operation Operation 1. Pull out regulator knob and turn fully counter-clock- Maximum cup pressure is 50 psi (345 kPa, 3.4 wise. Open relief valve on cup lid (counter-clock- bar). wise). 7. To decrease paint flow, pull out regulator knob and 2.

  • Page 6: Maintenance

    Maintenance Maintenance Cleaning the Cup 1. Follow Pressure Relief Procedure, page 3. 2. Turn cup pressure regulator to full “off” position, counter-clockwise. 3. Open cup lid by turning counter-clockwise. 4. Pour out any remaining material and add compatible solvent. 5. Repeat steps 3 and 4 in Operation, page 5. Spray until clean solvent appears.

  • Page 7: Troubleshooting

    Troubleshooting Troubleshooting Problem Cause(s) Solution(s) Excess pressure in cup. Leak at regulator valve assembly Replace Gauge registering wrong Replace Safety valve setting too high Replace Valve spring broken or distorted Replace Diaphragm damaged Replace Insufficient pressure in cup Check valve stuck shut Clean or replace Safety valve setting too low Replace...
  • Page 8 Parts Parts Model 234413, 2-Liter Pressure Cup 2-Liter Pressure Cup 234413 Part No. Description 234434 REGULATOR, air pressure; see Manual 309924 for parts U22801 TUBE, fluid U22802 LID, cup U22803 RING, cup U22807 GASKET, lid U22820 VALVE, safety U22850 U22825...

  • Page 9: Technical Data

    Technical Data Technical Data Maximum regulated cup pressure (fluid pressure) ..50 psi (345 kPa, 3.4 bar) Maximum air inlet pressure......160 psi (1.1 MPa, 11 bar) Safety valve release .

  • Page 10: Graco Standard Warranty

    Graco distributor. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.

Table of Contents