Garmin GPSMAP 10X2 Series Installation Instructions Manual page 2

GPSMAP 10X2/12X2 SERIES
®
INSTALLATION
INSTRUCTIONS
Important Safety Information
WARNING
Failure to follow these warnings, cautions, and notices could result in personal
injury, damage to the vessel or device, or poor product performance.
See the Important Safety and Product Information guide in the product box for
product warnings and other important information.
When connecting the power cable, do not remove the in-line fuse holder. To
prevent the possibility of injury or product damage caused by fire or
overheating, the appropriate fuse must be in place as indicated in the product
specifications. In addition, connecting the power cable without the appropriate
fuse in place voids the product warranty.
CAUTION
Always wear safety goggles, ear protection, and a dust mask when drilling,
cutting, or sanding.
To avoid possible personal injury or damage to the device and vessel,
disconnect the vessel's power supply before beginning to install the device.
To avoid possible personal injury or damage to the device or vessel, before
applying power to the device, make sure that it has been properly grounded,
following the instructions in the guide.
NOTICE
For the best possible performance, the device must be installed according to
these instructions.
When drilling or cutting, always check what is on the opposite side of the
surface to avoid damaging the vessel.
Read all installation instructions before proceeding with the installation. If you
experience difficulty during the installation, contact Garmin
Contacting Garmin Support
• Go to support.garmin.com for help and information, such as product
manuals, frequently asked questions, videos, and customer support.
• In the USA, call 913-397-8200 or 1-800-800-1020.
• In the UK, call 0808 238 0000.
• In Europe, call +44 (0) 870 850 1241.
Software Update
You may need to update the chartplotter software after installation. For the
instructions on how to update the software, see the owner's manual at
www.garmin.com/manuals/GPSMAP10x2-12x2.
Tools Needed
• Drill
◦ Bail mount: drill bits appropriate for the surface and hardware
◦ Flush mount: 14 mm (
nut plate), or 3.2 mm (
• #2 Phillips screwdriver
• Jigsaw or rotary tool
• File and sandpaper
• Marine sealant (recommended)
Mounting Considerations
This device should be mounted in a location that is not exposed to extreme
temperatures or conditions. The temperature range for this device is listed in
the product specifications. Extended exposure to temperatures exceeding the
specified temperature range, in storage or operating conditions, may cause
device failure. Extreme-temperature-induced damage and related
consequences are not covered by the warranty.
When selecting a mounting location, you should observe these considerations.
• The location should provide optimal viewing as you operate your boat.
• The location should allow for easy access to all device interfaces, such as
the keypad, touchscreen, and card reader, if applicable.
• The location must be strong enough to support the weight of the device
and protect it from excessive vibration or shock.
• To avoid interference with a magnetic compass, the device should not be
installed closer to a compass than the compass-safe distance value listed
in the product specifications.
• The location must allow room for the routing and connection of all cables.
• The location must not be a flat, horizontal surface. The location should be
in a vertical angle.
The location and viewing angle should be tested before you install the
device. High viewing angles from above and below the display may result
in a poor image.
Bail Mounting the Device
If you are mounting the bracket on fiberglass with screws, it is recommended
to use a countersink bit to drill a clearance counterbore through only the top
gel-coat layer. This will help to avoid cracking in the gel-coat layer when the
screws are tightened.
You can use a bail mount bracket (not included) to bail mount the device on a
flat surface.
1
Using the bail-mount bracket
Product Support.
®
2
Drill the pilot holes.
3
Using appropriate mounting screws (not included), secure the bail-mount
bracket to the mounting surface.
9 1 9
/ in.), 6 mm ( / in.) and 3.6 mm ( /
16 4 64
1
/ in.) drill bit (with no nut plate)
8
NOTICE
NOTICE
as a template, mark the pilot holes.
Printed in Taiwan
October 2020
190-02145-02_0C
in.) (with