Advertisement
Congratulations, and thank you for choosing the scala rider Q2 Bluetooth® Headset for bikers. This Manual will help you operate the headset, but you should first familiarize yourself with the Bluetooth functionality of your cellular phone and/or GPS device before using the scala rider Q2.
The retail box of the scala rider Q2 contains one headset unit. When paired with another scala rider Q2, the headsets can be used as an Intercom at a range of up to 1,640 ft (500m), subject to terrain and external conditions.
The scala rider Q2 offers the following uses:
The scala rider Q2 can establish an audio connection with one Bluetooth device at a time. Please read the section "Using the Headset" to see how you can switch the audio connection between the paired devices.
* Mobile phones that do not support the Bluetooth Handsfree profile may prevent you from using the Redial and Call Reject features
** Full duplex calls allow you to speak and hear the other party speak simultaneously
NOTE: The scala rider Q2 is also available in a cord-mounted microphone version to better fit certain full-faced helmets with tight chin sections.
Wall Charger
Allen Wrench
Velcro Pads
MP3 Cable
MP3 Cable Holder
Glue Plate
Pre-moistened Towelette
Carry-Pouch
Microphone Sponges
Flat sponge for full-face helmets and round sponge for other helmet types
User Guide, including Warranty and Registration form
The scala rider Q2 is a water-resistant device, designed for use under moderate rain or snow conditions.
However, the headset is not waterproof and should not be used under severe weather conditions. The cover tongue protecting the Charging Jack should be kept tightly closed at all times to prevent moisture from entering the device.
Make sure that the headset is fully charged for at least five hours before initial use.
The scala rider Q2 can be paired with up to two other headsets for Intercom communication, referred to in this guide as:
Primary Buddy
and
Secondary Buddy
Pairing is a one time process. Once the headsets are paired during this Setup Procedure, they will remain paired and automatically recognize each other whenever they are within range.
NOTE: The scala rider Q2 allows you to speak via Intercom to one Buddy headset at a time.
NOTE: If the Pairing process is not completed within one minute the headset will return to Standby mode.
Once you have paired the Main scala rider Q2 to the Primary Buddy headset, repeat the procedure above to pair the Main scala rider Q2 to the Secondary Buddy headset.
NOTE: The Main scala rider Q2 is able to communicate with either the Primary Buddy or the Secondary Buddy. The Primary Buddy and Secondary Buddy are not able to communicate directly via Intercom.
NOTE:If the Pairing process is not completed within one minute the headset will return to Standby mode.
There are two ways that the scala rider Q2 can be used for Driver-toPassenger communication.
To Pair the two headsets:
NOTE: If the Pairing process is not completed within one minute the headset will return to Standby mode.
NOTE: When using an earlier scala rider headset as a Passenger headset, Voice Connect Intercom can be initiated only by the scala rider Q2 headset. Manual Connect Intercom can be initiated from either headset by pressing the MC button for scala rider Q2 and CTRL button for any earlier scala rider headset.
You can delete all of the headset's Intercom pairings at any time.
If you have a Bluetooth enabled mobile phone and would like to make and receive phone calls using the scala rider Q2, you must first pair your headset to the mobile phone.
NOTE: If you have a compatible Bluetooth GPS device you wish to use with the scala rider Q2, please skip this step, and continue ahead to STEP 4: SET UP FOR BLUETOOTH GPS DEVICE.
Pairing is a one time process. Once the headset is paired to a specific mobile phone during this Setup Procedure, they will remain paired and automatically recognize each other whenever they are within range. If the connection between the phone and headset is lost, tap the CTRL button to reconnect the devices.
NOTE: If the Pairing process is not completed within two minutes the headset will return to Standby mode.
With some mobile phones, you may need to tap the CTRL button to connect the headset to the phone after pairing is complete. The scala rider Q2 headset will automatically connect to the last phone connected to the headset.
If you have a Bluetooth enabled GPS device and would like to transmit navigation instructions and sounds from the GPS device through the headset's speakers, you must first pair your headset to the GPS device.
NOTE: Not all Bluetooth enabled GPS devices allow connections to Bluetooth headsets like the scala rider Q2. Please consult your GPS device's User Manual for more information.
NOTE: If the Pairing process is not completed within two minutes the headset will return to Standby mode.
The Helmet Clamp must be attached to the left side of the helmet. Once attached, the headset unit can be mounted or released from the Helmet Clamp at any time. If you wish to connect your MP3 player to your headset, please refer first to the assembly instructions listed in section: USING THE MP3 PLAYER WITH YOUR HEADSET. There are two methods that can be used in order to attach the Clamp onto the helmet:
Standard Method: Recommended for most helmet types.
Glue Plate Method: Recommended for helmets to which the standard method cannot be applied, using the Glue Plate included in the box.
If you have purchased a helmet clamp version with the corded microphone, please refer to section ATTACHING THE CORDED MICROPHONE CLAMP ON A FULL-FACED HELMET.
You have the option to glue the Helmet Clamp onto your helmet, when the above standard method cannot be used, or in case you prefer to secure the Helmet Clamp with adhesive glue. This option has been successfully used for a range of high end helmets.
NOTE: While we have no reason to believe that the gluing option might negatively affect any helmet, Cardo does not assume any responsibility to that affect, irrespective of its nature and circumstances. The Glue Plate is offered as a free option that you may choose to use at your own risk and subject to renouncement of any future claims.
This process can be done only once!
If you have purchased a helmet clamp version with the corded microphone, please proceed as follows:
If you are using the corded microphone version, you must first make sure your helmet clamp is attached to your helmet as described in previous section (ATTACHING THE CLAMP ON THE HELMET). Clean the exact spot on the internal padding of the helmet, opposite your mouth, where the microphone will be placed and proceed as follows.
Attach the speakers to the Velcro inside your helmet opposite your ears (short speaker cord for the left ear [A] and the long speaker cord [B] for the right ear). You may want to use the supplied Velcro pad.
Using two speakers inside the helmet may be prohibited in certain jurisdictions. If this is the case, you should tuck away the long corded speaker underneath the helmet padding as follows: Lead the speaker cord [B] alongside the rim of the padding to the right side and then back to the left side, near speaker [A]. Then place the speaker [B] underneath the padding.
Slide the headset downwards along the sliding panel until a clicking sound indicates that the headset is locked in place.
Your headset can be removed for charging and storage by pressing your finger gently against the tab and sliding the headset up with the other hand.
We recommend that you remove the headset from the helmet when not in use.
GENERAL FUNCTIONS | |
DESIRED RESULT: | REQUIRED ACTION: |
Turn on the headset | Press the CTRL Button steadily for at least three seconds |
Turn off the headset | Press the CTRL Button steadily for at least three seconds |
Increase the volume | Short press the Volume Up Button |
Decrease the volume | Short press the Volume Down Button |
AGC (Automatic Gain Control): In addition to manual Volume Control, the scala rider Q2 will automatically increase and reduce its volume according to ambient noise and driving speed.
The different Audio Sources that are connected to the scala rider Q2 are prioritized as follows:
Highest
Lowest
A high priority Audio Source will always interrupt any lower priority Audio Source.
i.e. Mobile phone call interrupts Intercom call
Intercom call interrupts FM Radio
To start a Buddy Intercom call with the Primary Buddy while the headset is on Standby you can either:
Start talking
A Buddy Intercom call will be established and stay on until both sides are quiet for 30 seconds.
OR
Single tap the MC Button
A Buddy Intercom call will be established. To end the Buddy Intercom call, single tap the MC Button again.
Double tap the MC Button
A Buddy Intercom call will be established. To end the Buddy Intercom call, double tap the MC Button again.
NOTE: When using a scala rider Headset (not a Q2 version) as a Passenger headset, Voice Connect Intercom can be initiated only by the scala rider Q2 headset. Manual Connect Intercom can be initiated from either headset.
Failed Connection: On the scala rider Q2, if you attempt to start a Buddy Intercom call with a Buddy that is already on a Phone/GPS/ Intercom call, you will hear a double beep indicating the Buddy is busy.
Reconnecting the Intercom: If the scala rider Q2 and its Intercom Buddy headset go out of range and disconnect from each other, the scala rider Q2 will automatically try to reconnect to its Intercom Buddy for five minutes.
You can manually reconnect at any time by pressing the MC Button (single tap for Primary Buddy and double tap for Secondary Buddy).
If you are not speaking with any one, once the other party tries to initiate a Buddy Intercom call, the call will begin immediately.
First, make sure your microphone is located properly in front of the center of your mouth.
The scala rider Q2 is designed for use in loud environments. Please make sure to test the Intercom functionality in a LOUD environment, such as next to an idling motorcycle.
Please also verify that the headsets were paired together properly by following the instructions in the relevant Setup sections.
The headset's Voice Connect feature allows you to start a Buddy Intercom call by simply speaking into the microphone. You can define which of the two Buddy headsets you wish to connect to when using Voice Connect Intercom.
NOTE: The Primary Buddy has priority by default.
To toggle the Voice Connect Intercom between Primary and Secondary Buddy:
Press and hold the Volume Up Button for three seconds and you will hear a beep:
Press and hold the Volume Up and Down Buttons simultaneously until you hear a beep. The default status is Voice Connect enabled.
NOTE: The Enable/Disable Voice Connect feature affects the Intercom functionality only.
PHONE FUNCTIONS | |
Answer a call | Short press the CTRL Button or speak loudly any word of your choice during an incoming call. |
Reject a call | Short press the MC Button or remain silent for 15 seconds during an incoming call. |
Terminate a call | Short press the CTRL Button to end a call. |
Voice Dial | During Standby, short press the CTRL Button and state the name of the person you wish to call. This feature is supported only by mobile phones that support the Voice Dial feature. |
Redial | Press and hold the Volume Down Button for three seconds during Standby. |
NOTE: If your Bluetooth mobile phone is paired to a Bluetooth GPS device, not directly to the scala rider Q2, some of the above Phone functions may not be compatible.
When the headset is on an active phone call, any Buddy Intercom call request will be rejected automatically.
Once the phone call audio link drops, you can initiate and accept Buddy Intercom calls.
None | Headset is off |
Alternating Red/blue flashes | Mobile phone/GPS Pairing mode |
Rapid Red flashes | Intercom Pairing mode |
1 blue flash every 3 seconds | Standby – No call is in progress |
2 blue flashes every 3 seconds | Call being initiated or in progress / FM Radio ON |
1 red flash every 3 seconds | Battery is low |
2 red flashes every 3 seconds | Call being initiated or in progress / FM Radio ON and battery is low |
Solid red | Headset is being charged |
Your headset is equipped with a high-quality FM Radio receiver. This section explains how to enjoy the functions of the FM Radio.
The scala rider Q2 enables you to listen to FM Radio while you are not receiving audio from another audio source.
While listening to the radio, you do not have to worry about missing any calls, as the headset automatically mutes the FM Radio and switches to Bluetooth headset operation when an incoming call is received, or when you decide to initiate a call. When the conversation is over, the headset automatically tunes back in to the FM Radio.
While no call is on the headset (either mobile phone call or Intercom call), press and hold the MC Button on your headset for three seconds to turn on the radio. The radio tunes in to the last radio station you were listening to. With some phones you should wait a few seconds after ending a call before turning on the Radio.
While the radio is turned on, press and hold the MC button for three seconds to turn the Radio off.
There are six pre-set Radio stations available on your scala rider Q2.
While the Radio is on, tap the MC Button to cycle between saved stations.
While the Radio is on, press and hold the Volume Up or Volume Down Button for three seconds or until you hear the next station on your headset.
Pressing Volume Up will search upwards (higher frequency). Pressing Volume Down will search downwards (lower frequency). Once a station is found, searching stops and you can hear the station.
To save this station, refer to the following section.
To continue searching, press the Volume Up or Volume Down Button again for three seconds.
You may still continue to listen to the current unsaved station. Pressing the MC Button in this case will switch to the next saved station.
The FM Radio is equipped with a memory capacity of six stations.
If you don't save the station, the Radio will exit search mode without saving the current station. You can still continue to listen to the current unsaved station. Tapping the MC Button in this case will move to the next saved station.
Your scala rider Q2 headset can be connected to an MP3 player device by plugging it to the Helmet Clamp's jack with the MP3 cable.
At your option, you may further secure the MP3 cable by using the MP3 cable holder. For this purpose please proceed as follows:
NOTE: Operate the MP3 Player device by using its buttons (FF/REW/PLAY/ PAUSE).
Volume can only be adjusted through the MP3 Player.
Any other audio connection will automatically mute the MP3 Player. The audio signal will return only when headset is once again in Standby mode.
For additional information please visit our website at www.cardosystems.com
FAQ: www.cardosystems.com/support/faq or contact us at:
support@cardosystems.com
Phone:
USA and Canada – + 1-800-488-0363
International – +4989 450 36819
15.21
You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user's authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Industry Canada (IC) Statement
15.21
You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user's authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the IC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The scala rider Q2™ headset (the "Product") is in conformity with the following essential requirements of Council Directive 1999/5/EC (referred to as R&TTE Directive): Articles 3.1a, 3.1.b and 3.2. The Product is manufactured in accordance with Annex II of the above directive.
The scala rider Q2™ headset is compliant with and adopts the Bluetooth® Specification 2.0 and has successfully passed all interoperability tests that are specified in the Bluetooth® specification. However, interoperability between the device and other Bluetooth®-enabled products is not guaranteed.
By using the scala rider Q2 you will waive substantial legal rights including the right to sue. Please read the following carefully before using the device. If you do not accept all terms of this agreement, you should immediately return the product for a full refund. By using the headset you agree to be bound to this agreement and forfeit the right to sue.
Using a communication device while riding a motorcycle, scooter, moped, ATV, quadbike or any other vehicle or equipment, whether on land, water or air (jointly referred to as "Vehicle") requires your complete and undivided attention. Cardo Systems, Inc., including its Officers, Directors, Affiliates, Parent Company, Representatives, Agents, Contractors, Sponsors, Employees, Suppliers and Resellers (jointly referred to as the "Company" or "Cardo") strongly advises you to take all necessary precautions and remain alert to the traffic, weather and road conditions if you choose to use the scala rider Q2 headset, including all derivative models irrespective of its commercial name or branding (the "Device"), and stop your Vehicle on the roadside prior to initiating or receiving calls. Any publications, advertisements, announcements or similar notes that refer to using the Device while riding a Vehicle are solely intended to address its technical capabilities and should not be misconstrued as if encouraging users to operate the Device while actively involved in traffic.
By way of purchasing this Device and not returning it for a full refund (see below), you are irrevocably releasing, indemnifying from any liability, loss, claim and expense (including attorneys fees) and holding Cardo harmless for any bodily injuries, harm or death as well as losses or damages in goods, to any Vehicles including your own, or to any property or asset that belong to you or to third parties, any of which may result from using the Device under any circumstances or conditions and irrespective of jurisdiction. Cardo will not be responsible for any physical damages, irrespective of reasons, conditions or circumstances, including malfunctioning of the Device, and all risks associated with operating it rest solely and entirely with the user of this Device, irrespective of whether the Device is used by the original purchaser or any third party.
Cardo hereby notifies you that using this Device may also be in contravention to local, federal, state or national laws or regulations, and that any use of the Device is entirely at your sole risk and responsibility.
CARDO DISCLAIMS ALL EXPRESS AND IMPLIED WARRANTIES WITH REGARD TO THE ENCLOSED DEVICE, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NONINFRINGEMENT. THE DEVICE AND ITS ACCESSORIES ARE PROVIDED "AS IS" AND "AS AVAILABLE" WITHOUT WARRANTY OF ANY KIND BEYOND THOSE ASSUMED IN THE ENCLOSED MANUAL.
IN NO EVENT SHALL CARDO BE LIABLE FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THE DEVICE, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. YOU ACKNOWLEDGE AND AGREE THAT THE LIMITATIONS SET FORTH ABOVE ARE FUNDAMENTAL ELEMENTS OF THIS AGREEMENT AND THE DEVICE WOULD NOT BE PROVIDED TO YOU ABSENT SUCH LIMITATIONS. SOME STATE STATUTES MIGHT APPLY REGARDING LIMITATION OF LIABILITY.
IF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE CONDITIONS, YOU MAY RETURN THIS DEVICE TO THE STORE FOR A FULL REFUND, PROVIDED THAT YOU DO SO NO LATER THAN 7 BUSINESS DAYS FOLLOWING THE PURCHASE OF THE DEVICE (proof of purchase required) AND SUBJECT TO THE RETAIL BOX AND ALL ACCESSORIES BEING COMPLETE AND INTACT. WHEN DOING SO, PLEASE REFER TO THIS SECTION. BY NOT RETURNING THE DEVICE FOR REFUND WITHIN THE PERIOD PROVIDED, YOU ARE EXPLICITLY IN AGREEMENT WITH THE ABOVE, AND RENOUNCE ALL RIGHTS TO FUTURE CLAIMS AND DEMANDS AGAINST CARDO AS DEFINED ABOVE.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the Scala rider Q2 that isn't answered in the manual? Leave your question here.