ADC HiGain H2TU-C-202 User Manual page 24

Provisioning
Standard Config Menu
Options
Network Loopback Pattern
(NLBP)
Power Back Off - Network
(PBON)
See "Power Back Off
Customer (PBOC) and Power
Back Off Network (PBON)
Options" on page 18.
Power Back Off - Customer
(PBOC)
See "Power Back Off
Customer (PBOC) and Power
Back Off Network (PBON)
Options" on page 18.
(a) FRMG, DS1, and LBTO are read-only options on the maintenance terminal. Options can only be changed by the dip-switches
on the board.
ADC Config
Menu Options
(a)
Line Power Feed (PWRF)
Remote Provisioning (RTPV)
Bipolar Violation Transparency
(BPVT)
See "Bipolar Violation
Transparency (BPVT) Option"
on page 18.
DS1 BER (DBER)
See "DS1 BER (DBER) Option"
on page 18.
HDSL2 BER Threshold (HBER)
See "HDSL2 BER Threshold
(HBER) Option" on page 19.
Special Loopback Mode
(SPLB)
See "Special Loopback (SPLB)
Mode" on page 43.
SmartJack Loopback (LPBK)
16
Table 6. H2TU-C Standard Config Menu Options (Continued)
Selection Description
AIS Enables the H2TU-R to transmit an AIS toward CI for any network loopback. For
priority resolution, see
LOS Enables the H2TU-R to transmit an LOS toward CI for any network loopback.
DEF Configures the power output levels of the H2TU-C network unit toward the
customer to comply with the Default template as defined in Section 6.1.4.2 of ANSI
T1/E1.4.
ENH Configures the power output levels of the H2TU-C network unit toward the
customer to comply with the Enhanced template as defined in Section 6.1.4.2 of
ANSI T1/E1.4.
DEF Configures the power output levels of the H2TU-R customer unit toward the
network to comply with the Default template as defined in Section 6.1.4.2 of ANSI
T1/E1.4.
ENH Configures the power output levels of the H2TU-R customer unit toward the
network to comply with the Enhanced template as defined in Section 6.1.4.2 of
ANSI T1/E1.4.
Table 7. H2TU-C ADC Config Menu Options
Selection Description
OFF Disables powering to the HDSL2 pair.
ON Keeps the HDSL2 line voltage at nominal -180 Vdc.
ENA Enables provisioning at the H2TU-R remote unit
DIS Disables provisioning at the H2TU-R remote unit
ENA Enables HDSL2 CRC and BPV errors at the DS1 input to be converted into DS1 BPVs
at the DS1 output at the distant end. This makes HDSL2 transparent to BPVs.
DIS Disables BPV Transparency.
ENA Enables the fixed 24-hour DS1 BER threshold (10
DIS Prevents the generation of a system alarm due to DS1 BER.
1E-6 Front-panel alarm is displayed and the Status LED flashes red when the Block Error
Rate (BER) threshold exceeds 10
1E-7 Front-panel alarm is displayed and the Status LED flashes red when the Block Error
Rate (BER) threshold exceeds 10
NONE Prevents generation of a system alarm due to BER.
GNLB Configures the HDSL2 system to respond to the generic inband loopback codes.
A3LB Configures the HDSL2 system to respond to the inband loopback codes of the
Wescom addressable repeater.
ENA Enables the HDSL2 system to recognize all inband SmartJack (SMJK) loopback
commands.
DIS Configures the HDSL2 system to ignore all inband SmartJack loopback commands.
Figure 27 on page
-6
. BER is based on the definition of Bit Error Rate.
-7
.
June 6, 2003
LTPH-UM-1208-01
41.
-6
).
H2TU-C-202 List 7G
Continued