Table of Contents
Advertisement
32642_AVR41 Eng 04/03/1998 9:03 Side 18
If the
indicator is NOT illuminat-
AUTO
ed, tap the
button
Tuning
one frequency increment at a time, or
press and hold it to locate a specific
frequency. When the
TUNED
illuminates, the station is properly tuned
and should be heard with clarity. To
listen to the station in stereo, press the
button
Tuning Mode
indicator illuminates in the
STEREO
front panel display. If the
indicator does not light, although
is on the station is broadcasting
AUTO
in mono.
5. To select stations using the remote,
press the
Manual Tune
h
to select frequencies one at a time,
no matter about the selected Tuning
mode. After an FM station is selected and
if the
indicator is not lit, the
AUTO
button
Tuning Mode
pressed once to receive the station in
stereo, when available. Alternatively, the
››
Automatic Tune
i
may be used to scan only those
stations with sufficient strength for
proper reception, no matter if the
indicator is lit or not. If RDS Seek is
engaged these buttons will start the seek
for specific RDS stations (see page 19).
NOTE: When FM stereo reception is
weak, audio quality may be increased by
switching to mono mode by pressing the
button
Tuning Mode
indicator goes out.
STEREO
NOTE: When an FM station transmitting
RDS data is tuned the AVR41 will
automatically display the station name
respectivelly its program service (PS) that
can be any additional information. Press
the
button
k¸
Display
to view the frequency or other RDS
information (see page 19).
Operation
Preset Tuning
Ú
to advance
Up to 30 stations may be stored in the
AVR41's memory for easy recall using the
front panel controls or the remote.
indicator
To enter a station to the memory, first
tune the station using the steps outlined
above. Then:
˘
until the red
1. Press the
Memory
front panel. Note that the
STEREO
will illuminate and flash in the
information display.
2. Within five seconds, press the
Numeric Buttons Ô
the location where you wish to store this
buttons
››
/
‹‹
station's frequency. For two-digit
locations, such as 10-29, be certain to
enter the second digit within two seconds
of pressing the first number (while
is still flashing). To enter a station to
˘
must be
memory location "30, " press only the
button.
0
buttons
‹‹
/
3. The selected preset number will light
up in the information display just below
the word "PRESET".
AUTO
Recalling Preset Stations
• To manually select a station previously
entered in the preset memory, press the
Numeric Buttons Ô
the desired station's location as shown in
item 2 above.
˘
until the
• To manually tune through the list of
stored preset stations one by one, press
the
Preset/Disc Skip
on the remote. Press and hold the
buttons to skip through the preset
stations.
• To automatically scan through the
repeatedly
stations entered in the preset memory,
.
press the
P
Scan
18
panel or the
remote. The tuner will run through the
list of preset stations, stopping for five
seconds at each one. Press the
or
Scan
your desired station.
RDS Operation
button
Ó
on the
Your AVR41 is equipped with RDS (Radio
indicator
MEM
Data System), which brings a wide range
of information to FM radio. Now in use
in many countries, RDS is a system for
transmitting station call signs or network
information, a description of station
corresponding to
programme type, text messages about the
station or specifics of a musical selection
and the correct time.
As more FM stations become equipped
MEM
with RDS capabilities, the AVR41 will
serve as an easy-to-use centre for both
information and entertainment. This
section will help you take maximum
advantage of the RDS system.
RDS Tuning
When an FM station is tuned in and it
contains RDS data, the AVR41 will
automatically display the station's call
sign (with some private stations other
text between too). To tune only stations
corresponding to
broadcasting RDS data, press the
Tuning Mode
indicator illuminates in the front panel
display or the
until the display reads
10 seconds. Press the
buttons
e
‹ ›
on the front panel or
the remote, the display briefly will read
RDS ONLY
station transmitting RDS data. A few
seconds after this RDS station is tuned its
station name or programme service
information will be displayed.
button
3 3
on the front
button
p
on the
Scan
.
P
Scan
button again to stop the scan at
button
˘
until the RDS
3 4 u
button
RDS Seek
for
RDS ONLY
buttons
Ú
Tuning
i
on
››
‹‹
/
to advance to the next
Hide quick links:
Advertisement
Table of Contents
