Table of Contents
Advertisement
32642_AVR41 Eng 04/03/1998 9:02 Side 10
a Infrared Transmitters: An
infrared beam is transmitted from
these emitters when you press any
button on the remote. For best oper-
ation, always point the front of the
remote towards the sensor on the
AVR41 3 7 and do not obstruct this
area.
b Sleep: Press this button to place
the unit in the sleep mode. The dis-
play will dim and the unit will turn off
after the number of minutes shown
in the information display.
c Power Button: Press this button
to turn the AVR41 on or to put it in
standby (see page 15).
NOTE: In order for this button to
work, the AVR41 must first be placed
in the standby mode by pressing the
front panel Main Power Switch 1
until it is engaged and the ring sur-
rounding the Power switch 2 turns
amber.
d Input Select Buttons: Press
one of these buttons to choose an
input source.
NOTE: Automatic Power On: When
you press an Input Select Button
while the unit is in the Standby
Mode, the system will automatically
be turned on.
e Preset/Disc Skip: Press these
buttons to scan up or down through
the stations entered in the tuner
memory. The
›
button will also
advance the disc being played in
compatible Harman Kardon CD
changers.
f Cassette Control: These but-
tons control some transport func-
tions of compatible Harman Kardon
cassette decks. The
the deck or primary transport in play
or change the direction during play.
The
Î
±
button will place the deck
/
to Record/Pause or will pause the
deck during record. Press any of the
buttons f or g to start or
‹ ›
continue recording.
g Transport Control: These buttons
control the Play
, Pause
›
functions of compatible Harman
Í
Kardon CD or cassette players.
Remote Control Functions
h Manual Tune/Fast Forward/
Reverse: Press these buttons to
manually tune stations in any Tuning
Mode (see page 18). They may also
be used to put a compatible Harman
Kardon CD player or cassette deck
in the fast forward
‹‹
mode.
i Automatic Tune/Track Change:
Press these buttons to search sta-
tions with a strong enough signal for
acceptable stereo listening, no mat-
ter if Tuning Mode AUTO is select-
ed or not (see page 18). If RDS Seek
is on, they will search only stations
with the program type (PTY) select-
ed (see page 19). These buttons will
also change the disc track on com-
patible Harman Kardon CD players,
and engage the title search on cas-
sette decks.
NOTE: In order for the transport
controls ghi to function, you
must first press the Source Select
Button d for the device to be
controlled.
j Battery Compartment: Install
two "AA" batteries as shown on
page 9 to power the remote control.
k Display: Press this button to
change the display brightness from
normal to half to off (see page 15).
When the FM tuner is selected, this
button is also used to select the type
of RDS information to be displayed,
or press and hold during FM opera-
tion to dim the display (see pages
15/19).
NOTE: If CD was selected by the
remote control this remote button
may dim or turn on/off only the dis-
play of the linked CD player.
l Master Volume Control: Push
‹ ›
buttons put
the bar away from you to raise the
unit's volume, and press it towards
you to lower the volume.
m Mute: Press this button to
momentarily silence the speakers.
Note that the word MUTE will flash in
the information display along with
the Mute/Volume Indicator ı to
and Stop
remind you that the Mute function is
±
engaged. Press the button again to
return to the previously selected
listening level (see page 15).
10
n Center Boost: Press this button
to increase the level of the Centre
Channel for improved dialogue intel-
ligibility, or to turn the Centre Boost
circuit off. Note that a Red LED will
illuminate above the Ctr. Boost
button Ò on the front panel when
or fast reverse
››
Centre Boost is activated (see page
15).
o Wrap: Press these buttons to
increase or decrease the amount of
Wrap signal that is applied when the
unit is in any surround mode (see
page 16/17).
p Scan: Press this button to auto-
matically scan through the list of sta-
tions programmed into the tuner
memory. The tuner will stop for five
seconds at each station. To stop the
scan on a desired station press the
button again (see page 18).
q Calibrate: Press this button to
begin the calibration process that
establishes the proper output levels
for each channel (see page 13).
r Surround Mode: Press this but-
ton to select a surround processing
mode. Each press will cycle through
the list of available modes. Select
SURR OFF to turn all surround pro-
cessing off and listen in a two chan-
nel stereo mode (see page 16).
s Calibrate Speaker Select:
Press these buttons to select the
speaker being adjusted when using
the Calibrate function (see page 13).
t Calibrate Level Adjust: Press
these buttons to adjust the centre or
rear channel level when using the
Calibrate function (see page 14).
u RDS Seek: Press this button
until the RDS indicator lights to seek
only RDS stations or those of a
specific "PTY" or programme type.
Each press of the button will cycle
through the list of PTY types, but
beginning with ANY STN (any sta-
tion is seeked) and RDS ONLY,
where only RDS stations with any
PTY are seeked (see page 19).
Hide quick links:
Advertisement
Table of Contents
