Related Manuals for NEO 15301
Summary of Contents for NEO 15301
- Page 1 15301 Betmakers Bench Mount & Pedestal Kiosk (SST) USER SERVICE MANUAL 15301-ML002 REV01 ECN 5789...
- Page 2 Version History Dec. 2021 V 0.1 Release Version ISSUE NUMBER DATE COMMENTS APPROVED 01-12-2021 5789 INITIAL RELEASE L..DICKSON Page 2 15301-ML002 REV01 ECN 5789...
-
Page 3: Table Of Contents
6. Replacing the BNA Cash Box Module (Floor Pedestal) 7. Removing the BNA Bill Validation Module 8. Replacing the Power Supply 9. Replacing the Proximity Sensor 10. Replacing the NFC Reader 11. Replacing the LCD Screen Page 3 15301-ML002 REV01 ECN 5789... -
Page 4: Notices
Neo Products believes it is appropriate to do so. Changes will be incorporated in new editions of the publication and replaces all previous releases. -
Page 5: Safety Information
To avoid a shock hazard: • If Neo Products supplied a power cord, connect power to this unit only with the Neo Products provided power cord. Do not use the Neo Products provided power cord for any other product. •... -
Page 6: Caution Notices
Properly shielded and grounded cables and connectors must be used in order to meet emission limits. Neo Products is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. -
Page 7: Product Description
Power and Network connection for the Bench Mount & Floor Pedestal can be accessed by the following locations: Bench Mount—rear of unit: Bench Mount Ethernet connection Power on/off switch Floor Pedestal—rear of unit: Ethernet connection Power on/off switch Floor Pedestal Page 7 15301-ML002 REV01 ECN 5789... -
Page 8: Replacing The Printer Module
STEP 3 Remove the paper spindle & paper roll from the roller supports and un-feed from the Printer. STEP 4 Undo the Latch Swell to disengage the green Printer tray. Latch Swell. Page 8 15301-ML002 REV01 ECN 5789... - Page 9 Remove the plug (shown) from the USB Port & loom clips. The Printer Module can then be removed from the Kiosk. To re-install the replacement Printer Module, follow Steps 1 to 7 in reverse. Page 9 15301-ML002 REV01 ECN 5789...
-
Page 10: Replacing The Msr Module
STEP 2 Pull out the peripheral tray towards the operator. STEP 3 Remove the Betslip Tray. STEP 4 Undo the Latch Swell to disengage the green MSR Module. Latch Swell. Page 10 15301-ML002 REV01 ECN 5789... - Page 11 STEP 6 Unplug the power connector. STEP 7 Remove & retain 4x Pan Head Screws fastening the MSR Module from the MSR Tray. To re-install the replacement MSR Module, follow Steps 1 to 7 in reverse. Page 11 15301-ML002 REV01 ECN 5789...
-
Page 12: Replacing The Bna Cash Box Module (Bench Mount)
Bracket from the front pin nesting. STEP 4 Lift & pull the rear of the BNA Module out of the BNA enclosure, by guiding the BNA Module past the Latch Compression lock and BNA Enclosure flange. Page 12 15301-ML002 REV01 ECN 5789... - Page 13 Steps 1 to 5 in reverse. NOTE: Feed the BNA Module back into the BNA enclosure ensuring the loom and connectors to not interfere with fitment. Guide the loom & connectors to the LH side of the BNA enclosure. Page 13 15301-ML002 REV01 ECN 5789...
-
Page 14: Replacing The Bna Cash Box Module (Floor Pedestal)
& retaining 5x M4x8 Pan Head Screws fastening the BNA Mount Bracket to the base (4x) and vertical brace (1x). STEP 4 Before completely removing BNA Module, unplug the USB and Power Looms Power from the BNA Harness. Page 14 15301-ML002 REV01 ECN 5789... -
Page 15: Removing The Bna Bill Validation Module
& remove from the BNA Bracket. Guide the small tabs on the Module past the slots on the BNA Bracket. To re-install the replacement BNA Bill Validation, follow Steps 1 to 2 in reverse. Page 15 15301-ML002 REV01 ECN 5789... -
Page 16: Replacing The Power Supply
LCD Screen Door and Lower Door by unlocking the Lock at the Right-hand side of Pull out the Printer / MSR Module STEP 2 peripheral tray until it reaches stop. Remove Betslip Tray. STEP 3 Page 16 15301-ML002 REV01 ECN 5789... - Page 17 With two (2) hands, lift up the LH Side safety tab & push down the RH Side safety tab. LH Side Draw Slide RH Side Draw Slide Page 17 15301-ML002 REV01 ECN 5789...
- Page 18 Disconnect the 4x plugs from the STEP 9 Power Supply. Remove & retain 4x nuts fastening the Power Supply to the Base. To re-install the replacement Power Supply, follow Steps 1 to 9 in reverse. Page 18 15301-ML002 REV01 ECN 5789...
-
Page 19: Replacing The Proximity Sensor
Proximity Sensor plug from STEP 3 Remove the Printer Fascia. Remove & replace Proximity Sensor. To re-install the replacement Proximity Sensor, follow Steps 1 to 3 in reverse. The Proximity Sensor is glued into the Fascia replacement. Page 19 15301-ML002 REV01 ECN 5789... -
Page 20: Replacing The Nfc Reader
STEP 4 Use Side Cutter Pliers to remove the cable ties from the wiring loom back to the USB Port. Undo the Cable Tie Twist Locks (where applicable). To re-install the replacement NFC Reader, follow Steps 1 to 4 in reverse. Page 20 15301-ML002 REV01 ECN 5789... -
Page 21: Replacing The Lcd Screen
Left-hand side. Monitor Power STEP 3 Disconnect the HDMI from the NUC PC. STEP 4 Disconnect the white USB plug from White USB the NUC PC. (located behind the front USB plug). Page 21 15301-ML002 REV01 ECN 5789... - Page 22 Use a small flat screwdriver to unclip to securing tab on the Gas Strut. 7 Lift the LCD Screen from the 2x Hinge STEP Pins To re-install the replacement LCD Screen, follow Steps 1 to 7 in reverse. Page 22 15301-ML002 REV01 ECN 5789...
- Page 23 Page 23 15301-ML002 REV01 ECN 5789...