Advertisement
Quick Links
KT3 Kiosk
Quick Start Guide
Part# 06312-xxxx
Kiosk (06312-GA0xx)
Pedestal (06312-SPED001)
NeoProducts Pty Ltd ACN 007 152 374 ABN 76 007 152 374, 62-66 Pacific Drive, Keysborough, Vic, 3173
Telephone 03 9701 1511
www.neoproductsgroup.com
06312-ML002 Rev01_ECN 6535_KT3 QUICK START GUIDE
Page 1 of 12
Advertisement
Related Manuals for NEO KT3
Summary of Contents for NEO KT3
- Page 1 KT3 Kiosk Quick Start Guide Part# 06312-xxxx Kiosk (06312-GA0xx) Pedestal (06312-SPED001) NeoProducts Pty Ltd ACN 007 152 374 ABN 76 007 152 374, 62-66 Pacific Drive, Keysborough, Vic, 3173 Telephone 03 9701 1511 www.neoproductsgroup.com 06312-ML002 Rev01_ECN 6535_KT3 QUICK START GUIDE...
-
Page 2: Component Descriptions
KT3 Kiosk Component Descriptions BNA Door LCD Door Scanner Lifting Handle Printer Ticket Chute BNA Door Lock LCD Door Lock On/Off Switch Ethernet NeoProducts Pty Ltd ACN 007 152 374 ABN 76 007 152 374, 62-66 Pacific Drive, Keysborough, Vic, 3173 Telephone 03 9701 1511 www.neoproductsgroup.com... - Page 3 If the Kiosk is installed without the Pedestal, position into the final location & fasten accordingly. Push the Handles back into the storage position once complete. Then proceed to Step 4.0 “Power up the KT3 Kiosk”. 06312-ML002 Rev01_ECN 6535_KT3 QUICK START GUIDE Page 3 of 12...
- Page 4 Unpacking KT3 Pedestal (part# 06312-SPED001) ATTENTION: Prior to installation, refer to Chapter 1 – Safety Information in the KT3 User Service Manual. Remove the strapping from the carton. CAUTION: The strapping is under tension and can flick when cut.
- Page 5 CAUTION: Servicing of this product or unit is to QUICK START GUIDE be performed by trained service personnel only. Fit Kiosk to the Pedestal The Pedestal is provided with Weldnuts on the underside in the 3x locations highlighted. CAUTION: TWO (2) PERSON LIFT IS REQUIRED FOR THIS STEP.
- Page 6 CAUTION: Servicing of this product or unit is to QUICK START GUIDE be performed by trained service personnel only. Fit Kiosk to the Pedestal (continued) Step 1: Insert the Kiosk Lock Key into the bottom barrel lock to open the LCD Door in direction shown. Step 2: Insert the Kiosk Lock Key into the top barrel lock to open the BNA Door in direction shown.
- Page 7 CAUTION: Servicing of this product or unit is to QUICK START GUIDE be performed by trained service personnel only. Fit Kiosk to the Pedestal (continued) Partially pull the Printer Assembly in an outwards direction. The Printer Assembly Looms will need to be dis- connected from the Kiosk prior to full removal.
- Page 8 CAUTION: Servicing of this product or unit is to QUICK START GUIDE be performed by trained service personnel only. Power up the KT3 Kiosk Power, Fuse and Network are accessed from the rear of the Kiosk. The Kiosk is intended to be used in a location having...
- Page 9 CAUTION: Servicing of this product or unit is to QUICK START GUIDE be performed by trained service personnel only. Power up the KT3 Kiosk (continued) CAUTION - FOR SERVICE TEAM: The LCD power switch should remain in the on “I”...
- Page 10 CAUTION: Servicing of this product or unit is to QUICK START GUIDE be performed by trained service personnel only. Power up the KT3 Kiosk (continued) FOR SERVICE TEAM: A secondary Kiosk power switch is located on the inside of the Kiosk on the PSU Enclosure Assy in the location highlighted (LCD Screen removed for clarity).
-
Page 11: Loading Printer Paper
CAUTION: Servicing of this product or unit is to QUICK START GUIDE be performed by trained service personnel only. Loading Printer Paper The Printer is installed inside the Kiosk behind the LCD. On the right-hand side of the Kiosk, the barrel locks open the following Kiosk Doors. - Page 12 CAUTION: Servicing of this product or unit is to QUICK START GUIDE be performed by trained service personnel only. Loading Printer Paper (continued) Additional information regarding the Printer Paper is viewed on the Fan Plenum, located on the inside rear of the Kiosk in position shown.