Table of Contents
Advertisement
REVIEW INDIVIDUAL DAY, DAY GROUP, OR
COPIED ACTIVITIES
• Press PROG, then press the day key (SUN/1 through SAT/7) or
the day group key (wkDY/8, wkND/9 or ALL/0) to select the
day or day group to review.
NOTE: If you have entered data as a day group and attempt to
review any of the days individually, the message "End of Review"
will be displayed. This is because you must review data just as it
was entered, in this example, as a day group.
• Press REV, at which point the colon will disappear. Press REV
again to review the first programmed switch time. The associated
Switch On or Switch Off LED will be lit.
• Press REV again to review the next activity. If a switching time
includes a pulse or interval when you press REV, the length of
the pulse or interval will be displayed and the LED for Pulse or
INTVL will be lit. Continue to press REV until "End of
Review" is displayed. The display now prompts for a new day or
day group selection. Repeat the steps above for each circuit
individually.
• To automatically review a day or day group, press PROG, select
a day (SUN/1 thru SAT/7) or day group (wkDY/8, wkND/9 or
ALL/0), press REV, then press OK. If desired, press OK again to
pause auto review; press OK again to resume review, or press
REV to continue reviewing manually.
• If a day was copied from, you may review all days it was copied
to by selecting the copy from day, pressing OK, pressing COPY,
then pressing REV. For example, display might show 1 COPY
2 meaning that the day 1 schedule has been copied to day 2.
Push REV more times to review additional copy to days. If a day
is a copy, you may determine the day it was copied from by
selecting the day then pressing REV twice. A message will scroll
indicating the day it was copied from.
• Individual day review is not recommended for verifying
predicted operation of the timer because, since the actual
schedule is the composite of days, day groups, and copied days,
all of these would need to be reviewed, then manually combined,
to know the actual schedule for a given day. For example, if the
weekday (8) day group has scheduled activity, but no individual
weekdays (Monday thru Friday) have scheduled activity,
12
reviewing Monday only would immediately give the "End of
Review"message, indicating no activity, yet there will be activity
on Monday due to the weekday (8) day group schedule.
Therefore, always use the week long review feature for final
verification of the complete schedule.
NOTE: The effect of Holiday schedules cannot be seen during
week long review, so in addition to week long review, all Holidays
should also be reviewed to accurately predict the timer's operation.
REVIEW SPECIAL HOLIDAY SWITCHING
ACTIVITIES
To review special holiday switching activities, press PROG then
HLDY. Next enter the holiday reference number (01 to 99) for
the holiday activities you wish to review. Press OK, then press
REV, at which point the colon will disappear from the display.
Press REV again to display the first switching activity. Continue
to press REV while observing the LED prompts and program
times and/or Pulse and Interval times until "End of Review" is
displayed. Automatic review can also be used by pressing PROG,
HLDY, then entering the Holiday reference #, OK, REV, then
OK. If desired, use OK key to pause and resume auto review.
REVIEW INTERVAL OVERRIDE OPERATION
• Press PROG and do not select a day or day group.
• Press INTVL. The interval duration in days, hours and minutes
as programmed will be displayed.
• When reviewing data, the appropriate ENABLE switch must be
used, one switch at a time.
REVISE PROGRAM DATA
When revising program data, make note of the following:
• Run/Set switch must be in Set position
• Data is revised by causing it to be displayed during Review,
deleting it with the CLEAR key, and then replacing it with
new data, if desired.
• Program data may not be revised during week long review. You
must revise the data by reviewing the appropriate individual day,
day group, or "copied
from" day.
Next Generation
13
Hide quick links:
Advertisement
Table of Contents
