Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Fisher & Paykel DISHDRAWER DD60DTX6HI
Summary of Contents for Fisher & Paykel DISHDRAWER DD60DTX6HI
- Page 1 DOUBLE DISHDRAWER™ DISHWASHER INTEGRATED DD60DTX6HI INSTALLATION GUIDE...
-
Page 3: Safety And Warnings
SAFETY AND WARNINGS WARNING! WARNING! Electric Shock Hazard Electric Shock Hazard Failure to follow this advice may result in Failure to follow this advice may result in electrical shock or death. electrical shock or death. • Fitting an integrated panel requires access to •... - Page 4 SAFETY AND WARNINGS WARNING! To reduce the risk of fire, injury to persons or damage when using the appliance, follow the important safety instructions listed below. Read all the guidance before using the appliance. Servicing Do not repair or replace any part of the appliance unless specifically recommended in this guide.
-
Page 5: Tools And Components
TOOLS AND COMPONENTS PARTS SUPPLIED TOOLS REQUIRED Keep all packing materials until the unit has been inspected. Not supplied Inspect the product to ensure there is no shipping damage. If any damage is detected contact the dealer or retailer you bought the product from to report the damage. Fisher &... -
Page 6: Product Dimensions
PRODUCT DIMENSIONS PRODUCT DIMENSIONS A Overall height* 865 – 925 B Overall width** C Overall depth*** D Height of chassis E Depth of chassis F Ventilation gap between door panels PLAN ISOMETRIC G Depth of toe kick recess** Custom panel installation 40 – 100 Pre-finished panel installation 40 – 120 H Minimum clearance between toe kick panel... -
Page 7: Custom Panel Dimensions
CUSTOM PANEL DIMENSIONS Material specifications Maximum weight of drawer panels must not exceed 9kg (including handle) The panel should be adequately sealed to withstand moisture (50°C @ 80% RH). The back and sides of the panel should be completely sealed with a waterproof vapour barrier, such as polyurethane, to prevent damage. - Page 8 CABINETRY DIMENSIONS CLEARANCES Connections can be located in an adjacent cabinet on either side of the DishDrawer™ Dishwasher*** PLAN ISOMETRIC CABINETRY DIMENSIONS CABINETRY CLEARANCES A Minimum inside height* A Minimum clearance to adjacent cupboard door B Inside width B Minimum clearance to corner cupboard* *Access to both sides of the product will be required during installation.
- Page 9 PLUMBING & ELECTRICAL CONSIDERATIONS Hose and cord lengths Your services can be installed to either the left-hand or right-hand side of the product in an adjacent cabinet. Refer to 'Preparation' for service access requirements. If the drain hoses supplied are not long enough to reach your services, you may purchase a Fisher &...
-
Page 10: Service Access
PREPARATION SERVICE ACCESS MOISTURE PROTECTION We recommend locating the service holes on either side of the DishDrawer™ Dishwasher as shown below. If the holes are created through wood, ensure the edges are smooth and rounded Align the supplied moisture protection If the holes are created through metal, ensure the supplied edge protector is fitted. - Page 11 PUSH THE PRODUCT INTO THE CAVITY FIT CUSTOM DOOR PANELS If securing to cabinetry via method A Remove both side pins from each drawer Secure all four side brackets to the by twisting a quarter-turn towards the DishDrawer™ Dishwasher, aligning product front.
- Page 12 FIT THE CUSTOM PANEL Re-insert both side pins to each drawer Snap the bracket tab to remove. by pushing in and twisting a quarter-turn towards the rear of the product to secure panels into place. Attach the Knock-to-Pause module to the panels as shown.
- Page 13 SECURE TO CABINETRY VIA BRACKETS (METHOD A) SECURE TO CABINETRY VIA DRAWER REMOVAL (METHOD B) Open the lower drawer and press both locking tabs back to release. Partially open one of the drawers and remove the first screw cover from the trim moulding.
- Page 14 SECURE TO CABINETRY VIA DRAWER REMOVAL (METHOD B) INSTALL PRE-FINISHED TOE KICK Select your preferred pre-finished toe kick based on the depth of your desired toe kick recess. Toe kick depth of 40 – 56mm Toe kick depth of 56 – 120mm Flush pre-finished toe kick panel Recessed pre-finished toe kick panel Before refitting the drawer, ensure the hoses are not twisted.
- Page 15 INSTALL CUSTOM TOE KICK Align the custom panel to the recessed Re-align the custom panel to the pre-finished panel, referring to 'Custom recessed panel and secure using the panel dimensions' for guidance. provided screws. Mark a section of the recessed panel to Pre-drilling the screw bosses is be removed, ensuring it is shorter than recommended for optimal results.
- Page 16 PLUMBING & ELECTRICAL CONNECTION Ø38MM STANDPIPE INSTALLATION SINK TRAP/WASTE TEE INSTALLATION Install the drain hose support to the Install the drain hose support to the back wall, as close to the underside of back wall, as close to the underside of the countertop as possible.
-
Page 17: Installer Checklist
INSTALLER CHECKLIST TO BE COMPLETED BY THE INSTALLER Electrical … Ensure all electrical tests have been conducted in accordance with local regulations. Installation … Check all parts are installed correctly and are secure. Test operation … Ensure all clearance gaps have been maintained. …... -
Page 18: Troubleshooting
TROUBLESHOOTING No program indicator lights up when the drawer is opened DISPLAY POSSIBLE CAUSE WHAT TO DO Ensure power is connected and is switched on. Water 1 Ensure the water supply is turned on. may need to be activated. Refer to your user guide for details. AUTO POWER-ON Supply fault. - Page 20 FISHERPAYKEL.COM © Fisher & Paykel Appliances 2021. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue.