Hussmann IMPACT ED1 Installation Instructions Manual
Medium temperature, euro deli solid and glass front models joining instructions
Hide thumbs
Also See for IMPACT ED1:
- Technical data sheet (6 pages) ,
- Installation instructions manual (15 pages) ,
- Installation and operation manual (29 pages)
Advertisement
Quick Links
PARTS LIST
Item
Quantity
1.
1
2.
1
3.
1
4.
4
5.
4
6.
4
7.
4
8.
4
9.
1
10.
4
11.
4
12.
1
13.
1
14.
4
Note: Nut retainers are factory installed in the left end, and alignment pins are factory installed in the right end of each merchandiser.
NOTE: Be sure merchandisers have
been leveled according to the
installation instruction to assure good
fit and finish of the lineup. Locate
Joint Kit and check contents against
parts list. Be sure factory-installed nut
retainers and alignment pins are in
place.
Remove display racks, pans,
1
front shelf supports and front air
grilles from the right end as
shown.
2
Remove the rear panel(s) from
the right end. To remove a
panel, lift it up from the bottom
edge and out. No tools are
required.
Remove and discard shipping
braces and associated hardware.
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
®
Merchandisers
Description
Tape Gasket
Tape Gasket
Joining Plate
Screw #8 - 18 x
Cap Screw
Flat Washer
Lock Washer
Hex Nut 18 -
Joining Strap
Screw #10 - 32 x
Silicone Sealer
Joint Cover
Splashguard Joint Support
Cap Plug
Figure 1. Remove Shelf Supports and Air Grille
Medium Temperature, Euro Deli
Solid and Glass Front Models
Joining Instructions
1
1
/
x
/
x 120
2
2
1
5
/
x 1
/
x 180
2
8
1
/
2
5
1
/
- 18 x 1
/
16
4
5
/
16
5
/
16
5
/
16
3
/
Washer Head
8
Removable Front
Shelf Supports
ED1
IEDG1
EDS1
Removable
Return
Air Grilles
P/N 0406929
March, 2003
1
Advertisement
Related Manuals for Hussmann IMPACT ED1
Summary of Contents for Hussmann IMPACT ED1
-
Page 1: Joining Instructions
No tools are required. Remove and discard shipping braces and associated hardware. HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. ® Medium Temperature, Euro Deli Solid and Glass Front Models Description... - Page 2 • Gasket has high tack adhesive and must be properly placed the first time. Alignment Pins Figure 2. Verify Alignment Pins and Retainers Figure 3. Apply HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. ® Merchandisers Inch Gasket...
- Page 3 Medium Temperature, Euro Deli Solid Front Models Figure 4. Apply 1 Light Channel Figure 5. Install Joining Plate HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. Inch Gasket Extrusion P/N 0406929 Apply Gasket — 2 to cover foam-to-metal gap at the rear of the case and across the top as shown in Figure 4.
- Page 4 Flat Washers — 6, and Lock Washers — 7 to fasten merchandisers in the rear. Do not tighten fully. CASE CASE Figure 6. Join Front of Merchandisers DETAIL A Figure 7. Join Rear of Merchandisers HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. ® Merchandisers...
- Page 5 Medium Temperature, Euro Deli Solid Front Models Figure 8. Tighten Joints Wrapping Board Figure 9. Align and Join Wrapping Boards HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. Tighten joints in the order shown (A, B, C) until gaskets are compressed, and cases join smoothly.
- Page 6 Use #8 screws to fasten the hinge assembly. Drill 0.140 Dia. Pilot Hinge Holes (2 Places) Assembly Top Extrusion Parent Case Six Pre-Drilled Holes For Locating Hinge Assembly Figure 10. Fastening 90° Wedges HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. ® Merchandisers Wedge...
- Page 7 Holes (4 Places) Figure 11. Relocating Hinge Assembly Top Extrusion Parent Case Relocated Hinge Assembly Figure 12. Fastening 30°/45° Wedges HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. Wedge Drill 0.140 Dia. Pilot Holes (6 Places) Hinge Assembly Wedge Two Pre-Drilled Holes...
- Page 8 Apply silicone over each end of the joint cover. Place Cap Plug — 14 onto all exposed cap screws in the finished assembly. Joint Figure 13. Install Joint Cover DETAIL C Figure 14. Apply Cap Pug HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. ® Merchandisers...
- Page 9 Medium Temperature, Euro Deli Solid Front Models Figure 15. Apply Silicone to Support Bracket Figure 16. Install Splashguard Support HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. P/N 0406929 Use Silicone — 11 to fill any gaps between the front support brackets.