Multi-deck Frozen Food Joint Kit, making sure there is no breakage or damage. Be sure factory installed nut retainers are in place. See Figure 1. HUSSMANN CORPORATION, Bridgeton, MO 3044-2483 U.S.A. ® Joining Instructions Description “D” Gasket “D” Gasket, Mitered cut 42.8 inches Gasket 1 x 1 “e”...
Page 2
• Do not stretch gasket, especially around corners. • Remove paper backing before gasket is applied. See Figure 3 and Detail A. Figure 2. Removing Items from Case HUSSMANN CORPORATION, Bridgeton, MO 3044-2483 U.S.A. ® Merchandisers...
Page 3
A second 1 x inch gasket is installed under the “D” gasket on the plastic extrusion to add insulation to the plastic bottom and extru- sion. HUSSMANN CORPORATION, Bridgeton, MO 3044-2483 U.S.A. “D” shaped inch “e” shaped inch circle NOTE 3: Bottom “D”...
Page 4
Do not tighten fully. Use fasteners at locations A, B and C. Nut Retainer DETAIL C. Use fasteners at locations D, E, and F. DETAIL B Figure 4. Joining Cases HUSSMANN CORPORATION, Bridgeton, MO 3044-2483 U.S.A. ® Merchandisers FASTEN IN SEQUENCE SHOWN.
Page 5
See Figure 5 for more detail regarding this area of joining. Figure 5. Bolting Cases at the Baffle HUSSMANN CORPORATION, Bridgeton, MO 3044-2483 U.S.A. Next, fasten upper front and back of the case together at locations D, E and F using Cap Screw (Item) –...
Page 6
See Figure 8, Detail E. Tape Here Figure 6. Applying Butyl Tape Screws Splashguard Retainer DETAIL D 1st Case Figure 7. Installing Splashguard Brackets HUSSMANN CORPORATION, Bridgeton, MO 3044-2483 U.S.A. ® Merchandisers Splashguard Bracket 2nd Case Splashguard Brackets in proper position...
Page 7
P/N 0416185B Multi-deck Frozen Food Joining Instructions Joint Support DETAIL E Figure 8. Installing Splashguard Joint Support HUSSMANN CORPORATION, Bridgeton, MO 3044-2483 U.S.A.
Page 8
See Figure 9, Details F and G. Splashguard in place DETAIL G Figure 9. Installing Splashguard Splashguard Splashguard HUSSMANN CORPORATION, Bridgeton, MO 3044-2483 U.S.A. ® Merchandisers Splashguard Bracket DETAIL F...
Page 9
Multi-deck Frozen Food Joining Instructions Figure 10. Reinstalling Items from Step 1 HUSSMANN CORPORATION, Bridgeton, MO 3044-2483 U.S.A. P/N 0416185B Reinstall the items removed in Step 1. See Figure 10. The lineup can now be refrigerated and brought down to temperature.
Page 10
Start at the left end with the Internal Joint Trims and the 2-Foot Starter Bumper. Figure 11. Installing Internal Joint Trims 2-Foot Starter Bumper Lower Bumper 2-Foot Starter Bumper Figure 12. Installing Bumpers HUSSMANN CORPORATION, Bridgeton, MO 3044-2483 U.S.A. ® Merchandisers 2-Foot Starter Bumper Full Length Bumper Upper Bumper...
Page 11
Push Snap DETAIL H At the right end tap the top rails and bumpers to close any gaps. Figure 13. Installing Top Rails and Using Miter Box HUSSMANN CORPORATION, Bridgeton, MO 3044-2483 U.S.A. Full Length Top Rail Push Snap Push...