Related Manuals for Hussmann FMSS-L
Summary of Contents for Hussmann FMSS-L
- Page 1 FMSS-L Case-front self serviCe refrigerated MerChandiser P/n igss-fMss-l-0708 INSTALLATION & OPERATION GUIDE...
-
Page 2: Table Of Contents
Location ..................3 display when positioned in front of a “Parent” service case. Uncrating the Stand ..............3 The FMSS-L, FMSS-L-L only fits under Hussmann Chino Exterior Loading ................. 3 Style cases. Setting and Joining ..............3 Leveling .................. -
Page 3: Cut And Plan Views
(etc.) to create air setting and Joining currents around the merchandiser, as this will impair its The case that the FMSS-L connects to (the parent case) correct operation. through the rear of the case must be leveled and set prior to Product temperature should always be maintained at a installing the FMSS-L. -
Page 4: Joint Trim
FMSS-L. Remove clamps. 3. Set second case as close as possible to the first 9. Apply bead of silicone to top of bulkheads and slip case carefully guiding its electrical, refrigeration and on stainless steel bulkhead cap. -
Page 5: Bumper Installation Instructions
rev. 0708 installation (Cont'd) Bumper installation instructions Step : Use silicone lubricant to help the Step 1: Make sure the aluminum channel and end caps bumper slide into the channel. are installed. Step 3: Starting on one end: while inserting the bumper, Step 4: As you insert the bumper into the channel with push it up against the end cap to prevent one hand, pull the bumper toward you with... - Page 6 (Cont'd) Boston series 2000 NOTE: Flexible top: Over cut vinyl 1/8" for every 4' section for the flexible top to ensure a proper fit. note: rigid top: do not over cut. 1. Attach the base and end/corner cap to the desired surface by inserting #8 pan head screws through the pre-slotted holes in both the end cap and the base.
- Page 7 rev. 0708 installation (Cont'd) Boston 2000 eco series 1. Attach the base and end/corner cap to the desired surface by inserting #8 pan head screws through the pre-slotted holes in both the end cap and the base. Insert screws through the two holes of end cap and tighten. a.
- Page 8 (Cont'd) Boston 1000 series NOTE: Flexible top: Over cut vinyl 1/8" for every 4' section for the flexible top to ensure a proper fit. note: rigid top: do not over cut. installation 1. Attach the base and end/corner cap to the desired surface by inserting #8 pan head screws through the pre-slotted holes in both the end cap and the base.
-
Page 9: Plumbing
Defrost times underground with either common suction and liquid lines should be as directed in the FMSS-L technical data sheet. from the machine room or individual suction and liquid lines The number of defrosts per day should never change. -
Page 10: Thermostatic Expansion Valve Location
(Cont'd) thermostatic expansion valve location This device is located on the same side as the refrigeration stub. An Alco balanced port expansion valve model is furnished as standard equipment, unless otherwise specified by customer. expansion valve adjustment Expansion valves must be adjusted to fully feed the evaporator. -
Page 11: Electrical
Hussmann cases were not designed to “heat up” 6. There are vents located at the base of the front of the or “cool down” product - but rather to maintain an item’s glass, just above the front rail. -
Page 12: Important Steps
Cleaning always be used according to the manufacturer’s directions. Hussmann recommends using a clean damp chamois, or a It is essential to establish and regulate cleaning procedures. paper towel marketed as dust and abrasive free with 210 ®... -
Page 13: Maintenance
When cleaning your stainless steel products, take Copper Coils care to use non-abrasive tools. Soft Clothes and The copper coils used in Hussmann merchandisers may plastic scouring pads will NOT harm the steel’s be repaired in the field. Materials are available from local passive layer. -
Page 14: Electrical Wiring Diagrams
If you are not sure of the proper water treatment, call 8. regularly restore/Passivate stainless steel a treatment specialist. electrical Wiring diagrams W1400007 3’ W1400009 8’ W1400015 low / Medium temp 10’ W140001 11’ W1400016 1’ W1400017 fMss-l 4’ reM dUal teMP 4’ W1400005 fMss-l 8’ reM dUal teMP 8’... -
Page 15: Wiring Diagrams
rev. 0708 Wiring diagrams CAP UNUSED RED LEAD LH3-120-L FULHAM 125-01-3266 BALLAST... - Page 16 Wiring diagrams (Cont'd) LH3-120-L FULHAM 125-01-3266 BALLAST...
- Page 17 rev. 0708 Wiring diagrams (Cont'd) WIRE LH2-120-L FULHAM 125-01-3265 BALLAST WIRE LH2-120-L FULHAM 125-01-3265 BALLAST...
- Page 18 Wiring diagrams (Cont'd) LH4-120-L FULHAM 125-01-3267 BALLAST WIRE LH2-120-L FULHAM 125-01-3265 BALLAST...
- Page 19 rev. 0708 Wiring diagrams (Cont'd) 125-03-1129 F21T5-36" LH3-120-L FULHAM 125-01-3266 BALLAST 125-03-1129 F21T5-36" 125-03-1129 F21T5-36" LH3-120-L FULHAM 125-01-3266 BALLAST 125-03-1129 F21T5-36"...
- Page 20 Wiring diagrams (Cont'd) LH3-120-L FULHAM 125-01-3266 BALLAST...
- Page 21 rev. 0708 Wiring diagrams (Cont'd) LH3-120-L FULHAM 125-01-3266 BALLAST...
-
Page 22: Appendices
Public health will use the temperature of the product in installation instructions and recommendations determining if the refrigerator will be allowed to display provided by Hussmann for the installation potentially hazardous food. for the purpose of this of each individual type refrigerator. -
Page 23: Appendix D. - Recommendations To User
Fahrenheit shall be accurate to 1°C (1.8°F). 1. Are the shelf positions, number, and size Temperature measuring devices that are other than recommended by Hussmann? scaled only in Fahrenheit shall be accurate to 13. Is there an improper application or control °F. - Page 24 Food store refrigerators are not food chillers nor can they reclaim quality lost through previous mishandling. for further technical information, please log on to http://www.hussmann.com/products/fMss-l.htm...
-
Page 25: Service Record
_______________ __________________________________________________________________________________________________ _______________ __________________________________________________________________________________________________ _______________ __________________________________________________________________________________________________ _______________ __________________________________________________________________________________________________ _______________ __________________________________________________________________________________________________ _______________ __________________________________________________________________________________________________ _______________ __________________________________________________________________________________________________ /Chino The MODEL NAME and SERIAL NUMBER is required in order to provide you with the correct parts and information for your particular unit.