To ensure continued safety, do not re- move any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel. CAUTION—CLASS 1M INVISIBLE LASER RADIATION WHEN OPEN, DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS. AVIC-X940BT/XNUC...
Page 3
When Q1103 or Q1104 is shorted between their terminals, the laser diodes for DVD or CD will radiate beam. If the top cover is removed with no disc loaded while such short-circuit is continued, the naked eyes may be exposed to the laser beam. AVIC-X940BT/XNUC...
11.1 AV UNIT ............................... 250 11.2 KEYBOARD PCB ..........................254 11.3 DVD CORE UNIT ..........................256 11.4 IF PCB..............................258 11.5 MICRO SD PCB ........................... 262 11.6 CC MONITOR UNIT(SERVICE)......................264 11.7 LCD-IF UNIT ............................268 12. ELECTRICAL PARTS LIST ........................270 AVIC-X940BT/XNUC...
11. On this mechanism, Pickup and Spindle Motor can not be replaced at the service site, because a special facility is required for the adjustment after replacing them. So, if Pickup or Spindle Motor is defective, replace the Mechanism Unit. AVIC-X940BT/XNUC...
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. AVIC-X940BT/XNUC...
AVIC-X940BT ....6.1 inch wide/16:9 Rated power source....14.4 V DC Effective display area: (allowable voltage range: AVIC-X940BT ....136.2 mm × 72 mm 10.8 V to 15.1 V DC) Pixels ........... 384 000 (800 × 480) Grounding system....Negative type Display method ....... TFT Active matrix driving Maximum current consumption Backlight ........LED...
Page 8
H.264/MPEG4/WMV SD (AVIC-X940BT) microSD card, microSDHC card Fastening the detachable faceplate Compatible physical format • This description is for AVIC-X940BT.......... Version 2.00 If you do not plan to remove the detachable fa- File system....... FAT16, FAT32 Decoding format ....MP3/WMA/AAC/WAVE/ ceplate, the detachable faceplate can be fas- H.264/MPEG4/WMV...
Page 9
Sensitivity ......–140 dBm (typ) Equaliser (8-Band Graphic Equaliser): Position update frequency Frequency......40 Hz/80 Hz/200 Hz/400 Hz/ ......... Approx. once per second 1 kHz/2.5 kHz/8 kHz/10 kHz Gain ........±12 dB Loudness contour: Low ........+3.5 dB (100 Hz), +3 dB (10 kHz) AVIC-X940BT/XNUC...
Page 10
Ver.4.X, Ver.5.X, Ver.6.X : Dimensions (W × H × D) ... 68 mm × 49 mm × 19 mm .avi, .divx Weight .........180 g Note Specifications and design are subject to possible modifications without notice due to im- provements. AVIC-X940BT/XNUC...
Page 11
Tolerable temperature range: at sampling frequency Power on ......–10 °C to +60 °C 96 kHz) Power off ......–20 °C to +80 °C Signal-to-noise ratio....97 dB (1 kHz) (IEC-A net- work) (CD: 96 dB (1 kHz) (IEC-A network)) AVIC-X940BT/XNUC...
Page 12
Frequency response....30 Hz to 15 000 Hz (±3 dB) Stereo separation....45 dB (at 65 dBf, 1 kHz) MW tuner Frequency range..... 531 kHz to 1 602 kHz (9 kHz) Usable sensitivity....25 µV (S/N: 20 dB) Signal-to-noise ratio....62 dB (IEC-A network) AVIC-X940BT/XNUC...
Page 14
.m4a DivX decoding format....Home Theater Ver.3.11, Ver.4.X, Ver.5.X, Ver.6.X : .avi, .divx USB standard spec....USB 2.0 High Speed Max current supply ....1 A File system.........FAT16, FAT32 USB class........Mass storage class Decoding format ..... MP3/WMA/AAC/WAVE/ H.264/MPEG4/WMV AVIC-X940BT/XNUC...
Page 15
Parts supplied AVIC-X940BT/XNUC AVIC-F940BT/XNEU5, AVIC-F840BT/XNEU5 CDP1479 The navigation unit Power cord The navigation unit The navigation unit (AVIC-F940BT/XNEU5) (AVIC-F840BT/XNEU5) CDP1425 CXE3204 USB and mini-jack GPS antenna connector CDP1425 USB and mini-jack CXE2176 connector RDS-TMC tuner CDP1375 CPM1083 CDP1376 CDP1460 RCA connector...
2.2 DISC/CONTENT FORMAT The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Pioneer Corporation is under license. Other trademarks and trade names are those of their respective owners. AVIC-X940BT/XNUC...
Item to be checked regarding video Item to be checked regarding audio Block-noise Distortion Horizontal noise Noise Dot noise Volume too low Disturbed image (video jumpiness) Volume too high Too dark Volume fluctuating Too bright Sound interrupted Mottled color AVIC-X940BT/XNUC...
3.2 PCB LOCATIONS DVD Core Unit IF PCB CC Monitor Unit (Service) Keyboard PCB AV Unit LCD-IF Unit Micro SD PCB A:AVIC-X940BT/XNUC Unit Number : YWX5033 B:AVIC-F940BT/XNEU5 Unit Name : DVD Core Unit C:AVIC-F840BT/XNEU5 Unit Number : CXX4255(A) D:AVIC-F940BT/XNUW5 : CXX4256(B)
IF PCB <---> CC MONITOR UNIT 80P FPC Extension Cable GGD1633 AV UNIT <---> CC MONITOR UNIT Test Mode File GGS1109 Test Mode Grease List Name Jig No. Remarks Grease GEM1024 DVD Mechanism Module Grease GEM1038 DVD Mechanism Module Grease GEM1045 DVD Mechanism Module AVIC-X940BT/XNUC...
Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned Cleaning tools DVD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 Portions to be cleaned Cleaning tools Fans Cleaning paper : GED-008 AVIC-X940BT/XNUC...
C, F KEYBOARD SD CARD Connector CN4602 JA4712 JA151 CN5952 CODE MICRO SD PCB AV(PREOU IF UNIT Consists of A, E KEYBOARD PCB MICRO SD CARD B, D IF PCB CONNECTOR C, F : MICRO SD PCB CN5951 CXE3204 AVIC-X940BT/XNUC...
Page 23
JA1831 IP-BUS AV UNIT DVD CORE UNIT PS/IF SECTION SYSTEM uCOM SECTION AUDIO SECTION TUNER/VICS SECTION FLAP SENSOR IF JA2061 CN2201 CN2401 CN1851 AVIC-X940BT/XNUC AVIC-F940BT/XNEU5 AVIC-F840BT/XNEU5 CN101 RDS-TMC TUNER AVIC-F940BT/XNUW5 DRIVE UNIT CXE2176 AVIC-F940BT/XNAU only B, C AVIC-F840BT/XNAU CN291 CN251...
TO CC MONITOR UNIT(SERVICE) P1291 SOC 1A CEK1254-A TO IF PCB NKBUP TO IF PCB CCD5/CCD3 100mA P1201 LTC3850IGN SOC 3.15A CEK1259-A 5.21V : Max1.6A 3.43V : Max1.36A CCD5 1500mA FET(7A) TO CC MONITOR UNIT(SERVICE) CCD3 1360mA NAVION5 DDCLK2 (syscom) AVIC-X940BT/XNUC...
Page 39
Temp Sensor S-58LM20A-N4 3.0V(2.7V-5.5V) TYP:0.0045mA 225mA MAX:0.006mA 32mA TO IF PCB PKB Circuit LSA1576UB CCDIO3 TO CC MONITOR UNIT(SERVICE) NITOR AVIC-X940BT/XNUC...
Page 40
TYP 390mA VD5CONT DVD MECHANISM (syscom) MODULE VD8(Dry) MAX 840mA MT81V(D/D) TYP 200mA 8.1V BD9781HFP SOC 5A * 2.130A CEK1261-A VD8(Reg) MAX 140mA DDCLK TYP 130mA (syscom) DualZone MUTE RN4982 UC, AU Only POWER AMP TOSHIBA made IC "PA2030A" AVIC-X940BT/XNUC...
Is it OK? PICK UP Perform lens RF level check cleaned? cleaning Replace the Check2 CRG chassis Error rate check PICK UP Perform lens Is it OK? cleaned? cleaning Replace the CRG chassis Ckeck parts Finished other than PICK UP AVIC-X940BT/XNUC...
Page 50
10 - 65 (mA) DVDLD1 VCC5_PU Disc Check Point Threshold Remarks: LD current TCD-782 CDLD1 - VCC5_PU 150 - 900 (mV) 10 - 60 (mA) CDLD1 VCC5_PU Notes: Please pay attention to the laser diode damage by static electricity. AVIC-X940BT/XNUC...
Page 51
TCD-782 0000 0E00 ASMAX on display Check2 : Error rate check <Check> Status: [Tracking Closed] of TEST MODE Remarks Disc Check Point Threshold less than ID:40000 GGV1025 1.000E-3 less than GGV1025 ID:200000 1.000E-3 less than TCD-782 ID:HOME Position 2.500E-3 AVIC-X940BT/XNUC...
Page 53
<Check> Check the voltage at the “STANBY” test point while the power is on. Use the “DGND1” test point at the reference. Check point Module No. Specification value Unit STANBY - DGND1 VCC33 - 0.6 V or more V Side A GNDD1 STANBY Fig 1.1: STANBY check point AVIC-X940BT/XNUC...
Page 54
Check point Module No. Specification value Unit VDD5_1 - DGND1 5.0 ± 0.4 VCC33_1 - DGND1 3.3 ± 0.033 VCC12_1 - DGND1 1.2 ± 0.015 Side A VCC12 VCC33 VD5-1 DGND1 Fig 2.2: VDD5, VCC33, VCC12 voltage check points AVIC-X940BT/XNUC...
Page 55
<Check> Check the voltage at the “XRES” test point while the power is on. Use the “DGND1” test point at the reference. Check point Module No. Specification value Unit NRES - DGND1 VCC33 × 0.7 or more V Side A NRES DGND1 Fig 3.1: RESET check point AVIC-X940BT/XNUC...
Page 56
<Check> Check the voltage at the “VSENS” test point while the power is on. Use the “DGND1” test point at the reference. Check point Module No. Specification value Unit VSENS - DGND1 0.95 - 1.07 VD8 = 8.0 ± 0.4 V Side A VSENS DGND1 Fig 4.2: VSENS check point AVIC-X940BT/XNUC...
Page 57
Check point Module No. Specification value Unit 27 MHz ± 50 ppm IC1501 156pin - DGND1 Specification value Fig 5.2: Clock specification value Side A DGND1 IC1501 156pin Fig 5.3: 27 MHz check point AVIC-X940BT/XNUC...
Page 59
Side A Check point 1 (IC1480) Check point 2 (IC1501) Fig 6.2: SDRAM I/F check point AVIC-X940BT/XNUC...
Page 60
Check point Module No. Specification value Unit VD8_P - PGND1 8.0 ± 0.4 VD8_A - AGND1 8.0 ± 0.4 VCC5_1 - AGND1 5.0 ± 0.05 Side A AGND1 VCC5_1 PGND1 VD8_P VD8_A Fig 7.2: VD8, VCC5 voltage check points AVIC-X940BT/XNUC...
Page 61
Check with PGND_3 and GNDAU1 being the reference. Check point Module No. Specification value Unit VD8_A - PGND_3 8.0 ± 0.4 AVCC5 - GNDAU1 5.0 ± 0.05 Side A PGND3 GNDAU1 AVCC5 VD8_A Fig 8.2: VD8, AVCC5 voltage check points AVIC-X940BT/XNUC...
Page 62
2.0 V - VCC33V DGND - 0.8 V 33.8688 MHz ± 300 ppm Specification value 1 Specification Specification value 2 value 3 Fig 9.2: Clock specification value Side A DGND4 Check point 2 (IC1501 148 pin) Fig 9.3: DACCLK check point AVIC-X940BT/XNUC...
Page 63
VCC33V - 0.6 V or higher 0.4 V or lower Waveform 3 Specification value 2 Specification value 1 Fig 10.2: Serial 3 lines specification value Side A DGND1 151pin ADOUT signal 150pin LRCK signal 149pin SRCK signal Fig 10.3: Serial 3 lines check points AVIC-X940BT/XNUC...
Page 64
Reference waveform 1400 ± 150 mV Waveform 4 1400 ± 150 mV Waveform 4 Specification value is the root-mean-square value (rms). Fig 10.4: Analog audio out (LO, RO) specification value. Side A GNDAU3 Fig 10.5: Analog audio out check point AVIC-X940BT/XNUC...
Page 65
Specification value 2 Reference waveform VCC33V - 0.6 V or higher 0.4 V or lower Waveform 5 Specification value 2 Specification value 1 10.6: Digital audio signal (IECOUT) specification value Side A DGND1 Fig 10.7: Digital audio signal (IECOUT) check point AVIC-X940BT/XNUC...
Page 66
PEAK COMPOSITE signal Reference value Color burst Pedestal level BOTTOM Horizontal sync signal Fig 11.2: Waveform for the case of composite white 100% output Side A COMPOSITE GNDV2 Fig 11.3: VIDEO signal check point AVIC-X940BT/XNUC...
Page 67
(Refer to the LD power on time mode for the method of displaying the LD energizing time.) 2. If the second digit from the left of the energizing time display is showing E, such as “ E ”, it means that the flash memory has reached its life. Example: 0E000BB8 AVIC-X940BT/XNUC...
Page 68
Check point Module No. Specification value Unit 48 MHz ± 200 ppm IC1501 50pin - DGND1 Specification value Fig 13.2: Clock specification value Side A 48 MHz DGND1 Fig 13.3: 48 MHz check point AVIC-X940BT/XNUC...
Page 69
1. USB Memory: Play a song from USB memory and check D+ and D- with the DGND1 standards. 2. iPod: Connect iPod and check CP_RESET, SDATA and SCLOCK with the DGND1 standards until the Pioneer log appears. When iPod Touch or iPhone is connected, the logo is not displayed but only a check mark is displayed.
*11 Although it is USB source, it notifies as an error of DISC source. *12 Although it is USB source, iIt cancels only by Disc eject. *13 Although it is DISC source, it notifies as an error of USB source. *14 Although it is DISC source, It cancels only without Device. AVIC-X940BT/XNUC...
Page 73
Cause Action (Reference) Change the destination. Route calculation was not Route calculation has failed be- Consult the Pioneer Local dealer if this mes- possible. cause of a malfunction in map data, software, or hardware. sage persists. Route calculation not possi- The destination is too far.
Page 74
The iPod is not compatible with this Use an iPod of a compatible version. not connected. navigation system. Disconnect the cable from iPod. Once iPod Communication failure main menu is displayed, connect the cable again. If the message appears frequently, consult your dealer. AVIC-X940BT/XNUC...
2. How to Start-up Test Mode Start-up by SD card. 1. Download GGS1109 from the Service Site. 2. Decompress the file. 3. Copy the decompressed file to the SD card root. 4. Insert the SD card to the product and turn ACC on. AVIC-X940BT/XNUC...
Page 77
Test of Hard Key. Key Test Status display of Input Port. Port Test Status display/changeover of Output Port. Display drive information, disc scanning Drive Maintenance (verification of volume). File operation and file deletion. File Maintenance Dumping display of file contents. AVIC-X940BT/XNUC...
Page 78
Data readout of NAND FLASH. NAND Test Writing data or file into NAND FLASH. Execution of User Area clearing. USER'S AREA OF FLASH CLEAR Guiding Audio Line confirmation by the replay of Audio Play Test audio file. Display various test images. Image Test AVIC-X940BT/XNUC...
Page 79
Display image of back camera on navigation screen. BACK CAMERA TEST Check wire connecting status of 3 color signals RGB KEY ILLMINATION TEST for RGB key illumination. Confirming flap close and displaying RPS value. MechaClose Position Confirmation Display product information. PRODUCT INFORMATION AVIC-X940BT/XNUC...
Page 80
Version of HD-Radio F/W [ *.****** ]: Value of Version VERSION [NO_SET]: No information NO_SET except AVIC-Z140BH/XNUC NAND CID Firmware ID of NAND Flash [ *.****** ]: ID value [ GET_NG ]: Acquisition failed 2. Model Information [The second page] AVIC-X940BT/XNUC...
Page 81
Item Item Contents Information Display PRODUCT NUMBER Product Model Number AVIC-Z140BH/XNUC : North America AVIC-X940BT/XNUC : North America AVIC-F40BT/XNEU5 : Europe AVIC-F940BT/XNEU5 : Europe AVIC-F840BT/XNEU5 : Europe AVIC-F40BT/XNAU : Australia AVIC-F940BT/XNAU : Australia AVIC-F840BT/XNAU : Australia AVIC-F940BT/XNUW5 : Russia NO_SET...
Page 82
Error Info 1, 2 : Additional Information Version Info : Program version Versions for boot loader, platform and application are displayed. File : Display file name where error happened. : Log information (The content is displayed only when saved) AVIC-X940BT/XNUC...
Page 83
<< Selection Screen>> The history is saved in the following folder configuration; SD or USB Memory error.txt <- Error History log.txt <- Log History AstLog <- Exception History Folder DBMSG000.log SYSER000.log EMERG000.log EMERG001.log (Histories may be saved up to EMERG511.log) AVIC-X940BT/XNUC...
Page 84
5. Bluetooth Firmware Write . . . Firmware of Bluetooth chip is written. * Normal writing becomes unable if power is off during the writing. On this occasion, please retry firmware writing. 6. Opening Data Write . . . Startup screen data is written. AVIC-X940BT/XNUC...
Page 85
Less than 1 second Connected !!ERROR!! 6 Bluetooth Unit Confirm communication Approx. 60 seconds, Connected !!ERROR!! setup status max. 7 HD-Radio Confirm connection status Less than 1 second Connected !!ERROR!! * HD-Radio always makes an error in models except AVIC-Z140BH/XNUC. AVIC-X940BT/XNUC...
Page 86
At the calibration test, calibration adjustment is performed to compensate the misalignment of the touch panel. User touches displayed 17 points in order and correction is automatically performed after touching. At the User Calibration Confirmation, it is displayed that whether the user has executed calibration adjustment or not. AVIC-X940BT/XNUC...
Page 87
[FINISHED] is displayed and if the calibration is unsuccessful, [NG] is displayed. Return to main menu with [HOME] key. Key operation Key assignment Return to Main Menu HOME 3. User Calibration Confirmation The following is displayed when User already performed calibration FINISHED User not performed yet calibration NOT FINISHED AVIC-X940BT/XNUC...
Page 88
CheckSum Display the checksum of adjustment item group displayed on screen in hexadecimal. In the case of group which does not have checksum, the value is indicated as ------. Source Display the source name of image indicated as background. AVIC-X940BT/XNUC...
Page 89
Display the factory shipping out reference value of COM_DC value in hexadecimal. This is just the item for indication and not adjustable. 3. Backlight Test <<Items>> Contents Item Name Backlight Brightness Data Current backlight brightness (microcomputer saved value). Backlight Brightness Chg Backlight brightness is adjustable by the set value. AVIC-X940BT/XNUC...
Page 90
E2PROM Write ON/OFF setting of writing to E2PROM 5. E2PROM Initialize [Range Selection Screen] <<Items>> Item Contents Item All Initialize Perform initialization of E2PROM entire region. Part Initialize Perform initialization of E2PROM specified region (Region assigned by the Design Division). AVIC-X940BT/XNUC...
Page 91
0x00020001 DISC EJECT MODE 0x00020013 NAVI/AV VOL UP 0x00020008 VOL UP VOL DOWN 0x00020009 VOL DOWN LEFT 0x00020006 LEFT RIGHT 0x00020007 RIGHT VOICE UI 0x0002001a VOICE RECOGNITION HOME+LEFT 0x0002001b MENU+LEFT HOME+RIGHT 0x0002001c MENU+RIGHT LEFT+MODE 0x0002001d LEFT+NAVI/AV EJECT+MODE 0x0002001e EJECT+NAVI/AV AVIC-X940BT/XNUC...
Page 92
Low: Not detected. (Normal Operation) 5. High side SW Overcurrent Detection Signal Input for USB Overcurrent Protection: At this port, status is displayed as the detection of short-circuit of power supply for iPod (USB). Hi: Normal operation Low: Short-circuit detected AVIC-X940BT/XNUC...
Page 93
Boot sector incorrect 2000570d Not supported drive 2000570e Drive information failed to be obtained 2000570f No consecutive vacant region exists 20005710 Device connection failed to be released 20005711 Device connection start failed 20005712 Synchronous object generation failed 20005713 Incorrect parameters AVIC-X940BT/XNUC...
Page 94
Scan Disc Screen for Executed Result of Scan Disc In the case of total error number being zero after the execution of scan disc, “There isn’t error on the volume” is displayed. AVIC-X940BT/XNUC...
Page 95
Time of Update (Only at the time of file) At the time of File: Extension Indication Displaying File Attribute (Only at the time of file) W : Writing Approval Attribute R : Writing Prohibition Attribute H : Hidden Attribute A : Archive Attribute S : System Attribute AVIC-X940BT/XNUC...
Page 96
Altitude Accuracy for VDOP GPS Time Latitude Velocity in Horizontal Direction Longitude Azimuth of Velocity in Horizontal Direction Altitude Velocity in Vertical Direction Long Axis of Error Ellipsoid Short Axis of Error Ellipsoid Long Axis Inclination of Error Ellipsoid AVIC-X940BT/XNUC...
Page 97
Received Signal Level Positioning Status Accuracy * The Third Page [Diag] Channel : GPS Diagnostic Result Antenna Shot : Detection of Antenna Short Circuit Antenna Open : Detection of Antenna Open Circuit Backup Error : Detection of Backup Error AVIC-X940BT/XNUC...
Page 98
* The Fourth Page [Err Info] Count Error Number Week of Error Time of Error Happened Day of the Week Happened 13. GPS ASSESSMENTT Version information for GPS driver and sensor module are displayed on the screen. AVIC-X940BT/XNUC...
Page 99
[At the time when the clearing of learning degree in Gyro Sensor is successful] [At the time when the clearing of learning degree in Gyro Sensor is unsuccessful] If the clearing of learning level in gyro sensor results in failure, "ERROR!" is displayed. AVIC-X940BT/XNUC...
Page 100
Vehicle speed pulse distance Display Content of LOW SPEED DISTANCE Status of SPEED PULSE Display SPEED PULSE Low speed vehicle speed pulse under learning CHECK Low speed vehicle speed pulse, OK Low speed vehicle speed pulse, NG Others ----- AVIC-X940BT/XNUC...
Page 101
This screen is also displayed when Bluetooth is internally used in other test. Please execute Bluetooth Unit test again after depressing [HOME] key or resetting. 0. Sub Menu Screen Select item with [ ], [ ] keys and determine with [MODE] key. Return to the main menu with [HOME] key. AVIC-X940BT/XNUC...
Page 102
[MODE] key, and then select a pattern. Select a page with [ ], [ ] keys. Select an item with [ ], [ ] keys. Emit the radio wave of pattern selected with [MODE] key. Return to the sub menu with [HOME] key. AVIC-X940BT/XNUC...
Page 103
40_10 41_10 42_10 43_10 44_10 Page 5 36_11. Using Only 20 Mid Channel (31-50) 37_11 38_11 39_11 40_11 41_11 42_11 43_11 44_11 Page 6 36_12. Using Only 20 High Channel (60-79) 37_12 38_12 39_12 40_12 41_12 42_12 43_12 44_12 AVIC-X940BT/XNUC...
Page 104
] keys and determine with [MODE] key. Return to the sub menu with [HOME] key. Flow of Process After the detailed setting which was performed on [1. Parameter Setting], select [2. Execute] and emit the radio wave which was set by depressing [HOME] key. AVIC-X940BT/XNUC...
Page 105
Setting screen for the selected item is displayed. Select item desired to be changed with [ ], [ ] keys. Value is set with [MODE] key and return to Output Frequency Channel Extended Test menu. Return to Output Frequency Channel Extended Test menu with [HOME] key. AVIC-X940BT/XNUC...
Page 106
Return to Output Frequency Channel Extended Test menu with [HOME] key. In Case of Error Exists in the Setting Value Value is set with [MODE] key and return to Output Frequency Channel Extended Test menu. Please retry by entering correct value. AVIC-X940BT/XNUC...
Page 107
(002-254) Value in parenthesis is able to be set arbitrarily 6. Scrambler Mode 0. OFF 1. ON 7. Power Level 0. Power Level 0 1. Power Level 1 2. Power Level 2 3. Power Level 3 4. Power Level 4 AVIC-X940BT/XNUC...
Page 108
Fail to get device informations. In the Case of Internal Buffer Generation not Successful Fail to create internal buffer. In the Case of Writing a File not Successful File write error. In the Case of Verify not Successful Fail to verify data. AVIC-X940BT/XNUC...
Page 109
NAND-FLASH anymore. CRC Error, This is displayed when data writing/reading is failed. Uncorrectable Error Device under This is displayed when NAND-FLASH is under preparation Preparation (such as under mounting) and unusable. Other Errors Displayed when errors are other than above. AVIC-X940BT/XNUC...
Page 110
This happens when play targeted file is not found. Device open failed. This happens when software setting for play is unsuccessful. Fail to create internal buffer. Securing memory required for play is unsuccessful. Device Error. Problem happens in software processing during audio playing. AVIC-X940BT/XNUC...
Page 111
A Jpeg image for test in a directory in a predefined navigation is displayed. If an image file with a name "Natural.jpg" is placed on the route or USB or SD, image files other than default image can be displayed. AVIC-X940BT/XNUC...
Page 112
LCD Temperature Sensor 3F6 [- 25°C] ~ 015B [85°C] : Normal Operation Range (determination is not displayed) Other than above: NG NAVI Temperature Sensor 6 ~ 61 [°C] : Normal Operation Range (determination is not displayed) Other than above: NG AVIC-X940BT/XNUC...
Page 114
The confirmation of muting circuit on the guidance audio line is also confirmed by this test. <<Screen Description>> GMUTE : Mute setting on guidance audio line. During “L” setting, microphone input is output from the front speaker. During “H” setting, muting status is set. AVIC-X940BT/XNUC...
Page 115
Possible hardware failure exists. Failed to mute off. Mute releasing of AV source is unsuccessful. Possible hardware failure exists. Device Open Error. Software setting for playing sinusoidal wave is unsuccessful. Device Error. Problem happens in software processing during audio playing. AVIC-X940BT/XNUC...
Page 116
Possible hardware failure exists. Failed to mute off. Mute releasing of AV source is unsuccessful. Possible hardware failure exists. Device Open Error. Software setting for playing sinusoidal wave is unsuccessful. Device Error. Problem happens in software processing during audio playing. AVIC-X940BT/XNUC...
Page 117
POWER CONTROL NG This is displayed when fan power source control is unsuccessful. STOP<=>FAST POWER CONTROL NG This is displayed when fan power source control is unsuccessful. SLOW<=>FAST SPEED CONTROL NG This is displayed when fan speed control is unsuccessful. AVIC-X940BT/XNUC...
Page 118
Manufacturer code of connected wired remote control is displayed on the screen. 0. Wired Remote Control Test Menu This is the menu screen for selecting items which configure this test. 1.1. Remote Control Key Code Obtainment (Key Code not obtained) This is the case of key code not obtained. AVIC-X940BT/XNUC...
Page 119
VOL UP 0x00010008 VOL DOWN 0x00010009 BAND 0x0001000A PHONE 0x0001000B ON HOOK 0x0001000C OFF HOOK 0x0001000D SAT TEXT 0x0001000E Audio Recognition 0x0001001A 2.1. Manufacturer Code Input Information (Under Obtainment) Obtain the manufacturer code for the connected wired remote control. AVIC-X940BT/XNUC...
Page 120
* Manufacturer Code is obtainable only for Japanese Domestic model. Value of [FF] is displayed this model. 2.3. Manufacturer Code Input Information (Obtainment Failed) If the obtained code is abnormal value, this becomes NG and the screen below is displayed. AVIC-X940BT/XNUC...
Page 121
When the setting of simulation time is successful, the screen becomes as follows. In addition, current time is set under the condition of the GPS antenna connected. If the time is counted at this time, the function of RTC is normal. AVIC-X940BT/XNUC...
Page 122
Securing the memory for data comparison was unsuccessful. Data write error Data writing was unsuccessful. File seek error File pointer operation was unsuccessful. Data read error Reading out of data was unsuccessful. Data verify error Data comparison was unsuccessful. AVIC-X940BT/XNUC...
Page 123
Securing the memory for data comparison was unsuccessful. Data write error Data writing was unsuccessful. Data seek error File pointer operation was unsuccessful. Data read error Reading out of data was unsuccessful. Data verify error Data comparison was unsuccessful. AVIC-X940BT/XNUC...
Page 124
Statuses of all terminals are inspected and the results are displayed. When all terminals are opened, the screen becomes blue. The terminal to be inspected varies depending on the place of destination. Place of destination Inspection terminal RDS/TMC RDS/TMC CAN-BUS RDS/TMC AVIC-X940BT/XNUC...
Page 125
Statuses of all terminals are inspected and the results are displayed. When all terminals are short-circuited, the screen becomes blue. The terminal to be inspected varies depending on the place of destination. Place of destination Inspection terminal RDS/TMC RDS/TMC CAN-BUS RDS/TMC AVIC-X940BT/XNUC...
Page 126
Case 2. Failed to Change Source of iIPod/AUX. Source switchover for microcomputer was unsuccessful. Case 3. Failed to Setup iPod/AUX-OFF. Input OFF setting for microcomputer was unsuccessful. Case 4. Failed to Attest iPod. iPod authentication was unsuccessful at the start of test. AVIC-X940BT/XNUC...
Page 127
Case 1. Failed to Setup VTR-ON. Input ON setting for microcomputer was unsuccessful. Case 2. Failed to Change Source of VTR. Source switchover for microcomputer was unsuccessful. Case 3. Failed to Setup VTR-OFF. Input OFF setting for microcomputer was unsuccessful. AVIC-X940BT/XNUC...
Page 128
In the case microcomputer communication was unsuccessful. 2. Display Directly This is the screen when back camera image is under displa The following error message is displayed when error happens; Case. Failed to Setup BackCamera. In the case microcomputer communication was unsuccessful. AVIC-X940BT/XNUC...
Page 129
If the RPS value obtained at close status corresponds to 0x06h - 0x36h Then the test is OK. In other cases, the test is NG. The testing fails in models not equipped with a drive mecha. Test Screen When Test is OK AVIC-X940BT/XNUC...
Page 130
The error always occurs in models other than the following: AVIC-Z140BH/XNUC AVIC-F40BT/XNEU5 AVIC-F40BT/XNAU 37. PRODUCT INFORMATION The product information allocated to the product is displayed on the screen. 16 digit values sectioned into four (4) separated by a dot are displayed on the screen. Example: 0000.1111.2222.3333 AVIC-X940BT/XNUC...
3 long. The test mode is released by ACC-OFF operation. Slave Test Mode DVD REGION DISP In order to enter the DVD mechanism module test mode, select "Slave Test Mode". DVD DEBUG DISP DVD TOUCH DIRECT AVIC-X940BT/XNUC...
Page 132
01 : TEST KEY (1) 02 : TEST KEY (2) 03 : TEST KEY (3) 04 : TEST KEY (4) 05 : TEST KEY (5) 06 : TEST KEY (6) 07 : TEST KEY (7) 08 : TEST KEY (8) AVIC-X940BT/XNUC...
Page 133
3C00 0000 : CRG- Tracking close state FBAL coefficient (layer 0) FBAL coefficient (layer 1) Focus gain coefficient (layer 0) Focus gain coefficient (layer 1) Tracking gain coefficient (layer 0) Tracking gain coefficient (layer 1) AS normalization adjustment value (layer 0) AVIC-X940BT/XNUC...
Page 134
Designation of digit by command (1) and (2). UP/DOWN of numbers by command (3) and (4). Fix by command (5). Power_OFF Error occurrence at Power_OFF [Note] If an error occurs at Power_OFF, reset cannot be made. In such a case, it is necessary to turn the power off and start the test mode once again. Error display AVIC-X940BT/XNUC...
Page 135
[Note] If the power on time is 999999 hours or more, it is always reported as 999999 hours. [Note] If the power on time is “*E** ****”, the value may not be correct due to the life of the flash memory. AVIC-X940BT/XNUC...
Page 136
5: Return CRG moves to the most outer Please Input Number Now Running Please Input Number <Error> ERROR 1: Power OFF select Code : 00000000 Please Input Number <Error : Power OFF> ERROR Code : 00000000 Please Reset AVIC-X940BT/XNUC...
Disconnect the Cord Assy using GGF1539 (See Fig.4). Remove the four screws and then remove CC Monitor Unit (Service) Attention at assembly: A lever of the connector is small. Lock it surely. Attention at assembly: Pay attention to the direction of FFC. Fig.3 AVIC-X940BT/XNUC...
Page 138
Release the ten latches and then remove the Holder (2). (Fig.5) Fig.5 Holder (3) Remove the two screws and then remove the Holder (3). (Fig.6) Remove the two screws and then remove the Keyboard PCB. (Fig.6) Do not push or wimple FFC. Keyboard PCB Fig.6 AVIC-X940BT/XNUC...
Page 139
Don’t remove this screws excluding the dismantlement of the DVD Mechanism Module. (Fig.8) Fig.8 - Removing the Heat Sink (Fig.9) Heat Sink Remove the six screws. Remove the two screws. Disconnect the connector and then remove the Heat Sink. Fig.9 AVIC-X940BT/XNUC...
Page 140
IF Unit. (Fig.12) Fig.11 Fig.12 Attention at assembly) When you assemble the IF Unit Holder and the Bracket, the Claw enters the hole. They are hardly separated, so pay attention to the deformation. The IF PCB Holder should contact the Bracket. AVIC-X940BT/XNUC...
Page 141
While pushing the Switch pull out the FFC as shown. While pushing the Switch remove the FFC. Switch Fig.13 - Removing the AV Unit (Fig.14) Remove the screw. Remove the five screws and then remove the AV Unit. AV Unit Fig.14 AVIC-X940BT/XNUC...
Press the EJECT key only after the disk has stopped completely. If the product hangs up turn the power OFF immediately. Don't touch the volume for laser power adjustment other than the time of POWER adjustment. (Laser diode may be damaged.) AVIC-X940BT/XNUC...
Page 143
Adjustment screwdriver : crosshead, No.0, nonmetal (ceramic screwdriver for adjustment) Line Locating The following line locating is required. Power adjustment Power adjustment VREF1 Connection Diagram : Checking terminal for oscilloscope The figure in parentheses of resistor / capacitor is constant. Universal board VREF1 Enlarged For CDt For DVDt AVIC-X940BT/XNUC...
Page 144
Adjust VR in order that this width is within the range of target FR level adjustment value. Power adjustment standard RF level adjustment value (The setup is completed. STEP 12, 26) 848 mV to 892 mV 658 mV to 702 mV AVIC-X940BT/XNUC...
Page 145
16. Return the state of mecha to clockwise. 17. Set up again (state of mecha to clockwise / setting of DVD single layer) and conduct the final check of RF level and ERR rate. (Check in the state of Tracking Close) 18. Eject. AVIC-X940BT/XNUC...
Page 146
(Check in the state of Tracking Close) 528 mV to 832 mV Refer to FE test mode function flow. 1.0E – 2 and under 32. Eject. Refer to FE test mode function flow. 33. Take out CD TCD-782 (or TCD-792). 34. Power off. AVIC-X940BT/XNUC...
Page 149
21-16 Quick Start Guide See Contrast table (2) Sheet See Contrast table (2) GPS Antenna Assy CXE3204 (2) CONTRAST TABLE AVIC-X940BT/XNUC, AVIC-F940BT/XNEU5, AVIC-F840BT/XNEU5, AVIC-F940BT/XNUW5, AVIC-F940BT/ XNAU and AVIC-F840BT/XNAU are constructed the same except for the following: AVIC-X940BT/ AVIC-F940BT/ AVIC-F840BT/ AVIC-F940BT/ AVIC-F940BT/...
Page 150
CRD4633 English(Great Britain), French, Italian, Spanish(Espanol), German, Dutch CRB3859 English(Great Britain) CRB3860 Russian CRB3863 English(Great Britain) CRB3864 English(Great Britain) CRB3865 English CRB3866 French CRB3867 English(Great Britain) CRB3868 French CRB3869 Italian CRB3870 Spanish(Espanol) CRB3871 German CRB3872 Dutch CRB3873 English(Great Britain) AVIC-X940BT/XNUC...
Page 151
* CRB3848 Spanish(Espanol) * CRB3849 German * CRB3850 Dutch * CRB3857 English(Great Britain) * CRB3858 Russian All operation manuals are supplied in PDF files by the CD-ROM. Regarding the availability of paper manual, contact Pioneer Service representative in your region. AVIC-X940BT/XNUC...
Page 153
See Contrast table (2) Holder See Contrast table (2) See Contrast table (2) Holder See Contrast table (2) (2) CONTRAST TABLE AVIC-X940BT/XNUC, AVIC-F940BT/XNEU5, AVIC-F840BT/XNEU5, AVIC-F940BT/XNUW5, AVIC-F940BT/ XNAU and AVIC-F840BT/XNAU are constructed the same except for the following: AVIC-X940BT/ AVIC-F940BT/ AVIC-F840BT/ AVIC-F940BT/ AVIC-F940BT/...
Page 155
CC Monitor Unit (Service) See Contrast table (2) TFT LCD Assy CXE5253 Cord Assy CDE9389 (2) CONTRAST TABLE AVIC-X940BT/XNUC, AVIC-F940BT/XNEU5, AVIC-F840BT/XNEU5, AVIC-F940BT/XNUW5, AVIC-F940BT/ XNAU and AVIC-F840BT/XNAU are constructed the same except for the following: AVIC-X940BT/ AVIC-F940BT/ AVIC-F840BT/ AVIC-F940BT/ AVIC-F940BT/ Mark...
Page 193
KEYBOARD PCB R3031 R3044 R3037 R3043 3.6k 1.2k 2.4k 6.8k MULTI CONTROL S3003 CSD1168-A GNDD T ANTENNA JA2901 IF UNIT Consists of KEYBOARD PCB CTX1110-A IF PCB MICRO SD PCB AVIC-X940BT/XNUC...
Page 195
LECRGM WHITE SPDLP LECRGM R1111 R1116 SPDLM CRG(L/E) MOTOR Q1103 KTA1664(Y) LECRGP GREEN LECRGP DVDLDO LPCO1 Q1101 2SC4081(QRS) SPDLM SPDLM SPINDLE MOTOR GNDA4 C1106 SPDLP SPDLP 0.01u/16 GNDP GNDA : The power supply is shown with the marked box. AVIC-X940BT/XNUC...
1.8V (GND) GNDD TCXO C151 OUTPUT 0.01u/16 GNDD GNDD GNDD GNDD GNDD GNDD GNDD L157 R173 L158 CTF1736-A AVIC-X940BT/XNUC Application list R401 23mm AVIC-F940BT/XNEU5 R402 GNDD R403 R404 AVIC-F840BT/XNEU5 GNDD only A R405 GNDD GNDD GNDD only B R406 GNDD...
Page 201
CTOVICS R257 1k VICSTOC Application list VICSTOC (2125) R401 IC251 R402 TC7WH126FK IF UNIT R403 R404 Consists of GNDD GNDD only A R405 KEYBOARD PCB only B R406 IF PCB only D R407 only E R408 MICRO SD PCB AVIC-X940BT/XNUC...
The expression of the unit in this manual is shown by u instead of . Please do not make a mistake. Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. : CXX4258(E) A:AVIC-X940BT/XNUC : CXX4260(F) B:AVIC-F940BT/XNEU5 Unit Name : CC Monitor Unit(Service) C:AVIC-F840BT/XNEU5...
Page 271
IMSA-6803-01Y900 D 1141 (B,111,141) Diode KDS160 P 2441 (A,165,25) Poly Switch FSMD050-R D 1151 (B,54,127) Diode UDZS6R8(B) D 1202 (B,158,41) Diode RB160M-40 GY2221 (A,99,20) Sensor CSX1147 D 1203 (B,158,51) Diode RB160M-40 CN1521 (A,33,7) Connector VKN1620 CN1851 (A,74,66) Connector(A,B,D,E) VKN1610 AVIC-X940BT/XNUC...
Page 272
(B,108,48) RS1/16SS473J R 1211 (B,147,37) RS1/16SS100J R 1357 (A,117,51) (A,D) RS1/16SS472J R 1212 (B,148,52) RS1/16SS100J R 1213 (B,148,37) RS1/16SS100J R 1358 (A,117,49) RS1/16SS472J R 1214 (B,150,51) RS1/16SS104J R 1359 (B,113,60) RS1/16SS473J R 1215 (B,149,34) RS1/16SS0R0J R 1360 (A,116,46) RS1/16SS104J AVIC-X940BT/XNUC...
Page 273
(A,78,48) (A,B,C,E,F) RS1/16SS0R0J R 1515 (B,87,63) RS1/16SS104J R 1429 (B,111,46) RS1/16SS0R0J R 1516 (B,89,63) RS1/16SS104J R 1430 (A,109,60) RS1/16SS221J R 1517 (B,89,60) RS1/16SS104J R 1431 (A,82,56) RS1/16SS681J R 1518 (B,85,60) RS1/16SS224J R 1432 (A,80,57) RS1/16SS681J R 1519 (B,79,67) RS1/16SS0R0J AVIC-X940BT/XNUC...
Page 274
R 1847 (B,142,119) (A,D) RS1/10SR223J R 1725 (B,89,74) RS1/16SS223J R 1848 (B,142,114) (A,D) RS1/10SR223J R 1726 (B,89,75) RS1/16SS223J R 1849 (B,142,120) (A,D) RS1/10SR181J R 1727 (B,85,75) RS1/16SS0R0J R 1850 (B,142,113) (A,D) RS1/10SR181J R 1728 (B,89,76) RS1/16SS0R0J R 1861 (B,166,7) RS1/16SS271J AVIC-X940BT/XNUC...
Page 275
C 1161 (A,167,66) CEVW100M16 R 2249 (A,98,15) RS1/16SS0R0J C 1162 (A,161,83) CKSSYB102K50 R 2250 (A,106,16) RS1/16SS0R0J C 1164 (A,161,86) CKSRYB104K50 C 1171 (A,156,97) CEVW100M16 R 2292 (A,90,30) RS1/16SS104J R 2312 (B,77,23) RS1/16SS101J C 1172 (A,161,95) CKSSYB102K50 R 2313 (B,77,22) RS1/16SS101J AVIC-X940BT/XNUC...
Page 276
C 1328 (B,81,38) CCSSCH180J50 C 1332 (B,83,36) CCSSCH680J50 C 1724 (B,91,80) CKSRYB105K10 C 1334 (B,84,44) CKSRYB103K50 C 1726 (B,91,79) CKSRYB105K10 C 1335 (B,83,44) CKSRYB105K10 C 1727 (B,91,82) CKSRYB105K10 C 1728 (B,91,84) CKSRYB105K10 C 1336 (B,85,49) CKSRYB103K50 C 1729 (B,91,83) CKSRYB105K10 AVIC-X940BT/XNUC...
Page 277
Micro SD PCB C 2018 (A,49,85) CKSRYB105K10 C 2019 (A,50,82) CKSSYB223K16 C 2020 (A,53,79) CKSSYB223K16 C 2021 (A,44,64) CCSRCH680J50 Unit Number : CWN6412(A) C 2022 (A,56,80) CKSRYB224K16 : CWN6413(B) : CWN6416(C) C 2023 (A,56,78) CKSSYB104K10 C 2024 (A,34,81) 10 uF CCG1192 AVIC-X940BT/XNUC...
Page 278
L 2901 (B,6,86) Inductor CTF1750 R 131 (A,55,74) RS1/10SR0R0J L 2902 (B,6,88) Inductor CTF1751 R 141 (A,134,10) RS1/10SR0R0J L 2903 (B,6,90) Inductor CTF1752 R 142 (A,56,22) RS1/10SR0R0J R 150 (A,105,12) RS1/10SR0R0J X 151 (B,17,96) TCXO 16.367 667 MHz CWX3728 AVIC-X940BT/XNUC...
Page 279
(A,118,107) (A,B,C,E,F) RS1/16SS0R0J R 5953 (B,11,16) RS1/16SS330J R 249 (A,122,107) (A,B,C,E,F) RS1/16SS0R0J R 251 (A,118,99) (A,B,C,E,F) RS1/16SS221J R 5954 (B,13,13) RS1/16SS0R0J R 252 (A,120,100) (A,B,C,E,F) RS1/10SR105J R 5955 (A,13,22) RS1/16SS0R0J R 254 (A,116,117) (A,B,C,E,F) RS1/8SQ102J R 5956 (A,16,22) RS1/16SS330J AVIC-X940BT/XNUC...
Page 280
C 273 (A,65,99) CKSRYB102K50 R 1027 (A,40,18) RS1/16SS101J C 274 (A,62,88) (A) CKSSYB104K10 C 275 (B,53,128) CKSRYB103K50 R 1101 (B,15,57) RS1/16SS104J C 276 (B,37,129) (A,B,D,E) CKSRYB103K50 R 1102 (B,10,56) RS1/16SS104J C 301 (A,56,79) (B,C) CKSRYB104K16 R 1103 (B,14,61) RS1/16SS4300F AVIC-X940BT/XNUC...
Page 281
C 1111 (A,9,66) CKSRYB224K16 R 1524 (B,29,33) RS1/16SS472J C 1112 (B,17,52) 22 uF DCH1256 C 1113 (B,8,58) 22 uF DCH1256 R 1525 (A,24,44) RS1/16SS103J C 1210 (B,77,34) CKSSYB104K16 R 1526 (A,22,40) RS1/16SS103J C 1251 (B,12,41) CEVW101M16 R 1527 (A,35,49) RS1/16SS682J AVIC-X940BT/XNUC...
Page 282
CKSSYB104K10 IC 4403 (A,46,77) Flash ROM Unit(Service) CXX4262 C 1614 (A,22,24) CKSSYB104K10 IC 4404 (B,71,95) IC H5DU5162ETR-E3C C 1615 (A,23,26) CKSSYB104K10 IC 4405 (B,71,67) IC H5DU5162ETR-E3C C 1616 (A,24,27) CKSSYB104K10 IC 4406 (A,36,70) SRAM CY62147EV30LL45BVA C 1617 (B,27,28) CKSSYB104K10 AVIC-X940BT/XNUC...
Page 284
R 3375 (A,16,40) RS1/16SS470J R 4065 (A,34,103) RS1/16SS222J R 3376 (B,9,24) RS1/16SS470J R 4066 (A,52,109) RS1/16SS0R0J R 3377 (B,12,19) RS1/16SS0R0J R 4067 (A,51,109) RS1/16SS0R0J R 3378 (B,10,26) RS1/16SS0R0J R 4068 (B,45,86) RS1/8SQ0R0J R 3380 (B,14,21) RS1/16SS223J R 4069 (A,39,77) RS1/16SS471J AVIC-X940BT/XNUC...
Page 285
(B,63,145) (B,C) RS1/16SS0R0J R 4206 (A,65,44) RS1/16SS4702D R 4289 (B,64,145) (D) RS1/16SS0R0J R 4207 (A,64,44) RS1/16SS1003D R 4290 (B,66,145) (E,F) RS1/16SS0R0J R 4208 (A,23,48) RS1/16SS4702D R 4291 (A,9,88) SMD Ferrite Beads CTF1802 R 4209 (A,22,49) RS1/16SS1003D R 4294 (B,45,73) RS1/10SR102J AVIC-X940BT/XNUC...
Page 286
R 4413 (B,79,72) RS1/16SS220J R 4636 (B,46,51) RS1/16SS0R0J R 4414 (A,52,77) RS1/16SS103J R 4637 (B,48,71) RS1/16SS0R0J R 4415 (A,64,70) RS1/16SS471J R 4638 (B,46,51) RS1/16SS0R0J R 4419 (A,52,78) RS1/16SS473J R 4639 (B,45,51) RS1/16SS0R0J R 4420 (B,64,92) RS1/16SS471J R 4640 (A,63,36) RS1/16SS473J AVIC-X940BT/XNUC...
Page 287
R 4816 (A,23,80) RS1/16SS103J R 5607 (B,43,139) RS1/16SS271J R 4817 (A,25,87) RS1/16SS470J R 5608 (B,42,137) RS1/16SS271J R 4818 (A,26,88) RS1/16SS300J R 5609 (B,42,139) RS1/16SS271J R 4819 (A,25,77) RS1/16SS0R0J R 5610 (B,41,137) RS1/16SS271J R 4821 (A,23,78) RS1/16SS0R0J R 5611 (B,41,139) RS1/16SS271J AVIC-X940BT/XNUC...
Page 288
C 3362 (A,18,34) CKSQYB106K6R3 C 4051 (B,45,91) CKSSYB104K10 C 3363 (A,18,36) CKSQYB106K6R3 C 4052 (B,47,100) CKSSYB104K10 C 3364 (A,16,31) CKSQYB106K6R3 C 4053 (B,45,90) CKSSYB104K10 C 3365 (A,17,31) CKSSYB102K50 C 4054 (B,43,92) CKSSYB104K10 C 3366 (A,13,30) CKSQYB106K6R3 C 4055 (B,46,93) CKSSYB104K10 AVIC-X940BT/XNUC...
Page 289
C 4218 (B,69,45) CCSSCH102J50 C 4412 (A,78,94) CKSSYB103K16 C 4219 (B,35,40) CKSSYB472K50 C 4413 (B,64,107) CKSRYB105K10 C 4222 (B,70,42) CCSSCH470J50 C 4414 (A,79,57) CKSSYB103K16 C 4223 (B,35,43) CCSSCH470J50 C 4415 (A,79,58) CKSSYB103K16 C 4224 (A,22,60) CKSSYB392K50 C 4416 (A,79,62) CKSSYB103K16 AVIC-X940BT/XNUC...
Page 290
C 4622 (B,58,53) CKSSYB473K16 C 4843 (B,23,122) CKSSYB103K16 C 4623 (B,49,51) CKSSYB473K16 C 4844 (B,22,122) CKSSYB103K16 C 4624 (B,41,54) CKSSYB473K16 C 4845 (B,21,122) CKSSYB103K16 C 4625 (B,49,70) CKSSYB473K16 C 4846 (B,22,120) CKSSYB103K16 C 4626 (B,56,70) CKSSYB473K16 C 4847 (B,23,120) CKSSYB103K16 AVIC-X940BT/XNUC...
Page 291
(B,30,128) 47 uF CCG1251 R 5006 (A,37,18) RS1/16SS0R0J C 4983 (B,29,125) CKSSYB103K16 R 5007 (A,35,20) RS1/16SS0R0J C 4985 (B,27,112) CKSSYB103K16 R 5008 (A,34,20) RS1/16SS0R0J C 4986 (B,25,111) CKSQYB106K6R3 R 5009 (A,33,20) RS1/16SS0R0J C 4987 (B,19,120) CKSQYB106K6R3 R 5010 (A,32,20) RS1/16SS0R0J AVIC-X940BT/XNUC...
Page 292
Miscellaneous Parts List R 5071 (A,58,20) RS1/16SS223J R 5072 (A,56,20) RS1/10SR4702D Motor Unit(CRG(L/E)) CXC4026 R 5073 (A,56,18) RS1/10SR3902D *M 2 Motor(SPINDLE) EXM2002 Fan Motor CXM1441 R 5074 (A,55,21) RS1/16SS100J R 5075 (A,65,31) RS1/10SR2R2J R 5076 (A,79,28) RS1/10SR0R0J R 5078 (A,56,40) RS1/16SS0R0J AVIC-X940BT/XNUC...