Installation, Setup And Configuration - Harman Kardon AVR 85 Owner's Manual

7. Connections to a subwoofer are made
via a line level audio connection from
the
Subwoofer Output ⁄
level input of a subwoofer with a built-in
amplifier. If a passive subwoofer is used,
the connection first goes to a power
amplifier, which will be connected to one
or more subwoofer speakers.
Video Input and Output Connections
Video connections are made in a similar
fashion to those for audio components.
Again, the use of high-quality intercon-
nect cables is recommended to preserve
signal quality.
1. Connect the VCR's audio, video and
S-Video OUT jacks to the
Video In
on the rear panel. The audio, video
e k
and S-Video IN jacks on the VCR should
be connected to the
Video Out
on the AVR85.
f j
2. Connect the audio and video outputs
of a satellite receiver, cable TV converter
or television set or any other video source
to the jacks .
ª
TV
3. Connect the audio, video and S-Video
outputs of a DVD or laser disc player to
the jacks .
•
DVD
4. Connect the
TV Mon g h
the receiver to the video, or S-Video
inputs, of your television monitor or
video projector.
5. As the AVR85 does not mix or change
between standard composite video and
S-Video signals, both monitor connec-
tions must be made if you use both
signal systems.
Note: The on-screen menus are visible
on the composite video output only.

Installation, Setup and Configuration

System and Power Connections
to the line
The AVR85 is designed for flexible use
with external control components and
power amplifiers. These connections are
easy to make during an initial installa-
tion, or at a later date should you choose
to upgrade your system.
Remote Control Extension
If the receiver is placed behind a solid or
smoked glass cabinet door, the obstruc-
tion may prevent the remote sensor from
receiving commands. In this event, an
optional remote sensor may be used.
Connect the output of the remote sensor
to the
Remote Cont. In
jacks
If other components are also prevented
from receiving remote commands, only
jacks
one sensor is needed. They may use this
unit's sensor or a remote eye by running
a connection from the
jack
d
Out
Harman Kardon or other compatible
equipment.
Multiroom System Connections
The AVR85 is capable of sending a sepa-
rate source from the one being listened
to in the main listening room to another
room in the house, and having the vol-
ume and source selection of the remote
jacks on
room feed be controlled by an optional
infrared remote control.
Connect the
Outputs i
audio amplifier that powers the remote
room speakers. If no remote sensor is
connected in the second room zone, the
level may be set via the AVR85's setup
menus (see page 34).
14
jack .
c
Remote Cont.
to the Remote In jack on
Multiroom Audio
to the input of the optional
True multiroom remote control is possi-
ble by placing an optional infrared sen-
sor in the second room zone. The cable
from that sensor should be connected to
the remote input
Multi IR
panel.
See page 34 for complete information on
using the AVR85's Multiroom capabilities.
External Audio Power
Amplifier Connections
If desired, optional external power audio
power amplifiers may be used with the
AVR85. Connections to these amplifiers
are made by using audio interconnect
cables connected to both the
on the rear panel and
Outputs ‚
the audio input jacks of the external
amplifiers.
AC Power Connections
This unit is equipped with two accessory
AC outlets. They may be used to power
accessory devices, but they should not be
used with high-current draw equipment
such as power amplifiers. The total power
draw may not exceed 50w to each outlet.
The outlet will receive
Switched fi
power only when the unit is on. This is
recommended for devices that have no
power switch, or a mechanical power
switch that may be left in the "ON"
position.
Note: Devices with electronic power
switches may only go into a Standby
mode when plugged in here.
fl
The outlet will receive
Unswitched
power as long as the unit is plugged into
a powered AC outlet.
Finally, when all connections are com-
plete, plug the power cord into a non-
switched 120-volt AC wall outlet. You're
almost ready to enjoy the AVR85!
on the rear
b
Preamp