Harman Kardon AVR 635 Owner's Manual page 14

MAIN REMOTE CONTROL FUNCTIONS
Speaker Select Button: Press this button
to begin the process of configuring the AVR 635's
bass management system. Then press the
Navigation Button o to select the channel you
wish to set up. Press the Set Button q and
then select another channel to configure. When all
adjustments have been completed, press the Set
Button q twice to exit the settings and return to
normal operation. (See page 27 for more information
on speaker setup.)
Memory Button: Press this button to enter a
radio station to the AVR 635's preset memory. First,
tune the desired station, and then press this button.
Within 5 seconds of when you see the station's
frequency flash in the Upper Display Line # and
in the on-screen display, press the numeric keys
for the preset number between 01 and 30 that you
wish to assign to the station. (See page 37 for more
information.)
Stereo Mode Select Button: Press this button
to select a stereo listening mode. When the button is
pressed so that SURROUND OFF appears in
the Lower Display Line $ , the AVR will operate
in a bypass mode with true, fully analog, two-channel
left/right stereo mode with no surround processing or
bass management, as opposed to other modes where
digital processing is used. When the button is pressed
so that SURROUND OFF appears in the Lower
Display Line $ , and the DSP and Surround Off
Surround Mode Indicators % are lit, you will enjoy
a two-channel presentation of the sound, along with
the benefits of bass management. Depending on
whether your system is configured for 5.1 or 6.1/7.1
channels, the next press of the button will cause either
5 CH STEREO or 7 CH STEREO to
appear, and the stereo signal will be routed to all five
(or seven) speakers. (See page 34 for more informa-
tion on stereo playback modes.)
DTS Neo:6 Mode Select Button: Press this
button to select a DTS Neo:6 mode. (See page 34
for the available DTS Neo:6 options.)
DTS Digital Mode Select Button: When a
DTS-encoded digital source is playing, each press of
this button will scroll through the available DTS modes.
The specific choice of modes will vary according to
the type of encoding on the disc and your system's
speaker configuration. When a DTS source is not in
use, this button has no function. (See page 34 for the
available DTS digital options.)
14 MAIN REMOTE CONTROL FUNCTIONS
Dolby Mode Select Button: This button is used
to select from the available Dolby Surround modes.
Each press of this button will select one of the Dolby
/
⁄ ¤
Pro Logic II, Pro Logic IIx or Dolby Virtual Speaker
modes, as available for the number of speakers in your
system. When a Dolby Digital-encoded source is in
use, the Dolby Digital mode may also be selected.
(See page 34 for the available Dolby surround
mode options.) 49 47 45 43
48 46 44 42
6-Channel/8-Channel Input Select: Press this
35 37 39 41
button to select the device connected to the 6- or 8-
34 36 38 40 37
Channel Direct Inputs 33 36
26 25 37
32 35
information.) 27 36
24
31 34
28 23 35
30 Mute Button: Press this button to momentarily
33
22
29 34
29
silence the AVR 635 or TV set being controlled, 32
21
30 33
28
31 32 31
20
depending on which device has been selected.
Lens: The infrared emitters behind the plastic
lens at the top of the remote communicate the remote
codes to the AVR 635. Be certain that the lens is not
covered when using the remote, and point the lens
toward the AVR for best results. In learning mode, the
remote receives IR codes to be learned through a
sensor behind the lens.
NOTE: DO NOT remove the rubber plug that covers the
jack on the upper right side of the remote. The jack is
not active and is reserved for future use.
41 51
47
40 . (See page 32 for more 46 50
39 45 49
44
38 48
43
12 42