Integra DRX-5 Manual page 25

> 開始之前 > 線路連接
多區域
播放
1. Switch the remote controller to the mode for
controlling ZONE 2 or ZONE 3.
To switch to the mode for controlling ZONE 2,
while holding down Mode (a) on the remote
controller, press Zone 2 (b) for 3 or more
seconds until the remote indicator blinks
twice.
To switch to the mode for controlling ZONE 3,
while holding down Mode (a) on the remote
controller, press Zone 3 (c) for 3 or more
seconds until the remote indicator blinks
three times.
2. 將搖控器指向主機，並按 Í (e)
主機螢幕上的"Z2" 或 "Z3" 燈亮起。
3. 按要於另一房間播放之輸入源的輸入選擇器按
鈕 (f) 。要在主機上進行控制，請按 Zone 2 或
Zone 3，並在 8 秒內按要於另一房間內播放之
輸入源的輸入選擇器按鈕。要在主聆聽室與另
一房間內播放相同音源，請按主機上的 Zone
2 或 Zone 3 兩次。
0 無法用 AM/FM 廣播為主聆聽室與另一房間
選擇不同的電台。 選擇另一房間的輸入源或
電台時，主聆聽室也會隨之切換。
> 設置 > 播放 > 零 件 名 稱
0 DSD 以及 Dolby TrueHD 音訊信號不會輸
出至 ZONE 2/ZONE 3 當輸入選擇器選擇
"NET" 。.
4. To adjust the volume on the power amplifier in
the separate room or the ZONE 2 SPEAKER,
adjust with VOL+/– on the remote controller.
To control on the main unit, press Zone 2 or
Zone 3 and adjust with the Master Volume
control within 8 seconds.
0 The information for a connected device can be
displayed on the TV screen in a separate room.
Press the
is in the mode for controlling ZONE 2.
0 Power consumption in standby mode
increases when the multi-zone function is
being used.
To turn off the function
Press Í while in the mode for controlling ZONE
2 or ZONE 3 on the remote controller.
Playing in ZONE 2 or ZONE 3 only
If you turn the unit to standby during multi-zone
playback, the Z2 or Z3 indicator is dimmed and
the playback mode is switched to playback in a
separate room only. Setting ZONE 2/ZONE 3 to
on while this unit is in standby will also switch
the playback mode to the same setting.
WHOLE HOUSE MODE
If you press Whole House Mode while playback
is being performed in the main room, the Whole
House Mode is turned on, "Z2" and "Z3" on the
display light at the same time and the playback
sources of all the rooms are switched to the
same source at once.
0 The sources that can be played in ZONE 2
can be played in all rooms.
0 This function cannot be used if headphones
are connected or audio is output from the
speakers of the TV.
設置
須於初始設置中進行設定， "4. Multi Zone
Setup" ( P21) 中使用多區域功能。欲檢查設
定內容，請參考以下資訊，按遙控器上的
on the remote controller, and check in the
Setup menu that is displayed.
– When you have connected a TV in the
separate room with an HDMI cable, have you
selected "Use" in "1. Input /Output Assign" –
button while the remote controller "TV Out/OSD" – "Zone2 HDMI"?
– When you are playing the audio from an AV
component in the separate room connected
with an HDMI cable, have you selected "Use"
in "1. Input /Output Assign" – "TV Out/OSD" –
"Zone2 HDMI"?
– When you have connected speakers in a
separate room with speaker cable, have you
selected "Zone 2" (or "Zone 2 A + B") in "2.
Speaker" – "Configuration" – "Zone
Speaker"?
– When you have connected a power amplifier
in a separate room with an analog audio
cable and you want to control the volume with
this unit, have you selected "Variable" in "7.
25