Sony DSC-HX7 Service Manual page 6

Ver. 1.2 2011.07
The changed portions from
Ver. 1.1 are shown in blue.
1-4-3. Self-diagnosis Code Table
Self-diagnosis Code
Symptom/State
Block Detailed
Function Code
The internal memory has experienced a me-
dia error.
The internal memory has experienced a for-
mat error.
Memory card is unformatted.
C 1 3 0 1
Memory card is broken.
Memory card type error
The camera cannot read or write data on the
memory card.
C 3 2 0 1 Trouble with hardware
Difficult to adjust focus
E 6 1 0 0
(Cannot initialize focus)
Zoom operations fault
E 6 1 1 0
(Cannot initialize zoom lens.)
E 6 2 0 2 Abnormality of IC for steadyshot.
E 6 2 1 0 Lens initializing failure.
E 6 2 1 1 Lens overheating (PITCH).
E 6 2 1 2 Lens overheating (YAW).
E 6 2 2 0 Abnormality of thermistor.
E 9 1 0 1 Abnormality when flash is being charged.
E 9 4 0 0 Internal memory fault
E 9 5 0 0 GPS hardware error
Note: After repair, be sure to perform "1-5. PROCESS AFTER FIXING FLASH ERROR".
DSC-HX7/HX7V_L2
Correction
Turn the power off and on again.
Format the internal memory.
Format the memory card.
Insert a new memory card.
Insert a supported memory card.
Turn the power off and on again, or taking out and inserting the memory
card several times.
Turn the power off and on again.
Retry turn the power on by the power switch. If it does not recover,
check the focus reset sensor of lens block (pin 6 of CN401 on the
SY-283 board). If it is OK, check the focus motor drive IC (IC401 on
the SY-283 board).
Retry turn the power on by the power switch. Check the zoom reset
sensor of lens block (pin 0 of CN401 on the SY-283 board) when
zooming is performed when the zoom button is operated. If it is OK,
check the zoom motor drive IC (IC401 on the SY-283 board).
Check of the IC for steadyshot (IC401 on the SY-283 board).
Check of the IC for steadyshot (IC401 on the SY-283 board).
Check the HALL element (PITCH) of optical image stabilizer (pin rk,
t; of CN401 on the SY-283 board). If it is OK, check PITCH angular
velocity sensor (SE401 on the SY-283 board) peripheral circuits.
Check the HALL element (YAW) of optical image stabilizer (pin ef,
eh of CN401 on the SY-283 board). If it is OK, check YAW angular
velocity sensor (SE401 on the SY-283 board) peripheral circuits.
Check the OIS temp sensor of optical image stabilizer (pin qs of
CN401 on the SY-283 board).
Checking of flash unit or replacement of flash unit. (Note)
Inspect the internal memory (IC201 on the SY-283 board).
Check whether the FP-1395 flexible board of connected between AT-
042 board and RL-108 board or RL-099 flexible board of connected
between SY-283 board and RL-108 board is broken, and check whether
it is inserted imperfectly.
If there is no problem the coaxial cable or flexible board, inspect or
replacement of the AT-042 or RL-108 board.
1-5. PROCESS AFTER FIXING FLASH ERROR
When "FLASH error" (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is changed
automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be on the HOME screen.
Method for Initializing the Flash Error Code
Reset Flash Error using the Flash Error Repair Tool Ver_[].[].exe.
1-3
– ENGLISH –