Table of Contents
Advertisement
Quick Links
Installation Manual of Room Air Conditioner
1.Driver
2.Hacksaw
3.Hole core drill
4.Spanner(17,19 and 26mm)
Accessory parts
No.
Accessory parts
1
Remote controller
2
R-03 dry battery
3
Mounting plate
4
Drain hose
5
4X25
Plastic cap
Screw
6
Drain-elbow
7
Pipe supporting plate
No.0010561789
Necessary Tools for Installation
5.Torque wrench(17mm,22mm,26mm)
6.Pipe cutter
7.Flaring tool
8.Knife
Drawing for the installation of indoor and outdoor units
Number
of
articles
Optional parts for piping
1
Mark
Parts name
A
Non-adhesive tape
2
Adhesive tape
B
Saddle(L.S) with screws
C
1
Connecting electric cable
D
for indoor and outdoor
Drain hose
E
F
Heating insulating material
1
Piping hole cover
G
4
1
1
Arrangement of piping directions
Rear left
Left
The marks from
A
to
G
The distance between the indoor unit and the floor should be
more than 2m.
Read this manual before installation
Explain sufficiently the operating means to the user
according to this manual.
The models adopt HFC free refrigerant R410A
Rear
right
Right
Below
in the figure are the parts numbers.
9.Nipper
10.Gas leakage detector or
soap-and-water solution
11.Measuring tape
Attention must be paid to
the rising up of drain hose
A
12.Reamer
C
D
E
Advertisement
Table of Contents
Related Manuals for Haier HSU-09RM03/R2
Summary of Contents for Haier HSU-09RM03/R2
-
Page 1: Installation Manual Of Room Air Conditioner
Installation Manual of Room Air Conditioner Necessary Tools for Installation 1.Driver 2.Hacksaw 3.Hole core drill 4.Spanner(17,19 and 26mm) Accessory parts Number Accessory parts articles Remote controller Mark R-03 dry battery Mounting plate Drain hose 4X25 Plastic cap Screw Drain-elbow Pipe supporting plate... -
Page 2: Selection Of Installation Place
Floor fixing dimensions of the outdoor unit (Unit:mm) HSU-09RM03/R2 HSU-12RM03/R2 HSU-18RM03/R2 Fixing of outdoor unit Selection of Installation Place Indoor Unit Place, robust not causing vibration, where the body can be supported sufficiently. Place, not affected by heat or steam generated in the vicinity, where inlet and outlet of the unit are not disturbed. -
Page 3: Indoor Unit
2.Making a Hole on the Wall and Fitting the Piping Hole Cover Make a hole of B mm in diameter, slightly descending to outside the wall. Install piping hole cover and seal it off with putty after installation HSU-09RM03/R2 HSU-12RM03/R2 HSU-18RM03/R2 HSU-24RM03/R2 HSU-28RM03/R2 When the mounting plate is first fixed ", for the... -
Page 4: Installation Of The Indoor Unit
3.Installation of the Indoor Unit Drawing of pipe Rear piping Draw pipes and the drain hose, then fasten them with the adhesive tape Left Left-rear piping In case of left side piping, cut away, with a nipper, the lid for left piping. In case of left-rear piping, bend the pipes according to the piping direction to the mark of hole for left-rear piping which is marked on heat insulation materials. - Page 5 4. After installation, the power plug should be easily reached. 5. A breaker should be incorporated into fixed wiring. The breaker should be all-pole switch and the distance between its two contacts should be not less than 3mm. YEL/GRN YEL/GRN Indoor unit HSU-09RM03/R2 HSU-12RM03/R2 YEL/GRN YEL/GRN Indoor unit HSU-24RM03/R2...
-
Page 6: Installation Of Outdoor Unit
20 g/m. But the charge of refrigerant must be conducted by professional air conditioner engineer. Before adding additional refrigerant, perform air purging from the refrigerant pipes and indoor unit using a vacuum pump,then charge additional refrigerant. - Page 7 After attaching the each caps, check the gas leakage around the caps. CAUTION: 1.If the refrigerant of the air conditioner leaks, it is necessary to discharge all the refrigerant. Vacuumize first, then charge the liquid refrigerant into air conditioner according to the amount marked on the name plate.
-
Page 8: Power Source Installation
1.Power Source Installation The power source must be exclusively used for air conditioner. (Over I0A) In the case of installing an air conditioner in a moist place, please install an earth leakage breaker. For installation in other places, use a circuit breaker as far as possible.