Bosch PSR 14,4 LI-2 Original Instructions Manual page 13

OBJ_BUCH-900-004.book Page 13 Thursday, November 26, 2015 1:59 PM
7 Battery pack*
8 "PowerLight"
9 Battery charge-control indicator
10 Rotational direction switch
11 On/Off switch
12 Handle (insulated gripping surface)
Technical Data
Cordless Drill/Driver
Article number
Rated voltage
No-load speed
– 1st gear
– 2nd gear
Max. torque for hard/soft screwdriving application according to ISO 5393
Max. screw dia.
Max. drilling dia.
– Steel
– Wood
Chuck clamping range
Weight according to EPTA-Procedure 01:2014
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted sound pressure level of the product
is 70 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Drilling into metal: a =2.5 m/s , K =1.0 m/s
h
2
Screwdriving: a =2.5 m/s , K =1.0 m/s
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardisation documents: EN 60745,
Bosch Power Tools
13 Battery unlocking button*
14 Universal bit holder*
15 Securing screw for keyless chuck
16 Allen key*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
EN 50581 according to the provisions of the directives
2009/125/EC (Regulation 1194/2012), 2011/65/EU,
2014/30/EU, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ETM9,
70538 Stuttgart, GERMANY
Henk Becker
Executive Vice President
Engineering
2
,
2
.
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Assembly
Battery Charging (see figure A)
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The Lithium-Ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
PSR 14,4 LI-2
3 603 J56 4..
V= 14.4
-1
min 0–370
-1
min 0–1150
Nm 38/20
mm 8
mm 10
mm 30
mm 0–10
kg 1.35
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
1 609 92A 1XP | (26.11.15)
English | 13
PSR 18 LI-2
3 603 J56 3..
18
0–400
0–1250
46/25
8
10
35
0–10
1.45