Table of Contents
Advertisement
Malfunction table
Malfunctions often have simple explanations. Please refer to the
malfunction table before calling the after-sales service.
If a meal does not turn out exactly as you wanted, refer to the
Tested for you in our cooking studio section, where you will
find plenty of cooking tips and tricks.
Malfunction table
Problem
The appliance does not work.
"Basic setting Clock 00:00" appears in
the display. The time displayed is not
the current time.
The oven door cannot be opened. The
text "Time 00:00" is shown in the dis-
play. The time displayed is not the cur-
rent time.
The oven does not heat up. When the
appliance is switched on, "Demo" is
displayed briefly.
"Automatic switch-off" appears in the
display.
The microwave does not switch on.
The appliance does not heat up to the
temperature which has been set.
Microwave operation has been can-
celled for no apparent reason.
With microwave operation, the food
takes longer to heat up than before.
Error messages with E
If an error message with E is shown in the display, press the
button. Then reset the clock. This cancels the error message. If
the error is shown again, call the after-sales service. With error
message E106, you can still operate the microwave.
If error message E011 is displayed, a button may have become
stuck. Press each button individually and check that they are all
clean. If the error message remains, please contact the after-
sales service.
Replacing the oven light bulb
It is possible to replace the oven light. Heat-resistant 12 V,
20 W halogen bulbs can be obtained from After-sales Service
or a specialist retailer.
:
Risk of electric shock!
Never replace the oven light when the appliance is switched on.
Pull out the mains plug or switch off the appliance at the circuit
breaker in the fuse box.
Possible cause
Faulty circuit breaker
Plug not plugged in
Power cut
Power cut
Power cut during self-cleaning operation
The oven is in demo mode
The automatic switch-off has been acti-
vated. The oven stops heating.
Door not fully closed.
The microwave was not started.
The
button was not pressed.
n
The microwave has a fault.
The microwave power setting is too low.
A larger amount than usual has been
placed in the appliance.
The food was colder than usual.
0
:
Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be carried
out by one of our trained after-sales engineers.
Remedy/information
Look in the fuse box and check that the circuit
breaker is in working order.
Plug it in.
Check whether the kitchen light works.
Turn the rotary selector to set the correct time,
then press the
Turn the rotary selector to set the correct time
then press the
ing compartment has cooled down. The
symbol goes out. You can now open the oven
door.
Switch off the circuit breaker in the fuse box
and then switch back on after approx.
20 seconds. In the next 2 minutes, press and
hold the
Press any button. The text disappears. You
can make settings again.
Check whether food remains or foreign mate-
rial is trapped in the door. Make sure that the
sealing surfaces are clean. Check whether the
door seal is twisted.
Press the
Press the
If this fault occurs repeatedly, please call the
after-sales service. Oven operation without
microwave is possible.
Select a higher power setting.
Double the amount = almost double the time
Stir or turn the food during cooking
Note: Always remove the new halogen bulb from the packaging
using a dry cloth. This increases the service life of the bulb.
Method
Switch off the circuit breaker in the fuse box.
1.
Place a tea towel in the cold oven to prevent damage.
2.
Remove the glass cover. To do so, prise open the glass
3.
cover at the bottom by hand.
Should you experience difficulties removing the glass cover,
use a spoon to help. (Fig. A)
0
button.
button. Wait until the cook-
0
button for 4 seconds.
D
n
button.
button.
n
H
21
Advertisement
Table of Contents
