Related Manuals for Nortel ATM T3
Summary of Contents for Nortel ATM T3
- Page 1 Part No. 313889-A Rev 00 September 2001 600 Technology Park Drive Billerica, MA 01821-4130 ATM T3/E3 PMC Module Supplement...
- Page 2 In the interest of improving internal design, operational function, and/or reliability, Nortel Networks Inc. reserves the right to make changes to the products described in this document without notice. Nortel Networks Inc. does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.
- Page 3 Canadian Department of Communications Radio Interference Regulations This digital apparatus (ATM T3/E3 PMC module) does not exceed the Class A limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.
- Page 4 (such as images, text, recordings or pictures) and related licensed materials including all whole or partial copies. Nortel Networks grants you a license to use the Software only in the country where you acquired the Software. You obtain no rights other than those granted to you under this License Agreement. You are responsible for the selection of the Software and for the installation of, use of, and results obtained from the Software.
- Page 5 C.F.R. 227.7202 (for DoD entities). Customer may terminate the license at any time. Nortel Networks may terminate the license if Customer fails to comply with the terms and conditions of this license. In either event, upon termination, Customer must either return the Software to Nortel Networks or certify its destruction.
-
Page 7: Table Of Contents
How to Get Help ......................xv Chapter 1 Using the ATM T3/E3 PMC Module Verifying Shipment Contents ..................1-2 Preparing to Install the ATM T3/E3 PMC Module ............1-3 Tools and Cables ......................1-4 Setting AC or DC Coupling .....................1-4 Installing a Jumper Head ..................1-5 Removing a Jumper Head ..................1-6... - Page 9 Removing a Jumper Head for AC Coupling ..........1-6 Figure 1-5. Installing the PMC Module ...............1-7 Figure 1-6. Securing the PMC Module to the System Processor Card ......1-8 Figure 1-7. Connecting the ATM T3 Cable ..............1-9 Figure 1-8. ATM T3/E3 PMC Module LEDs ..............1-10 313889-A Rev 00...
- Page 11 Tables Table 1-1. Accessories in the Passport 5430 Shipping Container ......1-2 Table 1-2. ATM T3 or E3 Interface Coupling .............1-5 Table 1-3. ATM T3/E3 Interfaces ................1-9 Table 1-4. ATM T3/E3 PMC LEDs ................1-10 313889-A Rev 00...
-
Page 13: Preface
Preface The Nortel Networks* ATM T3/E3 PMC module provides an interface to support unchannelized T3 or E3 operation for ATM applications. In this guide, the Passport* 5430 Multiservice Access Switch is referred to as the Passport 5430. Before You Begin This guide is intended for qualified service personnel who are installing or replacing the ATM T3/E3 PMC module into the Passport 5430. -
Page 14: Acronyms
ATM T3/E3 PMC Module Supplement Acronyms This guide uses the following acronyms: alternating current alarm indicator signal asynchronous transfer mode customer-replaceable unit direct current out of frame light emitting diode peripheral component interconnect PCI mezzanine card remote alarm indicator wide area network... -
Page 15: How To Get Help
Preface How to Get Help If you purchased a service contract for your Nortel Networks product from a distributor or authorized reseller, contact the technical support staff for that distributor or reseller for assistance. If you purchased a Nortel Networks service program, contact one of the following... -
Page 17: Using The Atm T3/E3 Pmc Module
This document supplements Installing and Operating the Passport 5430 Multiservice Access Switch. Follow the hardware installation steps in that manual, then refer to this document for information specific to the ATM T3/E3 PMC module. Warning: The ATM T3/E3 PMC module is designed to operate in the Passport 5430 Multiservice Access Switch only. -
Page 18: Verifying Shipment Contents
“How to Get Help” on -xv). In addition to the ATM T3/E3 PMC module and this guide, your shipping container should contain other hardware accessories. Verify that the items in the shipping container match those on the packing list affixed to the shipping... -
Page 19: Preparing To Install The Atm T3/E3 Pmc Module
Four panhead screws T3E3001 Figure 1-1. Shipping Contents Preparing to Install the ATM T3/E3 PMC Module Before beginning the installation, verify the following: • You have the proper equipment and tools; see “Tools and Cables” on page 1-4. -
Page 20: Tools And Cables
ATM T3/E3 PMC Module Supplement Tools and Cables To install the ATM T3/D3 PMC module into the Passport 5430 you need a Phillips screwdriver and the following equipment: • Two 75 ohm mini-SMB to BNC adapters (part of the shipping contents) •... -
Page 21: Installing A Jumper Head
To install a jumper head, go to the next section. To remove a jumper head, go to “Removing a Jumper Head” on page 1-6. Installing a Jumper Head To DC couple an ATM T3 or E3 interface, install the jumper head as follows: Locate the jumper pins (Figure 1-2 on page 1-4). -
Page 22: Removing A Jumper Head
Removing a Jumper Head for AC Coupling Installing the ATM T3/E3 PMC Module Note: The ATM T3/E3 PMC module can be installed only on the system processor card. Note: Before you install the ATM T3/E3 PMC module, be sure the transmitting and receiving interfaces are coupled appropriately;... - Page 23 Using the ATM T3/E3 PMC Module To install the PMC module on the system processor card: Attach an antistatic wrist strap. Caution: Electrostatic discharge can damage hardware. You must wear the antistatic wrist strap whenever you handle printed circuit boards. Refer to the instructions enclosed with your antistatic wrist strap to attach it.
- Page 24 ATM T3/E3 PMC Module Supplement Insert and tighten the four screws to secure the PMC module to the system processor card (Figure 1-6). T3E3003A Figure 1-6. Securing the PMC Module to the System Processor Card Install the system processor card into the chassis.
-
Page 25: Attaching Cables
You connect both interfaces to the T3/E3 communications device with the same types of cables. To connect to the ATM T3 or E3 interface on an installed ATM T3/E3 PMC module, you attach the 75 ohm mini-SMB to BNC adapter, then the 75 ohm BNC... -
Page 26: Interpreting Leds
Port 2 Port 2 Console T3E3006A Figure 1-8. ATM T3/E3 PMC Module LEDs Table 1-4 describes the function of the ATM T3/E3 PMC module’s LEDs. Table 1-4. ATM T3/E3 PMC LEDs State Meaning Sync Port is not synchronized to the network. -
Page 27: Completing The Software Configuration
On (yellow) Framer has detected a remote alarm indication signal. Completing the Software Configuration Once you have successfully installed the ATM T3/E3 PMC module, complete the following software configuration tasks using instructions found in the documentation: Configuration Task Location of Instructions... -
Page 29: Cables And Interface Specifications
Appendix A Cables and Interface Specifications Ports The T3/E3 interface consists of two 75 ohm mini-SMB connectors for a separate input and output communication port. With the appropriate cabling, each port can operate in either a T3 or an E3 configuration. Cabling The following cables are needed to attach the Passport 5430 to the T3/E3 communications device:... -
Page 30: Environmental Specifications
ATM T3/E3 PMC Module Supplement Environmental Specifications The environmental requirements for the ATM T3/E3 PMC module are as follows: • Altitude: 0 to 8000 ft. (0 to 2438.4 m) • Humidity: 40% to 90%, noncondensing • Temperature: 32° to 104°F (0° to 40°C)