Page 2
Cert No: HW110LGE-30 EU Declaration of Conformity Axminster Tool Centre Ltd This machine complies with the following directives: Axminster Devon EX13 5PH UK axminstertools.com 2006/42/EC 06/42/EC - Annex I/05.2006 declares that the machinery described:- EN 60204-1:2006+A1+AC EN 1870-19:2013 Type Table saw...
Page 4
3. Machine Description 3.1 Technical parameters Item HW110LGE-30 HW110LGE-50 260Kg (approx.) weight Product Dimensions length/width/height(mm) 1582x1100x1016 2090x1100x1016 foot print(length/width) 508x508 Electrical: switch magnetic with thermal overload protection type TEFC capacitor start induction horsepower/voltage/phase/amps 3HP-230V-1PH 12.8A Motor speed/cycle 2850 RPM/50HZ power transfer Triple V-belt Drive maximum blade diameter 250mm...
Page 7
3.5 Noise 4. Safety Regulations 3.5.1 Reference standards 4.1 General Safety Instructions measurements noise emission were 1. KNOW YOUR MACHINE. conducted according to the EN ISO 11202 for the Read and understand the owners manual and labels determination of sound pressure level at the affixed to the machine.
Page 8
in moving parts. Non-slip footwear is recommended. 4.2 Specific Safety Instructions for Wear protective hair covering to contain long hair. Sliding Table Saw Roll up long sleeves above the elbows; 1. ALWAYS USE A GUARD. 12. DON’T OVER REACH. Always use a guard, splitter and anti-kickback Keep proper footing and balance at all times;...
is directly under the red line on the pointer window as shown; lightly mark the “0” location on the tube with a pencil, then remove the fence; peel the tape and carefully align the “0” mark on the scale with the pencil mark you made;...
disengages the bracket and the locking pin engages 5.4.7 Install the blade the hole in the center of the spreader. A. Remove blade guard assembly & table insert. C. give the spreader an upward tug to verify that it is B.
electric power to this machine, in order to protect After finishing wiring on the spot, check the following people against electrical shock due to indirect shock items at least: Wiring: Check the wirings of machine. Finish electrical connection according to the Check the direction of motors and change wiring if electrical drawings.
Page 18
6.3 Aligning Table T-slot Parallel With 6.4 Adjusting 45 and 90 Degree Blade Positive Stops 1,The table T-slot must be aligned parallel with the The blade tilting mechanism of your saw is equipped blade. Using a combination square (A) as Fig.24, with a positive stop at 45 and 90 degrees.
matching set of V-belts onto the pulleys, lower the 8. Maintenance motor to tension the V-belts, then tighten the hex This table saw requires very little maintenance other nuts. than minor lubrication and cleaning. The following 4. Close the motor access cover. sections detail what will need to be done in order to assure continued operation of your saw.
9. Trouble Shouting Guide PROBLEM SOLUTION SAW WILL NOT START 1. Saw not plugged in. 1. Plug in saw. 2. Fuse blown or circuit breaker tripped. 2. Replace fuse or reset circuit breaker. 3. Cord damaged. 3. Have cord replaced by a certified electrician. OVERLOAD KICKS OUT FREQUENTLY 1.
Page 24
10. Parts List Table Saw Body Breakdown...
Page 34
50″Rail & Extension Table Breakdown 50″Rail & Extension Table Parts List REF# DERIPTION REF# DERIPTION foot tube cover cap screw M6*16 phlp HD screw M8-1.25×40 rear rail lock washer 6 tube flat washer 6 scale hex bolt 5/16-18x1-1/2 front rail lock washer 8 flat washer 8 extension table...
Page 35
Optional ST-1400 Sliding Table Code 104505 PART DESCRIPTION Lock Lever M8-1.25 Button HD Screw M6-1 x 12 Support Leg Lock Washer 6MM Hex Nut M8-1.25 Flat Washer 6MM Foot Pad Sliding Table Side Cover Lock Lever Flat Washer 8MM Sliding Table Assembly Stop Plate Cap Screw M8-1.25 x 25 Stop Pin Assembly...
1. Foreword This instruction manual only for the table saw equipped with ST1400 & RT100. The content includes: Product configuration and model, space requirements, the installation of switch box and the use of the guide rail. 2. Product configuration list Model Options HW110WS...
3. Space Requirements Before your setup, you must insure the interspace between the machine and wall at least 800mm. 3.1 Model :HW110S-S , HW110WS-S Fig.1...
Page 40
4. Change the installation position of switch When install the sliding table, you must change the installation position of the switch, you can install the magnetic switch onto the bottom of the sliding table with three sets hex bolts, as shown in Fig.3 M6-1x 12 hex bolts……..3 6mm lock washers...……3...
Page 45
The packaging is suitable for recycling. Please dispose of it in a responsible manner. EU Countries Only Do not dispose of electric tools together with household waste material. By law they must be collected and recycled separately. Axminster Tools, Axminster Devon EX13 5PH axminstertools.com...