ADC HiGain H2TU-C-319 List 3E Quick Installation

T H2TU-C-319 L 3E
HE IST
The H2TU-C-319 List 3E (H2TU-C) line unit is the Central Office (CO) side of a T1
transmission system. When the H2TU-C is used in conjunction with a HiGain
High-bit-rate Digital Subscriber Line 2 (HDSL2) remote unit (H2TU-R), the system
provides 1.552 Mbps transmission on one unconditioned copper pair over the full
Carrier Service Area (CSA) range. The CSA includes loops up to 12,000 feet of
24 AWG or 9,000 feet of 26 AWG wire, including bridged taps.
F
EATURES
• Front-panel status LED, craft port, and
four-character status display
• Ultra-low wander
• Grounded loop detection
• Loss of Signal (LOS)/Alarm Indication Signal
(AIS) payload alarm option
• Digital Data Service (DDS) latching loopback
option
• Sources sealing current
• Supports the inband 100 loopdown and
100000 loopup commands when the
SmartJack Loopback (LPBK) option is enabled
S
PECIFICATIONS
Operating Temperature
Operating Humidity
HDSL2 Span Voltage
Mounting
HDSL2 Line Rate
HDSL2 Output
Maximum Loop Attenuation
DSX-1 Line Rate
DSX-1 Line Format
DSX-1 Frame Format
DSX-1 Pulse Output
DSX-1 Input Level
• Payload (PL) or HiGain (HG) loopback source
identification
• Bit Error Rate (BER) alarm option
• Bipolar Violation Transparency (BPVT) option
• Report menu option for downloading status and
performance monitoring data to a file
• Maintenance screens for inventory, provisioning,
troubleshooting, and performance monitoring
• Performance Report Messaging (SPRM and NPRM)
• HDSL2 span connection to Loop 2 on pins K and
9
-40 °F to +149 °F (-40 °C to +65 °C)
5% to 95% non-condensing
0, -185 Vdc
3192 high-density shelf
1.552 Mbps Overlapped Pulse Amplitude Modulation
Transmission with Interlocking Spectra (OPTIS)
+16.8 dBm ±0.5 dB, 135 Ω (0-450 kHz) at CO side
+16.5 dBm ±0.5 dB, 135 Ω (0-350 kHz) at remote side
35 dB at 196 kHz, 135 Ω
1.544 Mbps ±200 bps
Alternate Mark Inversion (AMI) or Bipolar with 8-zero
Substitution (B8ZS)
Extended SuperFrame (ESF), SuperFrame (SF), or
Unframed (UNFR)
pk-pk
6 V , pre-equalized for 0 to 655 feet of ABAM cable
+1.5 to -7.5 dB DSX
I
NSTALLATION
When installing an H2TU-C, wear an antistatic wrist strap.
Avoid touching components on the circuit board.
To ensure proper installation of the, align the H2TU-C with the enclosure slot guides,
and slide the unit in. Push down on the front panel to properly seat it.
P - S
OWER UP EQUENCE
When the H2TU-C powers up, the four-character display illuminates and reports
status messages.
If the H2TU-C is unable to communicate with the H2TU-R, it displays various alarm
and status messages.
If the H2TU-C is able to communicate with the H2TU-R, the following occurs:
1 The Status LED flashes red while acquiring the H2TU-R and turns a steady green
when the entire system is operating with no alarms. (The DS1 signal must be
present.)
The four-character display reports margin (SNR) readings (should be ≥ 6 dB) and
2
loop attenuation (should be <35 dB @196 KHz).
3 After the system powers up, alarm conditions that exist are reported on the
display. (The H2TU-C reports alarms if no DS1 signal is applied.)
P
ROVISIONING
After installation, perform these basic provisioning tasks from the HiGain HDSL2
logon screen. Refer to the onscreen Help menu for navigational aids.
1 Connect a maintenance terminal to the craft port (see front-panel illustration
inside), then press + to refresh the logon screen, if necessary.
CTRL R
2 Select the Config menu, Date and Time, then type the date and time.
3 Select the Inventory menu, then type in the unit ID numbers.
4 Change the settings of any system parameters, if necessary, by selecting the
Config menu, Standard Options or ADC Options. (Configuration options can
also be set from the front panel using the MODE and SEL buttons. See the
"Front-Panel Configuration Options Using MODE and SEL" table inside.)
Þ
Continued