Maintenance; General; Daily Cleaning; Replacing Display Light Bulbs - Hatco Glo-Ray GRSDS Series Installation And Operating Manual

English

General

Hatco Glo-Ray Merchandising Display Warmers are designed
®
for maximum durability and performance with minimum

maintenance.

WARNING
ELECTRIC SHOCK HAZARD:
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning, setup, or
maintenance.
• Units with two power cords must have both power
supply cords disconnected before performing any
cleaning, adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• Do not clean unit when it is energized or hot.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
This unit has no "user-serviceable" parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
Form No. GRSDM-0121

Daily Cleaning

To preserve the finish of the unit as well as maintain
performance, it is recommended that the unit be cleaned daily.
IMPORTANT—DO NOT use paper towel or glass cleaner
to clean plastic surfaces such as sneeze guards and
flip-up doors. Paper towel and glass cleaner may scratch
the material. Wipe off plastic surfaces using a soft, clean,
water-dampened cloth.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
1. Turn off the unit, unplug the power cord(s), and allow the
unit to cool.
• Units with two power cords must have both power
supply cords disconnected before performing any
cleaning, adjustments, or maintenance.
2. Remove and wipe down the product divider rods and
channel dividers.
3. Wipe down all exterior and interior surfaces using a water-
dampened cloth. A non-abrasive cleaner may be used for
difficult stains. Hard to reach areas should be cleaned
using small brush and mild soap.
4. Clean the glass side panels using a standard glass
cleaner.
5. Clean the plastic sneeze guards and flip-up doors (if
equipped) using soft cleaning cloths, mild soap, and water,
if equipped. NOTICE: Do not use paper towel or glass
cleaner on plastic surfaces — scratching may occur.

Replacing Display Light Bulbs

Use only light bulbs that meet or exceed National
Sanitation Foundation (NSF) standards and are specifically
designed for food holding areas. Breakage of light bulbs
not specially coated could result in personal injury and/or
food contamination.
The display light is an incandescent light bulb that illuminates
the warming area. The bulb has a special coating to guard
against injury and food contamination in the event of breakage.
1. Turn off the unit, unplug the power cord(s), and allow the
unit to cool.
• Units with two power cords must have both power
supply cords disconnected before performing any
cleaning, adjustments, or maintenance.
2. Unscrew the light bulb from the unit and replace it with a
new, specially-coated incandescent light bulb.
NOTE: Hatco shatter-resistant light bulbs meet NSF
standards for food holding and display areas. For
120 and 120/208–240 V applications, use Hatco P/N
02.30.043.00.
NOTE: Shatter-resistant halogen bulbs are available in place
of the standard incandescent bulbs. Halogen bulbs
have a special coating to guard against injury and
food contamination in the event of breakage. For
120 and 120/208–240 V applications, use Hatco P/N
02.30.081.00.
13
MAINTENANCE
NOTICE
WARNING