Related Manuals for Sentry Saf-T-Vise STV-HP3
Summary of Contents for Sentry Saf-T-Vise STV-HP3
- Page 1 Original Instructions Installation, Operation & Maintenance Manual Saf-T-Vise STV-HP1 and STV-HP3 Insertable Tool Holders S-CM-IOM-00506-3 03-22...
- Page 2 Sentry Equipment Corp instructions Otherwise, injury, damage, or both may result Copyright © 2022 by Sentry Equipment Corp All rights reserved All product and company names are property of their respective owners This document contains proprietary information No part of this document may be photocopied or reproduced...
-
Page 3: Table Of Contents
Table of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 General Safety Precautions . -
Page 4: Safety Information
. minor or moderate injury . Â NOTE Information that requires special emphasis . Â TIP Alternate techniques or clarifying information. SHALL: This word is understood to be mandatory SHOULD: This word is understood to be advisory Sentry Equipment Corp... -
Page 5: General Safety Precautions
General Safety Precautions Product Selection, Installation, and Use Improper selection, installation, or use can cause personal injury or property damage . It is solely the responsibility of users, through their own analysis and testing, to select products suitable for their specifi c application requirements, ensure they are properly maintained, and limit their use to their intended purpose . -
Page 6: General Description
General Description The Sentry® Saf-T-Vise STV-HP1 and STV-HP3 insertable tool Indicator holders are multi-functional tools that can be equipped to button monitor pipeline corrosion, inject chemical into the process, or sample the pipeline medium The holders are engineered Safety cap... -
Page 7: Maintenance
Maintenance  NOTE Saf-T-Vise STV-HP1 All maintenance procedures assume the or STV-HP3 insertable tool holder has been properly removed the Saf-T-Vise STV-T Series Insertion Tools manual from the line . See for instructions . Inspecting the Safety Cap ƒ Remove safety cap from holder and ensure the red indicator is still in good condition ƒ... -
Page 8: Changing A Rod/Shaft And Replacing A Seal
If the upper body is difficult to remove, stop immediately and make sure that the set screw is loose . 3. Replace the seal a. With the upper body removed, use a pick or small screwdriver to gently pick out the old seal b. Clean the seal body of the holder with a clean rag Sentry Equipment Corp... - Page 9 c. Insert new seal: ƒ For Teflon seal: – Place the new Teflon seal onto the seal insertion tool with the seal opening facing away from the handle – Lubricate the open-faced edge of the seal with Molykote 55 or other fine viscosity lubricant by placing a dot of lubricant on your finger, then slowly rolling your finger around the outside lip of the seal, completely coating the outside edge –...
-
Page 10: Changing A Coupon/Checking Probe End
2. Remove old coupon or inspect the rod/shaft as needed 3. Clean the rod/probe shaft 4. If using a coupon holder, attach the new coupon 5. Reinstall the tool holder into the pipeline by following instructions for specific insertion tool Sentry Equipment Corp... -
Page 11: Troubleshooting
Troubleshooting Leaks Multi-Port Valve Leaks 1. Isolate and bleed down the pressure, and attempt to tighten the leak point If leak persists, continue with next step 2. Re-tape the fittings on the multi-port valve a. Remove the entire holder from the process line b. -
Page 12: Locking Collet
Standard Warranty Sentry Equipment Corp (“Seller”) warrants products manufactured by it and supplied hereunder (“Products”) to be free from defects in workmanship and, to the extent materials are selected by Seller, to be free from defects in materials, in... -
Page 13: Customer Support
ƒ Field Service & Retrofi ts—When a problem needs immediate attention ƒ Replacements Parts & Consumables—Order your replacement parts and consumables ƒ Sentry ProShield Services—Select from four ProShield Guardian service plans providing diff erent levels of support to protect your large system investments with regularly scheduled maintenance... - Page 14 This page is intentionally left blank Sentry Equipment Corp...
- Page 15 This page is intentionally left blank Saf-T-Vise STV-HP1 and STV-HP3...
- Page 16 Serving customers in more than 50 countries across six continents worldwide. sentry-equip.com 966 Blue Ribbon Circle North, Oconomowoc, WI 53066 U.S.A. | +1-262-567-7256 | support@sentry-equip.com...