Table of Contents
Advertisement
OPERATION AND MAINTENANCE Continued
LOCATING ACCESS COVER PLATE
Sheet metal cover plates located underneath front hearth refractory may
have shifted or moved out of place while fireplace was in transit. These
cover plates must be kept in the proper location prior to using the fireplace
(See Figure 26).
For further operating guidelines, instructions and warranty informa-
tion, please refer to your homeowner's guide or contact your dealer.
Access
Panel
Figure 26 - Locating Access Cover Plate
REPLACEMENT PARTS
See Pages 16 to 18 for a complete replacement parts list. Use only
parts supplied from the manufacturer.
Normally, all parts should be ordered through your IHP distributor
or dealer. Parts will be shipped at prevailing prices at time of order.
When ordering repair parts, always give the following information:
1. The model number of the fireplace.
2. The serial number of the fireplace.
3. The part number.
4. The description of the part.
5. The quantity required.
6. The installation date of the fireplace.
If you encounter any problems or have any questions concerning the
installation or application of this fireplace, please contact your dealer.
IHP
1769 East Lawrence Street
Russellville, AL 35654
Visit us at SuperiorFireplaces.us.com
TECHNICAL SERVICE
You may have further questions about installation, operation, or
troubleshooting. Please contact your IHP dealer for any questions
or concerns. When contacting your dealer please have your model
and serial numbers of your fireplace ready. You can also visit our
web site at SuperiorFireplaces.us.com.
126628-01_J
IMPORTANT NOTICES - CANADA
A manufactured shroud which has been approved by a
national testing agency for use with this fireplace may
be used if installed in accordance with the instructions
by its manufacturer. A locally fabricated shroud may be
used with IHP Shroud Leg Spacer Kit (SLK) in accor-
dance with instructions provided with the shroud.
NOTICE: The firebox canopy (hood) must not be modified
or replaced with a canopy that may be provided with the
unvented decorative room heater.
CAUTION: THE STRUCTURAL INTEGRITY OF THE MANU-
FACTURED HOME FLOOR, WALL, AND CEILING/ROOF
MUST BE MAINTAINED.
WARNING: DO NOT INSTALL IN SLEEPING ROOM OF
MOBILE HOMES.
Canadian code CAN/ULC-S610-M87 and other pertinent codes require stain-
less steel chimney for the installation of this fireplace. A Cold Air Climate
Kit is also required in Canada and is recommended for cooler regions in the
United States. Below, find a list of approved stainless steel parts.
Catalog
Model No.
No.
F0881
12-8HT
F0882
18-8HT
F0883
24-8HT
F0884
36-8HT
F0885
48-8HT
F0886
30E-8HT
F0887
12S-8HT
F0888
RT-8HT
F0889
RTT-8HT*
F0890
RLT-8HT
F0891
RLTT-8HT*
F0892
ET-8HT*
F0893
ETL-8HT*
F0894
AP-8HT
F0929
CAK-8
*When ordered alone, this part cannot ship via parcel delivery services.
SuperiorFireplaces.us.com
IMPORTANT NOTICE
Chimney Parts List for Canada
8" Hi-Temp
Wood burning Chimney
12" Section Hi-Temp Double Wall Pipe Snap Lock
18" Section Hi-Temp Double Wall Pipe Snap Lock
24" Section Hi-Temp Double Wall Pipe Snap Lock
36" Section Hi-Temp Double Wall Pipe Snap Lock
48" Section Hi-Temp Double Wall Pipe Snap Lock
30 Degree Hi-Temp Offset and Return
Hi-Temp Chimney Support (For Use With Chimney
Heights In Excess of 30')
Hi-Temp Round Top with Mesh Screen
Hi-Temp Round Top with Mesh Screen and Slip
Section
Hi-Temp Round Top with Louvered Screen
Hi-Temp Round Top with Louvered Screen and
Slip Section
Hi-Temp Pyramid Top with Slip Section
Hi-Temp Large Pyramid Top with Slip Section (use
with all 8" systems)
Hi-Temp Anchor Plate/Collar Assembly (for ma-
sonry fireplaces)
Cold Air Collar Kit - 8" Chimney
15
Advertisement
Table of Contents
