Summary of Contents for Chicago Electric HVLP-ELECTRIC 97750
Page 1
PAINT SPRAYER HVLP-ELECTRIC SET uP ANd OPERATINg INSTRuCTIONS Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. distributed exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com...
SAVE THIS MANuAL Keep this manual for the safety warn- ings and precautions, assembly, operat- ing, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Page 3
Unmodified plugs and matching out- lets will reduce risk of electric shock. Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. do not expose power tools to rain or wet conditions.
Many accidents are caused by poorly maintained power tools. Keep the power tool clean. er cleaning of the Paint Sprayer and its accessories is a common reason for the Spray Gun to jam or not per- form properly.
Page 5
Do not spray pesticides, acids, cor- rosive materials, fertilizers, and toxic chemicals. do not leave the Paint Sprayer un- attended when it is plugged into an electrical outlet. Turn off the tool, and unplug it from its electrical outlet before leaving.
gROuNdINg TO PREVENT ELECTRIC SHOCK ANd dEATH FROM INCORRECT gROuNdINg WIRE CONNECTION: Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. do not modify the Power Cord Plug (34) provided with the tool. Never remove the grounding prong from the Plug.
Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Outlets for 2-Prong Plug.) Extension Cords Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord.
For technical questions, please call 1-800-444-3353. TO PREVENT SERIOuS INjuRY FROM ACCIdENTAL OPERATION: Turn the Power Switch (33) of the Paint Sprayer to its “OFF” position and unplug the tool from its electrical outlet before assembling, operating, or making any adjustments to the tool.
Work Piece and Work Area Set up Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent injury and distraction. Route the Power Cord (34) along a safe route to reach the work area without creating a tripping hazard or exposing the Power Cord to pos- sible damage.
Page 10
To get the best results, try to apply two thin coats of paint/fluid versus one thick coat. When finished, thoroughly clean out the Paint Sprayer and its accessories. (See “Maintenance and Servicing” section, next page.) (HEAVIER COAT...
TO PREVENT SERIOuS INjuRY FROM ACCIdENTAL OPERATION: Turn the Power Switch (33) of the Paint Sprayer to its “OFF” position and unplug the tool from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. TO PREVENT SERIOuS...
WARNINg! If the Power Cord (34) of this Paint Sprayer is dam- aged, it must be replaced only by a qualified service technician. SKU 97750 For technical questions, please call 1-800-444-3353.
TROuBLESHOOTINg - gENERAL Improper cleaning is a common reason for the unit not to work properly. Most problems can be avoided or remedied with prompt, thorough cleaning. Problem Possible Causes Sputtering Low fluid level. spray. Cup tipped too far. Clogged air vent. Loose fluid inlet connections.
Page 14
TROuBLESHOOTINg - SPRAY PATTERN Improper cleaning is a common reason for the unit not to work properly. Most problems can be avoided or remedied with prompt, thorough cleaning. The illustrations below resemble symptoms of spray pattern problems. Refer to the illustration your Spray Gun may be experiencing. Then refer to the “Possible Causes”...
PARTS LIST & ASSEMBLY dIAgRAM Part # Shoulder Strap (35) not shown. SKU 97750 For technical questions, please call 1-800-444-3353. description Part # Seal Nut Fluid Control Screw Gasket O-Ring Fluid Nozzle Gasket Air Nozzle Top Cover Air Cap Screw Cup Gasket Trigger Lower Cover...
LIMITEd 90 dAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this prod- uct is free from defects in materials and workmanship for the period of 90 days from the date of purchase.