Contents - Broan BKSJ130WW Installation Use And Care Manual

3¼"
M
AXIMUM
* Standard elbows with 1" internal radius.
NOTE: 6" round ducting is possible but may reduce exhaust efficiency.

Contents

Before proceeding to the installation, check the contents of the box. If items are missing or
damaged, contact the manufacturer.
Make sure that the following items are included:
(2) G
(1) 7" R
D
UCT
Use this template for marking; do not attempt to cut out the ducting hole through it.
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l'installation; elles ne doivent pas
être du format exact des conduits.
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
C Bend template along graduated
scale when installing to framed
cabinet.
Pour une installation sous une
armoire à fond en retrait, utiliser les
lignes pour mesurer l'épaisseur du
décalage causé par le mur de
l'armoire et plier le gabarit en
conséquence. 8"
To be translated in Spanish.
V RTICAL EX VERTICAL EXHAUST
C
Place this edge against back wall
8
Maximum Duct Lengths Recommended
to Achieve 80% Exhaust Efficiency
10" H 3¼"
X ORIZONTAL X
D M
UCT LENGTH AXIMUM
68 ft.
60 ft.
51 ft.
(2) LED B
(4W, GU10)
F (
REASE ILTERS INSTALLED ON HOOD
* F
IND INSIDE OF HOOD
OUND
(1) 3¼"
C
ONNECTOR
D
AMPER ASSEMBLY
EZ1 C
OMPONENTS
M ARK WHERE INDICATED
FOR THE APPROPRIATE SIZE DUCT OPENING
7" R OUND D UCTING OR R ECTANGULAR D UCTING
= 3¼" x 10"
= 3¼" x 14"
M ARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
LE FORMAT DE CONDUIT UTILISÉ
C ONDUIT ROND DE 7 PO OU C ONDUIT RECTANGULAIRE
= 3¼ po x 10 po
= 3¼ po x 14 po
T ITLE TO BE TRANSLATED IN S PANISH
C L
C ONDUCTO REDONDO O C ONDUCTO RECTANGULAR (1) T
7 . = 3¼ pulg. x 10 pulg.
DE PULG EMPLATE FOR DUCTING
= 3¼ pulg. x 14 pulg.
7½" Electrical access hole center
A = single blower hood
B = double blower hood (
PRINTED BOTH SIDES
Centre du trou pour fil
A A S d'alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
10½"
To be translated in Spanish
Electrical access hole center
4¼"
A = single blower hood
B = double blower hood
14½"
A B
C
Appuyer ce bord au mur arrière Apoyar este borde contra la pared de atrás
(2) I B
NSTALLATION
FOR FRAMED CABINET
(2) I B
NSTALLATION
FOR FRAMELESS CABINET
** F EZ1 B
IND RACKETS
ATTACHED INSIDE OF HOOD
(1) P B *** C :
ARTS AG ONTAINING
(4) N . 8-18 1/2"
O X
M S
ETAL CREWS
(6) N . 8 5/8"
O X
(6) N
RD. HD.
C
OUNTERSUNK
W S
OOD CREWS
W
OOD
*** F
(1) B S
IND PARTS BAG BEHIND
ULB UCTION
THE DAMPER ASSEMBLY
C T
UP OOL
INSIDE OF HOOD
7" R
OUND
10" V
ERTICAL
M
AXIMUM
D
UCT LENGTH
D
UCT LENGTH
51 ft. 57 ft.
42 ft. 42 ft.
33 ft. 28 ft.
ULBS
)
10"
X
*
)
**
RACKETS
**
RACKETS
. 8 1/2"
O X
S
CREWS
R
OOF OR
E (
LBOW S
W
ALL CAP
(90° /
AND OR
D
WITH AMPER
1 0
1 1
1 2
)*
45°)