Chart ... 12 Clean Up ... 13 assembly ... 13 Base Mounting ... 16 Mounting options ... 17 test run ... 18 Model g4173 ⁄ hp power Feeder table of contents SEctiON 4: OPERatiONS ... 19 operation safety ... 19 Basic Use and Care ...
Foreword We are proud to offer the Model g4173 power Feeder. this machine is part of a growing grizzly family of fine woodworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of grizzly’s com-...
Machine Data Sheet Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G4173 BABY POWER FEEDER Weight... 20 lbs. Length/Width/Height... 31 x 11 x 12 in. Foot Print (Length/Width)... N/A x N/A Type...
Page 6
Serial Number Location ... Serial Number Sticker On Motor Specification Plate Outside The Motor Assembly Time ... 20 minutes Rollers are Spring Tensioned Heavy-Duty Gear Reduction with Hardened Gears Universal Positioning with Handle Locks Model g4173 ⁄ hp power Feeder...
Figure 1 and your power feeder to familiarize yourself with the controls, features, and terminology used in this manual. doing so will make setup, use, and any future maintenance easier. 1⁄8 hp Motor Model g4173 ⁄ hp power Feeder...
⁄ hp power Feeder Power connection Device the Model g4173 comes with a 5-15 plug, similar to Figure 2, to connect the machine to power. Figure 2. typical 5-15 plug and receptacle. this machine MuSt have a ground prong in the plug to help ensure that it is grounded.
Otherwise, filing a freight claim can be difficult. When you are completely satisfied with the condi- tion of your shipment, inventory the contents. Model g4173 ⁄ hp power Feeder...
Model g4173 ⁄ hp power Feeder Figure 3. Box inventory. Figure 4. hardware inventory. if any nonproprietary parts are missing (e.g. a nut or a washer), we will gladly replace them;...
Figure 5. Cleaner/degreaser available from grizzly. Model g4173 ⁄ hp power Feeder to correctly position this power feeder on your table top, completely assemble the power feeder first, then refer to Base Mounting on page 17.
Page 16
Figure 10. assembling arm bracket. 11. insert the horizontal crank (Figure 10) com- pletely so it engages the spline in the gear (Figure 9). spline lock lever Flat Washer hex Nut Bracket Cover horizontal Crank Model g4173 ⁄ hp power Feeder...
Page 17
16. thread the t-handle into the elbow clamp so both assemblies are secure as shown in Figure 13. 17. Use the levers to lock the power feeder into position, such as the example shown in Figure 14. Model g4175 Quick holder Figure 14.
Figure 17. direct mounting. or if support webbing is in the way, the threads may strip or loosen as the power feeder is used. thread locking compound will not cure this situ- ation. revert to the through-bolt Mounting option.
OMMEND that you read books, trade maga- zines, or get formal training before begin- ning any projects. Regardless of the con- tent in this section, Grizzly industrial will not be held liable for accidents caused by lack of training. Model g4173 ⁄...
Wipe down the adjust- ment arm with a thin film of oil as required to pre- vent surface rust but not enough to attract dirt. Model g4173 ⁄ hp power Feeder...
1. lumber has high moisture content. when planing or moulding. 2. dull knives/cutter. Workpiece hangs 1. power feeder roller height is set incorrectly. 1. lower the power feeder roller and does not enter the machine. Model g4173 ⁄ hp power Feeder...
... 1 to replace the brush set: disCoNNECt thE poWEr FEEdEr FroM poWEr! Unscrew both brush caps (Figure 21). Figure 21. Brush set replacement. replace the brush set (Figure 21) and rein- stall the caps. Model g4173 ⁄ hp power Feeder...
Wiring Diagram Motor Control Circuit Board Fuse Motor speed dial Feed direction switch Figure 22. Feeder Control system. -24- READ ELECTRICAL SAFETY Model g4173 ⁄ hp power Feeder ON PAGE 23!
PLW06M LOCK WASHER 10MM PB14M HEX BOLT M10-1.5 X 35 PN02M HEX NUT M10-1.5 P4173183 TORSION SPRING P4173184 DATA LABEL P4173185 GRIZZLY LOGO LABEL P4173186 GENERAL WARNING LABEL P4173188 WHEEL COVER P4173189 ENTANGLEMENT LABEL Model g4173 ⁄ hp power Feeder...