(shorting-solder) by referring to "the DISASSEMBLY". 4. After replacing the pickup unit, be sure to check the grating. 5. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by electrostatic induction. DEH-9/XU/UC...
Page 3
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. DEH-9/XU/UC...
• Screw adjacent to mark on the product are used for disassembly. • For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.) 2.1 PACKING DEH-9/XU/UC...
No differentiation is made between chip capacitors and 0.022 R022 discrete capacitors. The > mark found on some component parts indicates CN1801 the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. D832 FTZ6R8E DEH-9/XU/UC...
Page 15
TUNER AMP UNIT REAR OUTPUT > > DEH-9/XU/UC...
3.4 CD MECHANISM MODULE CD CORE UNIT(S10.5) PICKUP UNIT(P10.5)(SERVICE) M1 CXC7134 SPINDLE MOTOR M2 CXC4026 LOADING/CARRIAGE MOTOR SWITCHES: CD CORE UNIT(S10.5) S901:HOME SWITCH..ON-OFF S903:DSCSNS SWITCH..ON-OFF CD DRIVER S904:12EJ SWITCH.....ON-OFF S905:8EJ SWITCH....ON-OFF The underlined indicates the switch position. DEH-9/XU/UC...
Page 23
SIGNAL LINE FOCUS SERVO LINE TRACKING SERVO LINE CARRIAGE SERVO LINE SPINDLE SERVO LINE CD DSP CN651 & DEH-9/XU/UC...
Page 24
1 V/div # FE % RFAGC @ TE 500 mV/div 500 mV/div 500 mV/div 9 TIN 500 mV/div Focus Search waveform Track Open waveform 1 Track Jump waveform Ref.: Ref.: Ref.: REFO REFO REFO Mode: Mode: Mode: TEST TEST TEST DEH-9/XU/UC...
Page 25
5 V/div 5 V/div 1 V/div 4 LOEJ 0 FIN 5 V/div 1 V/div Black dot(800 µm) during play 12 cm CD Eject operation 8 cm CD Eject operation Ref.: Ref.: Ref.: REFO Mode: Mode: Mode: Normal Normal Normal DEH-9/XU/UC...
For further information for respective destinations, be sure to check with the schematic dia- CORD ASSY gram. 2.Viewpoint of PCB diagrams Capacitor Connector SIDE A SIDE B Chip Part P.C.Board CN702 CN1801 DEH-9/XU/UC...
Page 27
SIDE A REAR OUTPUT ANTENNA FRONT DEH-9/XU/UC...
R 251 (B,101,104) RS1/16S223J R 252 (B,135,99) RS1/16S223J D 991 (A,17,110) Diode HZS7L(C3) L 151 (A,135,103) Inductor LAU2R2K R 301 (B,93,105) RS1/16S153J L 401 (A,147,79) Inductor LAU2R2K R 351 (B,163,128) RS1/16S223J L 402 (A,143,96) Inductor LAU2R2K R 352 (B,163,132) RS1/16S223J DEH-9/XU/UC...
Page 35
C 613 (A,102,56) CEAL101M6R3 R 834 (A,81,20) RD1/4PU222J C 614 (B,166,86) CKSRYB102K50 R 835 (A,59,18) RD1/4PU222J C 615 (B,122,59) CKSRYB331K50 R 837 (A,74,16) RD1/4PU103J C 616 (B,122,67) CKSRYB105K10 R 839 (A,86,12) RD1/4PU222J C 617 (B,128,58) CKSRYB105K10 R 840 (A,84,12) RD1/4PU222J DEH-9/XU/UC...
Page 36
CL-195PG-CD D 1808 (A,36,44) LED CL-195PG-CD RESISTORS D 1809 (A,20,136) LED CL-195PG-CD D 1810 (A,22,126) LED NESW505C-5273 R 101 (B,57,73) RS1/10SR2R4J D 1812 (A,31,29) LED CL-195PG-CD R 102 (B,60,73) RS1/10SR2R4J R 103 (B,60,70) RS1/10SR2R7J D 1813 (A,20,35) LED CL-195PG-CD DEH-9/XU/UC...
Page 37
C 219 (A,43,47) CKSSYB104K10 C 220 (B,39,45) CKSSYB104K10 C 221 (A,43,43) CKSSYB104K10 C 222 (A,44,50) CKSSYB104K10 C 223 (A,46,54) CCSSCH680J50 C 224 (A,44,56) CCSSCH470J50 C 225 (A,44,60) CKSSYB103K16 C 229 (B,46,55) CKSSYB104K10 C 231 (B,33,32) CKSSYB102K50 C 232 (B,32,29) CKSSYB102K50 DEH-9/XU/UC...
1k ohms in series. • The load and eject operation is not guarantied with the mechanism upside down. If the mechanism is blocked due to mistaken eject operation, reset the product or turn off and on the ACC to restore it. DEH-9/XU/UC...
Page 39
• When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the same time all the self-adjusting values shall return to the default setting. DEH-9/XU/UC...
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. • Hint Reloading the disc changes the clamp position and may decrease the "wobble". DEH-9/XU/UC...
Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors). Unreadable TOC does not constitute an error. An intended operation continues in this case. Upper digits of an error code are subdivided as shown below: 1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors. DEH-9/XU/UC...
TESTIN IC601(Pin 112) terminal to H. The clock signal is output from the SCET IC601(Pin 43) terminal. The frequency of the clock signal is 1 Hz. The clock signal should be 1 Hz ± 0.000 04 Hz. If the clock signal is out of the range, the X'tal (X601) should be replaced with new one. DEH-9/XU/UC...
Fig.1 Grille Assy Removing the Tuner Amp Unit (Fig.2) Remove the two screws. Remove the two screws. Straighten the tabs at two locations indicated. Remove the two screws and then remove the Tuner Amp Unit. Tuner Amp Unit Fig.2 DEH-9/XU/UC...
Page 45
Upper Frame. 3. While lifting the Carriage Mechanism, remove it from the three Dampers. Caution: When assembling, be sure to apply some alcohol to the Dampers and assemble the mechanism in a clamped state. Damper Damper Carriage Mechanism Lower Frame DEH-9/XU/UC...
Page 46
Assemble the sub unit side of the Pickup, taking the plate (Chassis) in-between. When treating the leads of the Load Carriage Motor Assy, do not make them loose over the Feed Screw. Poly Washer Change Arm Pickup Lock Arm Inner Holder Feed Screw Planet Gear Pickup Rack Chassis Pickup DEH-9/XU/UC...
Page 50
Terminal for TUNER only DGND2 Terminal for TUNER only L_OUT R_OUT Terminal for TUNER only Terminal for TUNER only COMP Terminal for TUNER only Terminal for TUNER only AVDD2 Terminal for TUNER only AGND2 ASUB Terminal for TUNER only DEH-9/XU/UC...
Page 51
CD mechanism power supply output Not used Self-rewriting applied voltage input 1(fixed to L) FLMD1 Not used Wired remote control input KEYD Not used 131,132 GND for port 7 P7AVSS P7AVDD VDD for port 7 A/D converter GND AVSS DEH-9/XU/UC...
Page 53
Key data output MODA Crystal oscillator connection pin Crystal oscillator connection pin 25,26 KDT2,3 Key data input Not used KST4 Key strobe output 29-32 Not used 33-55 SEG35-13 LCD segment output Power supply 57-64 SEG12-5 LCD segment output PD6340A DEH-9/XU/UC...
Page 54
Ground for the digital port IO.GND Power supply for the digital port IO.VDD Focus drive output (PWM) Tracking drive Sled drive Motor drive output (PWM) TEST Test Ground for the A/D converter AD.GND Power supply for the A/D converter AD.VDD EFM signal DEH-9/XU/UC...
Page 55
Impedance connection to focus error amp for negative feedback Focus error amp output A/D converter input ADCIN Impedance connection to tracking error amp for negative feedback Tracking error amp output Tracking error amp output multiplied by two Tracking error comparator PE5497B DEH-9/XU/UC...
Page 56
Output pin for preamplifier for thread OPINLSL Input pin for preamplifier for thread OPOUT3 CH3 preamplifier output pin OPIN3(-) Input pin for inverting input for CH3 preamplifier OPIN3(+) Input pin for non-inverting input for CH3 preamplifier PREVCC PreVcc BA5839FP DEH-9/XU/UC...
Page 57
Chip enable for FE_IC "High" active 18 DO Data Out Data output 19 CE2 Chip Enable-2 Chip enable for EEPROM "Low" active. in power ON/OFF, please turn CE2 into "High" (= VDD). 20 SLOUT Signal Level Output Output of FM/AM signals level (D.C.) DEH-9/XU/UC...
In case of the above signal, the communication Source keys with Grille microcomputer may fail. operative If the time interval is not 300 msec, the oscillator may be defective. Source ON SYSPW←H Pin 15 Completes power-on operation.(After that, proceed to each source operation.) DEH-9/XU/UC...
Page 64
CD Mechanism Module Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned Cleaning tools CD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 g p p DEH-9/XU/UC...